48,5 39 ø 53 13,5
Transcripción
48,5 39 ø 53 13,5
LM-SCED, LM-SCED (V) Installation Netz/ Mains/ Réseau/ Rete/ Red/ Net/ Nät LUXMATE-Bus Bus LUXMATE LM-SCED Art.-Nr. 24 046 764, LM-SCED (V) Art.-Nr. 24 046 820 L N PE 230V AC, 50Hz B1 B2 15V Taster Momentary action switches Poussoirs Pulsanti Pulsador Toetsen T1 T2 TR B1 B2 LM-SCED 13,5 ø 53 39 48,5 d Schalt-Eingang mit 2 unabhängigen Eingängen zum Stimmungsabruf mit konventionellen Lichttastern Technische Daten Verlustleistung . . . . . . . . . . . . . . . . . . . . . . < 0,5W Eingänge . . . . . . . . . . . . . . . . . . . . . . . . . . LUXMATE-Bus, 2 einpolige Eingänge Adressierung . . . . . . . . . . . . . . . . . . . . . . . 1 Adresse pro Eingang: Raumschalter: Raumadresse > 0; Gruppenadresse = 0 Gruppenschalter: Raumadresse > 0; Gruppenadresse > 0 Betreibsart . . . . . . . . . . . . . . . . . . . . . . . . . COMMON (Alles) Anschlussklemmen . . . . . . . . . . . . . . . . . . . 0,5...1,5mm2 Montage . . . . . . . . . . . . . . . . . . . . . . . . . . . in Unterputzdose hinter Taster/Schalter Abmessungen . . . . . . . . . . . . . . . . . . . . . . Ø 53mm, Höhe 15mm Gehäusematerial . . . . . . . . . . . . . . . . . . . . . flammwidriges Polycarbonat; halogenfrei Gewicht . . . . . . . . . . . . . . . . . . . . . . . . . . . ca. 100g zul. Umgebungstemperatur . . . . . . . . . . . . 0...50°C Schutzart . . . . . . . . . . . . . . . . . . . . . . . . . . IP 20 Sonstiges . . . . . . . . . . . . . . . . . . . . . . . . . . Taster aus Standard-Tasterprogramm (ohne Glimmlampen, Schaltthyristoren, ...). Spannung an Tasterleitung: 15V LM-SCED (V) Je nach Adressierung eines Eingangs können alle LUXMATE-Ausgänge eines Raumes oder eine Ausgangsgruppe des Raumes bedient werden: Durch die kurze Betätigung des an einen der beiden Eingänge angeschlossenen Tasters kann zwischen den zwei spezifizierten Stimmungen "X" und "Y" gewechselt werden (Stimmungswechsel pro Tastendruck). Installationshinweise •D as LM-SCED, LM-SCED (V) wird hinter dem Taster in die Unterputzdose eingelegt. • Die Leitungen T1, T2 und TR für den Anschluss des Tasters dürfen nicht verlängert werden. • Das Gerät wird ausschließlich über den LUXMATE-Bus versorgt und darf nicht an das Netz angeschlossen werden. Ebenso die Taster - diese werden nur an das LM-SCED, LM-SCED (V) angeschlossen und nicht an das Netz. • Schaltkontakte mit nicht extern versorgter Glimmlampe, RC-Glied und Schaltthyristoren werden vom LM-SCED, LM-SCED (V) nicht eindeutig erkannt und dürfen nicht verwendet werden. Bedienung mit Tastern LM-SCED Je nach Adressierung eines Eingangs können alle LUXMATE-Ausgänge eines Raumes oder eine Ausgangsgruppe des Raumes bedient werden: Durch die kurze Betätigung des an einen der beiden Eingänge angeschlossenen Tasters kann zwischen den zwei Stimmungen "Abwesend 0" und "Anwesend 1" gewechselt werden (Stimmungswechsel pro Tastendruck). Sicherheitshinweise Einsatzbereich •D ie Installation dieses Gerätes darf nur durch ausgewiesenes Fachpersonal erfolgen. • Die geltenden Sicherheits- und Unfallverhütungsvorschriften sind zu beachten. Das Gerät darf nur • für den bestimmungsgemäßen Einsatz verwendet werden, • fest in trockener und sauberer Umgebung installiert werden und • so installiert werden, dass ein Zugriff nur mit Werkzeug möglich ist. www.zumtobel.com [email protected] LUXMATE Lighting Management Text-ID: LM-SCED, LM-SCED(V)_IA 100212_PJ © e Switching input with 2 independent inputs for scene recall using conventional momentary action light switches Technical Data Power loss . . . . . . . . . . . . . . . . . . . . . . . . . < 0,5W Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LUXMATE bus, 2 single-pole inputs Addressing . . . . . . . . . . . . . . . . . . . . . . . . . 1 address per input Room switches: Room address > 0; Group address = 0 Group switches: Room address > 0; Group address > 0 Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . COMMON (all) Connecting terminals . . . . . . . . . . . . . . . . . 0,5...1,5mm2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . in concealed box behind (momentary action) switch Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . diam. 53mm, height 15mm Case material . . . . . . . . . . . . . . . . . . . . . . flame-resistant polycarbonate; halogen free Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . approx. 100g Permissible ambient temp. . . . . . . . . . . . . . 0...50°C Protection type . . . . . . . . . . . . . . . . . . . . . . IP 20 Miscellaneous . . . . . . . . . . . . . . . . . . . . . . momentary action switches from standard range of products (without neon lamps, switching thyristors, etc.) Voltage on momentary action switch line: 15V Operating with Momentary Action Switches LM-SCED Depending on the addressing of an input, it is possible to control all LUXMATE outputs of a room or one output group of the room: By a short actuation of the momentary action switch connected to one of the two inputs it is possible to change between the two scenes "Absent 0" and "Present 1" (scene changeover with each press of the switch). LM-SCED (V) Depending on the addressing of an input, it is possible to control all LUXMATE outputs of a room or one output group of the room: By a short actuation of the momentary action switch connected to one of the two inputs it is possible to change between the two specified scenes "X" and "Y" (scene changeover with each press of the switch). Installation Notes •T he LM-SCED, LM-SCED (V) is positioned behind the momentary action switch in the concealed box. • The lines T1, T2 and TR for connecting the momentary action switch must not be extended. • The device is powered exclusively over the LUXMATE bus and must not be connected to the mains. The same applies to the momentary action switches - these are connected only to the LM-SCED, LMSCED (V) and not to the mains. • Switching contacts with non externally supplied neon lamps, RC element and switching thyristors are not properly identified by the LM-SCED, LM-SCED (V) and must therefore not be used. Safety instructions Areas of application • Installation of this device may only be carried out by specialist staff who have provided proof of their skills • The relevant safety and accident prevention regulations must be observed. The device may only • be used for the applications specified • for safe installation in dry, clean environment • be installed in such a way that access is only possible using a tool. f Module avec 2 entrées indépendantes pour commande d'éclairages à partir de bouton-poussoirs conventionnels Caractéristiques Puissance dissipée . . . . . . . . . . . . . . . . . . < 0,5W Entrées . . . . . . . . . . . . . . . . . . . . . . . . . . . . LUXMATE-Bus, 2 entrées unipolaires Adressage . . . . . . . . . . . . . . . . . . . . . . . . . 1 adresse par entrée: Commutateur de local: Adresse de local > 0; Adresse de groupe = 0 Commutateur groupe: Adresse de local > 0; Adresse de groupe > 0 Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . COMMON (tous) Bornes de raccordement . . . . . . . . . . . . . . 0,5...1,5mm2 Montage . . . . . . . . . . . . . . . . . . . . . . . . . . . sous crépi derrière le bouton-poussoir/le commutateur Dimensions . . . . . . . . . . . . . . . . . . . . . . . . Ø 53mm, hauteur 15mm Matériau boîtier . . . . . . . . . . . . . . . . . . . . . . polycarbonate avec traitement anti-feu; sans halogène Poids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . env. 100g Temp. ambiante admissible . . . . . . . . . . . . 0...50°C Type de protection . . . . . . . . . . . . . . . . . . . IP 20, Divers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . touches, bouton-poussoirs standards usuels (sans voyant lumineux incorporé, sans thyristors, ...) Tension au niveau du bouton-poussoir: 15V LM-SCED (V) Selon l'adressage d'une entrée peuvent être commandés toutes les sorties LUXMATE d'un local ou un groupe de sorties déterminé: En actionnant brièvement un bouton-poussoir connecté à une des deux entrées, deux ambiances définies "X" et "Y" peuvent être déclenchés selon le cas (changement de l'ambiance avec chaque pression du bouton-poussoir). Consignes pour l'installation •L e module LM-SCED, LM-SCED (V) se monte derrière la touche ou le bouton-poussoir en encastré. • Les lignes T1, T2 et TR pour le raccordement du bouton-poussoir ne doivent pas être rallongées. • L'appareil est alimenté exclusivement par le bus LUXMATE, aucun branchement à la tension secteur à faire. De même pour les bouton-poussoirs- ceux-ci se raccordent uniquement au LM-SCED, LM-SCED (V) et non pas à la tension secteur. • Les contacteurs incorporant un voyant lumineux, un composant RC et thyristors sans alimentation à partir de l'extérieur ne sont pas détectés de façon univoque par le LM-SCED, LM-SCED (V) et ne doivent pas être utilisés. Commande avec bouton-poussoirs LM-SCED Selon l'adressage d'une entrée peuvent être commandés toutes les sorties LUXMATE d'un local ou un groupe de sorties déterminé: En actionnant brièvement un bouton-poussoir connecté à une des deux entrées, deux ambiances définies "Absence 0" et "Présence 1" peuvent être déclenchés selon le cas (changement de l'ambiance avec chaque pression du bouton-poussoir). Sécurité et précautions d'emploi Application •L 'installation de cet appareil doit obligatoirement être réalisée par un technicien qualifié. • Respecter la réglementation en matière de sécurité et de prévention des accidents en vigueur. L'appareil peut uniquement • être utilisé conformément à sa destination • être monté solidement dans un milieu sec et net • être placé de sorte qu'on ne puisse y accéder qu'avec un outil. Installation LM-SCED, LM-SCED (V) LM-SCED Art.-Nr. 24 046 764, LM-SCED (V) Art.-Nr. 24 046 820 i Entrata di attivazione con 2 ingressi indipendenti per il richiamo delle ambientazioni con pulsanti luminosi convenzionali Dati tecnici Dissipazione di potenza . . . . . . . . . . . . . . . < 0,5W Ingressi . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bus LUXMATE, 2 ingressi unipolari Indirizzamento . . . . . . . . . . . . . . . . . . . . . . 1 indirizzo per entrata: Interruttore per locali: indirizzo locale > 0; indirizzo gruppo =0 Interruttore per gruppi: indirizzo locale > 0; indirizzo gruppo >0 Modo operativo . . . . . . . . . . . . . . . . . . . . . COMMON (tutto) Morsetti . . . . . . . . . . . . . . . . . . . . . . . . . . . 0,5..1,5mm2 Montaggio . . . . . . . . . . . . . . . . . . . . . . . . . in cassetta da incasso dietro a pulsanti/interruttori Dimensioni . . . . . . . . . . . . . . . . . . . . . . . . . Ø 53mm, altezza 15mm Materiale alloggiamento . . . . . . . . . . . . . . . antifiamma Policarbonato; privo di alogeni Peso . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ca. 100g Temp. ambiente ammessa . . . . . . . . . . . . . 0...50°C Tipo di protezione . . . . . . . . . . . . . . . . . . . . IP 20 Altro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pulsanti della linea di tasti standard (senza lampade fluorescenti, tiristori di commutazione, ecc.). Tensione sulla linea del pulsante: 15V Comando con i tasti LM-SCED A seconda dell’indirizzamento di un ingresso, possono essere comandate tutte le uscite LUXMATE di un locale o un gruppo di uscite del locale: attraverso il breve azionamento del pulsante collegato ad uno dei due ingressi è possibile passare tra le due ambientazioni "Assente 0" e "Presente 1" (cambio di ambientazione con l’attivazione di un tasto). LM-SCED (V) A seconda dell’indirizzamento di un ingresso, possono essere comandate tutte le uscite LUXMATE di un locale o un gruppo di uscite del locale: attraverso il breve azionamento del pulsante collegato ad uno dei due ingressi è possibile passare tra le due ambientazioni specificate "X" e "Y" (cambio di ambientazione con l’attivazione di un tasto). Istruzioni per l'installazione •L M-SCED, LM-SCED (V) viene inserito dietro il pulsante nella cassetta da incasso. • Le linee T1, T2 e TR per il collegamento del tasto non possono essere prolungate. • L'apparecchio viene alimentato esclusivamente tramite il bus LUXMATE e non può essere collegato alla rete. Lo stesso dicasi per i tasti - questi possono essere collegati solo a LM-SCED, LM-SCED (V) e non alla rete. • I contatti di commutazione, dotati di lampada fluorescente non alimentata esternamente, elemento RC o tiristori di commutazione, non vengono riconosciuti in modo univoco da LM-SCED, LM-SCED (V) e non possono essere quindi utilizzati. Note sulla sicurezza Restrizioni d‘uso l‘apparecchio •L ’installazione di questo apparecchio richiede necessariamente l’intervento di personale specializzato. • Vanno rispettate le normative di sicurezza e di prevenzione dei sinistri. può essere usato solo • per le applicazioni cui è destinato; • installare in un ambiente secco e pulito •va installato in modo tale che l’accesso sia possibile solo con l’uso di un adeguato attrezzo esp Entrada de conmutación con 2 entradas independientes para la activación de ambientaciones con pulsadores de luz convencionales. Datos técnicos Potencia disipada . . . . . . . . . . . . . . . . . . . . < 0,5W Entradas . . . . . . . . . . . . . . . . . . . . . . . . . . . Bus LUXMATE, 2 entradas unipolares Asignación de direcciones . . . . . . . . . . . . . 1 dirección por cada entrada: Interruptor de una sala: dirección de la sala > 0, dirección del grupo = 0 Interruptor de un grupo: dirección de la sala > 0 dirección del grupo > 0 Modo de servicio . . . . . . . . . . . . . . . . . . . . COMMON (todo) Bornes de conexión . . . . . . . . . . . . . . . . . . 0,5...1,5mm2 Montaje . . . . . . . . . . . . . . . . . . . . . . . . . . . en cajas empotradas, detrás de pulsadores/interruptores Dimensiones . . . . . . . . . . . . . . . . . . . . . . . . Ø 53mm, altura 15mm Material de la carcasa . . . . . . . . . . . . . . . . . policarbonato pirorretardante; sin halógeno en su composición Pes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 g, aprox. Temperatura ambiente adm. . . . . . . . . . . . . 0...50°C Tipo de protección . . . . . . . . . . . . . . . . . . . IP 20 Otros datos . . . . . . . . . . . . . . . . . . . . . . . . Pulsador de la serie estándar (sin lámparas de efluvios, tiristores de conmutación, ...). Tensión en el cable del pulsador: 15V LM-SCED (V) En función de las direcciones asignadas a una entrada, podrán activarse todas las salidas LUXMATE de una sala o sólo un determinado grupo de ellas. Con el pulsador conectado a una de las dos entradas, una pulsación breve del mismo permite cambiar entre dos ambientaciones específicas "X" e "Y" (cambio de ambientación a cada pulsación). Instrucciones de instalación •E l LM-SCED, LM-SCED (V) se instala en la caja empotrada detrás del pulsador. • No se pueden prolongar los cables de conexión del pulsador T1, T2 y TR. • La alimentación eléctrica del aparato se realiza exclusivamente a través del bus LUXMATE, por lo que no se debe conectar a la red. Lo mismo es válido para los pulsadores, que sólo pueden conectarse al LM-SCED, LM-SCED (V) y no a la red. • El LM-SCED, LM-SCED (V) no reconoce correctamente los contactos de trabajo equipados con lámparas de efluvios sin alimentación externa, módulos RC o tiristores de conmutación, por lo que no se deben utilizar tales dispositivos. Manejo con pulsadores LM-SCED En función de las direcciones asignadas a una entrada, podrán activarse todas las salidas LUXMATE de una sala o sólo un determinado grupo de ellas . Con el pulsador conectado a una de las dos entradas, una pulsación breve del mismo permite cambiar entre las dos ambientaciones "Ausencia 0" y "Presencia 1" de personas (cambio de ambientación a cada pulsación). Instrucciones de Seguridad Areas de aplicación • La instalación de este aparato debe ser obligatoriamente realizada por personal debidamente cualificado. • Deben tenerse en cuenta las precauciones de seguridad y prevención de accidentes correspondientes. El aparato debe ser • usado solamente para las aplicaciones especificadas • instalado fijamente en ambiente seco y limpio • instalado en modo que el acceso al mismo sea posible solamente con uso de herramientas. nl Schakelingang met 2 onafhankelijke ingangen voor het oproepen van stemmingen met conventionele lichttoetsen Technische gegevens Vermogensverlies . . . . . . . . . . . . . . . . . . . . < 0,5W Ingangen . . . . . . . . . . . . . . . . . . . . . . . . . . LUXMATE-bus, 2 eenpolige ingangen Adressering . . . . . . . . . . . . . . . . . . . . . . . . 1 adres per ingang: Ruimteschakelaar: Ruimte-adres > 0; Groepsadres = 0 Groepsschakelaar: Ruimte-adres > 0; Groepsadres > 0 Werkwijze . . . . . . . . . . . . . . . . . . . . . . . . . . COMMON (Alle) Aansluitklemmen . . . . . . . . . . . . . . . . . . . . 0,5...1,5mm2 Montage . . . . . . . . . . . . . . . . . . . . . . . . . . . in inbouwdoos achter toetsen/schakelaars Afmetingen . . . . . . . . . . . . . . . . . . . . . . . . . Ø 53mm, hoogte 15mm Kastmateriaal . . . . . . . . . . . . . . . . . . . . . . . vlamwerend polycarbonaat; halogeenvrij Gewicht . . . . . . . . . . . . . . . . . . . . . . . . . . . ong. 100g Toelaatbare omgevingstemp. . . . . . . . . . . . 0...50°C Beveiliging . . . . . . . . . . . . . . . . . . . . . . . . . IP 20 Overigen . . . . . . . . . . . . . . . . . . . . . . . . . . . Toetsen uit standaard-Toetsenassortiment (zonder glimlampen, schakelthyristoren, ...). spanning aan toetsleiding: 15V Bediening met toetsen LM-SCED In functie van de adressering van een ingang kunnen alle LUXMATE-uitgangen van een kamer of kan een uitgangsgroep van deze kamer worden bediend: door het kort activeren van de aan een van de beide ingangen aangesloten toets kan tussen de twee stemmingen "Afwezig 0" en "Aanwezig 1" worden gewisseld (stemmingswisseling per toetsdruk). LM-SCED (V) In functie van de adressering van een ingang kunnen alle LUXMATE-uitgangen van een kamer of kan een uitgangsgroep van deze kamer worden bediend: door het kort activeren van de aan een van de beide ingangen aangesloten toets kan tussen de twee gespecificeerde stemmingen "X" en "Y" worden gewisseld (stemmingswisseling per toetsdruk). Installatie-instructies •D e LM-SCED, LM-SCED (V) wordt achter de toetsen in de inbouwdoos ingebouwd. • De leidingen T1, T2, en TR voor de aansluiting van de toets mogen niet verlengd worden. • Het apparaat wordt uitsluitend via de LUXMATE-bus gevoed en mag niet aan het net worden aangesloten. Dit geldt ook voor de toetsen - deze worden alleen aan de LM-SCED, LM-SCED (V) aangesloten en niet aan het net. • Schakelcontacten met niet extern gevoede glimlampen, RC-bestanddelen en schakelthyristoren worden door de LM-SCED, LM-SCED (V) niet feilloos herkend en mogen niet gebruikt worden. Veiligheidsinstructies Toepassingen •V oor werkzaamheden aan het apparaat dient de stroomverzorging uitgeschakeld te worden. • De geldende veiligheids- en ongevalpreventievoorschriften dienen in acht te worden genomen. Het apparaat mag alleen • voor de bedoelde toepassingen gebruikt worden, • vast in een droge en schone omgeving geïnstalleerd worden en • zo geïnstalleerd worden, dat toegang uitsluitend met werktuigen mogelijk is.
Documentos relacionados
LM-SFED_IA 030722
Raumes bzw. eine Fenster-Ausgangsgruppe des Raumes geöffnet und durch die Betätigung eines an die Klemme "T↓" angeschlossenen Tasters geschlossen werden. Wird ein Taster längere Zeit (> 3s) betätig...
Más detallesLM-SDED, LM-SDED (V)_IA 030722
• L'apparecchio viene alimentato esclusivamente tramite il bus LUXMATE e non può essere collegato alla rete. Lo stesso dicasi per i tasti - questi possono essere collegati solo a LM-SDED, LM-SDED (...
Más detalles