american drew
Transcripción
american drew
american drew ® ASSEMBLY INSTRUCTIONS 079 - 690 4310 Regency Drive, Suite 101 High Point, NC 27265 336-294-5233 www.americandrew.com TOOLS REQUIRED: F C D Wrench (A), supplied Allen Wrench (E), supplied Phillips Screwdriver (not supplied) Figure 1 Figure 2 E BEFORE YOU START: G 1. Check the parts against the parts list to make sure all items are present. 2. Assemble your furniture on a soft, flat surface to avoid scratching the finish. 3. CAUTION: Do not over tighten screws, nuts or bolts during assembly. 4. Your furniture may require occasional tightening. C D D C B A Figure 3 INSTRUCTIONS: 1. Attach the Seat Frame to the Back Leg using two Bolts (G), with a Lock Washer (C) and a Flat Washer (D) placed on each Bolt (G). Tighten with the Allen Wrench (E). See Figure 1. 2. Attach the Seat Frame to the Back Frame using the Bolt (F) with a Lock Washer (C) and then a Flat Washer (D) placed on the Bolt (B) first. Tighten with the Allen Wrench (E). See Figure 2. 3. Attach both Front Legs to the Seat Frame by placing a Flat Washer (D), then a Lock Washer (C), then a Nut (B) on the Leg Bolts. Leave the Nuts (B) loose. See Figure 3. 4. Place the stretchers between the back legs and the front legs and secure with two Wood Screws (H) per stretcher. See Figure 4. 5. Place the front stretcher, between the two front legs and secure with two Wood Screws (H). See Figure 5. 6. Tighten all the Nuts, Bolts and Screws before using your Chair. H Front Stretcher Side Stretcher HARDWARE LIST No. E ITEM DESCRIPTION Qty A Wrench 1 B Nut 5/16” 4 C 9 D Lock Washer 5/16” Flat Washer 5/16” E Allen Wrench 5/16” 1 F Bolt 5/16” x 1-1/2” 1 G H Bolt 5/16” x 3” 4 Wood Screw 1-1/4” 6 Figure 4 9 Thank you for purchasing furniture from american drew drew ® american INSTRUCTIONS DE MONTAGE 079 - 690 4310 Regency Drive, Suite 101 High Point, NC 27265 336-294-5233 www.americandrew.com F C D OUTILLAGE NECESSAIRE: Clé (A) (fournie) Clé Alène (E) (fournie) Tournevis Cruciforme (non fourni) E Schéma 2 Schéma 1 E AVANT DE COMMENCER: G C D 1. Vérifier que les pièces correspondent à la liste, et qu’aucune ne manque. 2. Assembler votre meuble sur une surface lisse afin d’éviter toute égratignure du vernis. 3. ATTENTION: Ne pas serrer les écrous trop fort lors de l’assemblage. 4. Les vis, boulons et écrous de votre meuble peuvent avoir besoin d’être resserés de temps à autres. D C B A Schéma 3 INSTRUCTIONS: 1. Fixer l’Assise à la patte arrière avec deux Vis (G) prémunies d’une Rondelle d’Arrêt (C) et d’une Rondelle Plate (D). Serrer avec la Clé Alène (E). Voir Schéma 1. 2. Fixer l’Assise au Dossier avec une Vis (F) prémunie d’une Rondelle d’Arrêt (C) et d’une Rondelle Plate (D). Serrer avec la Clé Alène (E). Voir Schéma 2. 3. Fixer l’Assise aux pattes avant en mettant sur chacune des vis des pattes, une Rondelle Plate (D), une Rondelle d’Arrêt (C) puis un Ecrou (B). Laisser les Ecrous (B) laches. Voir Schéma 3. 4. Placer les barres de côté entre les pattes avant et arrière et les fixer avec deux Vis à Bois (H) chacune. Voir Schéma 4. 5. Placer la barre de devant entre les pattes avant et la fixer avec deux Vis à Bois (H). Voir Schéma 5. 6. Serrer les Vis et Boulons, avant d’utiliser votre chaise. H Barre Avant Barre de Côté QUINCAILLERIE No. PIECE DESCRIPTION Qté A Clé 1 B Ecrou 5/16” 4 C Rondelle d’Arrêt 5/16” 9 D Rondelle Plate 5/16” 9 E Clé Alène 5/16” 1 F Vis 5/16” x 1-1/2” 1 G H Vis 5/16” x 3” 4 Vis à Bois 1-1/4” 6 Schéma 4 Merci pour avoir acheté votre meuble chez american drew drew ® american HOJA DE INSTRUCCIONES 079 - 690 4310 Regency Drive, Suite 101 High Point, NC 27265 336-294-5233 www.americandrew.com E F C D HERRAMIENTA NECESARIA: Jalón (A) (incluido) Jalón Allen (E) (incluido) Destornillador Phillips (non proveado) Figura 2 E G C D Figura 1 ANTES DE EMPEZAR: 1. Compruebe las partes en contra de la lista de piezas para asegurarse que todos los elementos están en el cartón. 2. Montar los muebles sobre una superficie limpia y plana para evitar evitar daños. 3. CAUTELA: no apriye demasiado los tornillos, tuercas y pernos, durante el montaje. 4. Sus muebles pueden requerir apretar de vez en cuando. INSTRUCCIONES: 1. Sujetar el Asiento a la pata detrás con dos Tornillos (G) antemano colocados con una Arandela de Parada (C) y una Arandela Plana (D). Apretar con el Jalón Allen (E). Veía Figura 1. 2. Sujetar el Asiento al Respaldo con un Tornillo (F) antemano colocado con una Arandela de Parada (C) y una Arandela Plana (D). Apretar con el Jalón Allen (E). Veía Figura 2. 3. Sujetar el Asiento a las patas delante con una Arandela Plana (D), una Arandela de Parada (C) y una Tuerca (B). Dejar las Tuercas (B) flojas. Veía Figura 3. 4. Instalar las varas entre las patas detrás y las patas delante, con dos Tornillos para Madera (H), para cada una. Veía Figura 4. 5. Instalar la vara de delante entre las patas delante, con dos Tornillos para Madera (H). Veía Figura 5. 6. Apretar todos los Tornillos y Tuercas antes de sentarse. D C B A Figura 3 H Vara de Delante Vara de Lado FERRETERIA No. PARTE DESCRIPCION Ctd A Jalón 1 B Tuerca 5/16” 4 C Arandela Parada 5/16” 9 D Arandela Plana 5/16” 9 E Jalón Allen 5/16” 1 F Tornillo 5/16” x 1-1/2” 1 G H Tornillo 5/16” x 3” 4 Tornillo Madera 1-1/4” 6 Figura 4 ¡Gracias por comprar muebles hechos por american drew!