ESPECIFICACIONES CARACTERISTICAS Exactitud
Transcripción
ESPECIFICACIONES CARACTERISTICAS Exactitud
ESPECIFICACIONES CARACTERISTICAS APROBACIONES Exactitud: ±0.15% del Span (Salida 3-15 &1-17 PSI). ±0.25% del Span (Salida 3-27 & 6-30 PSI). Repetibilidad: 0.05% del Span Banda Muerta: 0.02% del Span. Estabilidad: 0.5% del Span por 6 Meses. Capacidad de Salida-Standard.4.0 SCFM (Alimentación y venteo son balanceadas dentro del +/- 1 %). Modelo alta presión: 4-8 SCFM (dependiendo del tamaño de tubo de alimentación) Factory Mutual Intrinsically Safe: STD5000 & 6000 I/P 4-20mA Models Only · Intrinsically safe operation for Class1, II, and III, Div.1, applicable Groups A, B, C, D, E, F, G. · Nonincendive for Class 1, Division 2, Groups A, B, C, D. · Suitable for Class lI, Div. 2 Groups F, G. · Suitable for Class lII, Division 2. Hazardous Locations Outdoors, NEMA 4X when installed par Brandt I.S. lnstallation Drawing · (See lnstallation Manual MA45-5600-00). Explosion Proof · Explosion Proof for Class 1, Div. 1 & 2, Applicable Groups B, C, D Hazardous Locations Outdoors, NEMA 4X. · Dust lgnition proof for Class lI, Div. 1 & 2, Applicable Groups E, F, G Hazardous Locations Outdoors, NEMA 4X. Consumo de Aire: 0.04 SCFM promedio (0.06 SCFM Máximo). ESPECIFICACIONES FUNCIONALES Efectos de Posición : No Medible Efectos de Vibración: < 0.25% de 1-200 Hz/lg Frecuencia:-3db at 5 Hz (195 ohm a 20 mA) Carga: 3.8 VDC + 5 ohm (195 ohm a 20 mA) Corriente : 3.7mA min, 200 mA max. Presión de aire de alimentación: Standard. Mínimo de 3 psig y Máximo de10 psig por sobre la máxima salida calibrada Alta Presión: Salidas de 3-15 PSIG es de 35 a 100 psig ó 2.4 a 6.9 Bar. (Presión por debajo de 35 psi puede afectar la salida de la unidad). Aire: Limpio, Seco y libre de aceite. Temperatura: -40 a 150 ºF (-40 a 66 ºC) EMI/RFI: Efecto Menor al ± 1% sobre el cero/ span cuando se instala de acuerdo a las guías de instalación. Modos de Operación: Directa, Reversa, y/o Rango Partido, seleccionable en campo. (Ver notas en la selección del modelo) Modo de Falla: Directo mecánicamente, independientemente de la selección Directa ó Inversa. ESPECIFICACIONES FISICAS Cubierta: NEMA 4X 1 IP65 Purgada internamente Aluminio maquinado con cobertura protectora de epoxy. Conexiones: Puerta de alimentación: 1/4" NPTF (IX) Puerta de Salida: 1/4'' NPTF (2X) Eléctrica: 1/2'' NPTF conduit (2X). Terminales: Para cable 12- 22 AWG Peso: 2.5 libras Canadian Standard Association lntrinsically Safe: STD5000 & 6000 I/P, · lntrinsically Safe: Class 1, Groups A, B and Class lI, Groups E, F, G and Class IIl. Temp Code T3C, Intrinsically Safe when connected to CSA cartified safety barriers rated 31.5 V max., 463 ohms min. CSA.ENC.4 outdoors lntrinsically Safe: Class 1, Groups C, D and Class lI, Groups E, F, G, and Class lII. Temp Code T3C, lntrinsically Safe when connected to CSA certified safety barriers rated 28V max., 120 ohms rnin. CSA.ENC.4 outdoors · Class 1, Division 2, Groups A, B, C, D. without safety barriera CSA.ENC.4 Outdoors Explosion Proof: All Models · Explosion Proof for Class 1, Groups B, C, D; Class 1 1, Groups E, F, G; Class 111 and Class 1, Div. 2, Groups A, B, C, D Hazardous locations Outdoors CENELEC & Sira Intrinsically Safe: STD5000 & 6000 l/P, · Approved for Intrinsically Safe Operation and complies with the harmonized European Standards EN50 014 (1977) & ENSO 020 (1977) · Category: EEx ia IIC T4 Tarnb = 60'C · Certificate No:Ex 93C2032X · Umax = 3OVdc, lmax = IGOMA, Ceq = 0.94nF, Leq = 7.0 uH, Pmax 0.75W Flame Proof: STD6000 I/P, All Models · CENELEC/Sira approved for Flame Proof installations under harrnonized European Standards BS ENSO 01 4:1992 and BS EN 50 01 8:1994. · Category: EEx d l IC T6 · Certificate No. Ex98EI 1 21 X Pi 0.7W European Community "CE" · The STD5000and STD6000 Series I/P's have been tested and found to comply with BS ENSO081-2:1993 General Emissions, Residential, Commercial and Light Industrial and BS ENSO0822:1995 Generic Inmunity, Residential, Commercial and Light Industrial. IMPORTANT: Before installation refer to Brandt installation & instruction manual MA45-5600- 00. All wiring and installations must be made in accordance with all local and national codes appropriate to the are in which the instrument is to be installed.