Duotour DTAS / DTAT - Boon Edam Australia
Transcripción
Duotour DTAS / DTAT - Boon Edam Australia
Instructioncard Doutour DTAS/DTAT Duotour DTAS / DTAT L o c k i n g d e vi c e s 1 Interated electromagnetic lock (fail-safe) 2 Electromechanical lock (bi-stable)* Safety - and users instr uctions Contr ol panel T ouch screen dis play Locking dev ices Maintenance Cleaning instr uction O per ating limitation Ex planation of the sy mbols 3 Mechanical lock.* Ma i n t e n a n c e Weekly : Monthly : • • • • • • • Yearly : • Check daily : Emergency-, safety devices and general operation of the door. Presence of loose parts, sharp edges or broken glass. Safety and contrasting stickers are applied. Lighting; to provide a proper level of illumination inside the door. Floor condition; avoid slipping or tripping hazards and excessive dirt inside the door. Clean the anodised, powder coated and/or stainless steel surfaces with a wet cloth. Clean the anodised, powder coated and/or stainless steel surfaces with a wet cloth and a non-aggressive soap. Stainless steel surfaces need to be cleaned according the instruction below, Vacuum clean all the brushes. The door needs a major maintenance check once a year. This has to be done by Boon Edam or an approved agent. This applies as well for repairs. Outside Inside Doorset stops. 40 sec. Doorset rotates on normal speed. Note : • + Doorset rotates on slow speed. Make sure maintenance is properly recorded in the Logbook inside the door. 1x Doorset rotates into restposition. Caution ! Uninteruptable Power Supply activated (UPS). After 30 min. one programmable last action. No power supply. • Don’t use water near the drive-units or control boxes. Doorset does not rotate. • Switch OFF the power supply of the door during maintenance or other work. Sliding doors movement will be stopped. Disabled pushbutton. Sliding doors movement. Acoustic signal. Warning ! Cl e a n i n g I n s t ru c t i o n Sensors : Doorset rotates slow during 40 seconds. • Stainless steel parts: • • Remove dirt and dust with a wet cloth and dry with a clean soft cloth. Avoid scratching!! Use sponge to wipe the parts clean and dry with a clean cloth. Apply an even spray Inno-x on the surface to be treated or spray it on a clean, dry and soft cloth and apply. Rub off with a clean, dry and soft cloth. Emergency pushbutton. Optional / CE Plus. Extra country specific. Warning : Opera t i n g l i m i t a t i o n Do not use the door when the wind force at the entrance exceeds the Beaufort value as indicated in the table below. To prevent damage or injuries make sure the door is switched off and locked. Diameter 3.6 - 4.2 meter Diameter 4.8 - 5.4 meter 11 Bft. 10 Bft. Boon Edam B.V. P.O.Box 40, 1135 ZG Edam Holland. • Any children or minors using the product must be supervised by a responsible adult. • This product should not be considered as a playground. Do not let children play inside or near the door. • Running or dashing into a closing door are prohibited. • In case of broken glass do not use the door. Take all necessary precautions to avoid people coming into contact with sharp edges of the broken glass. Version : 2015/01/12 Edition : DTAS/DTAT-INS-UK Duotour DTAS/DTAT Saf e t y- a n d u s e rs i n s t r u c t i o n s A. Duotour safety devices 10 Showcase Boon Sensor (SBS).** 1 Safety Rail Bent wall (SRB). Contr ol panel C. The working principle of the Duotour 1 Night mode. 1 Night mode. 2 Sliding mode. 2 End Buffer Sensor (EBS). 3 Revolving mode. 2 Revolving mode / continuously slow. 11 End Style Sensor (ESS).** 4 Continuously slow / inand outgoing traffic (AUTOMATIC). 3 Horizontal Boon Sensor (HBS slow). 5 Restposition 1 (winter) / sliding doors open (OPEN). 3 Revolving mode / restposition 2 (summer). B. The sliding doors safety devices 1 Reverse mechanism. 6 Restposition 2 (summer) / outgoing traffic (EXIT). T ouch scr een display 4 Horizontal Boon Sensor (HBS stop). A. Monitoring 4 Revolving mode / restposition 1 (winter). 1 2 2 Stop mechanism. Selected operating mode, sensor activations failures are displayed on the touch screen. B. Advanced settings 1 5 Safety Rail Turning wall (SRT). 1 Log in: code 7410+ENT. 5 Sliding mode / in- and outgoing traffic. 2 3 Reversing safety (HBS slow). Operation Settings Log in Contact info. 6 Emergency pushbutton inside (outside*). 1 2 6 Sliding mode / outgoing traffic. Main E S C Operation A C Log in D E L E N T Settings Contact info. Log out 2 Lighting control: set timer. Main 1 789 456 123 0. + / - 4 Reversing safety (Threshold Safety THS). 7 Disabled pushbutton.* 0 Main 7 Sliding mode / open. Light setting Light switching Transport When door on Lighting off between Lighting During turning Version Use clock User settings Operation Sliding door Settings Log in External Contact info. Log out 2 Back 5 Reversing safety (Side Wing Safety SWS).** Back 3 Sliding door function: reduced width. Main 8 Anti Lockup Button. 40 sec. D. Emergency power operation* User settings Operation Sliding door Settings Transport Log in Lighting Sliding door settings Reduced width Version Contact info. Log out Back + 9 Top Rail Sensor (TRS).** 1x 30 min. E. Emergency open function (not suitable as escape route)* EMERGENCY 4 Transport settings.* Main User settings Operation Sliding door Settings Transport Log in Lighting Version OPEN Contact info. Version : 2015/01/12 Edition : DTAS/DTAT-INS-UK Transport settings Activate delay 0.1 sec. 456 Duration 0.1 sec. 456 Forced resume Back 1x Back Back 56:56 and 56:56 Adjust clock 56:56 Back
Documentos relacionados
Duotour DTAC - Boon Edam Australia
Emergency-, safety devices and general operation of the door. Presence of loose parts, sharp edges or broken glass. Safety and contrasting stickers are applied. Lighting; to provide a proper level ...
Más detalles