Summit
Transcripción
Summit
Summit Wet/Dry Vacuum Section II Parts and Service Manual Order Parts Here: www.ivie-ent.com/parts Ph:(918)254-5161 (78495B) CLARKE TECHNOLOGY Summit Wet/Dry Vacuum 115 Volt Connection Diagram 1/98 Page -18- CLARKE TECHNOLOGY Summit Operator's Manual CLARKE TECHNOLOGY Wand and Tool Kit #16414A 8-94 7 8 5 2 1 3 4 6 2 15 14 16 17 18 9 13 11 10 12 Ref. 1 2 3 4 5 6 7 8 9 Part No. 19200A 39200A 31207A 38500A 19501A 636706 68701A 674114 39201A Description Carpet Tool Assembly Floor Tool Bumper Carpet Shoe Lower Wand Assembly Disconnect Pin Upper Wand Vacuum Hose Crevice Tool CLARKE TECHNOLOGY Summit Operator's Manual Qty 1 1 1 1 1 1 1 1 1 Ref. 10 11 12 13 14 15 16 17 18 Part No. 19203A 35206A 60713A 39202B 19202A 31207A 38503A 30901A 38502A Description 3" Dusting Tool Housing Bristle Upholstery Tool Squeegee Tool Assembly Bumper Rear Squeegee Shoe Squeegee Blade Front Squeegee Shoe Qty 1 1 1 1 1 1 1 1 1 Page -19- CLARKE TECHNOLOGY Summit Wet/Dry Vacuum Assembly Drawing 9/00 1 2 3 4 5 6 9 10 56 7 11 54 12 8 55 53 5 52 13 14 15 16 17 18 51 44 19 7 48 41 50 45 47 43 49 20 42 7 40 46 39 38 21 22 37 36 7 35 36 34 33 23 32 30 29 Page -20- 24 28 27 26 25 CLARKE TECHNOLOGY Summit Operator's Manual 1u u 2 3 4 5u 6 7 8 9 10 11 u 12 13 13 13u 13 14 NOTE: uindicates a change has taken place since last publication of this manual 15 16 17 18 19 20 21u 22 23 u 24 25 26 27 28 29 30 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 Part No. 42186B 11675A 58013A 66966A 170686 47711A 911933 85397A 674110 32381C 30004A 47316B 962950 85728A 653407 54359A 44906A 51401A 44907A 40813A 44911A 40812A 44914A 40813A 58534A 58533A 34208B 628520 85600A 693406 690212 673416 63055B 55713A 38973C 38976D 68664A 692472 85737A 85738A 69433A 920346 59947A 167308 60506A 85702A 30423A 832002 839401 833407 833901 692409 34807C 66969A 33804A 35230C 35234C 69087A 69517A 34274A 733442 73713B 930093 980646 818180 699202 46739A 69894A 49310A Description Power Cord 115V 1 Power Cord Asm. 230V Includes/w Item2) 1 Strain Relief 1 Retainer, Strain Relief 1 Locknut, ½ Conduit 1 Terminal, .25 FIFQD 4 Terminal, #10 Ring 1 Screw, 10-24 x 3/8 SS 13 Hose 1 Cover, Motor Summit 12 1 Cover, Motor Summit 16 1 Switch, Rocker On/Off 1 Screw, ¼-20 x 3 3 Screw, ¼-20 x 4 Gasket 1 Gasket 1 Vac Motor 2 STG. 115V 1 Carbon Brushes 2 Vac Motor 2 STG. 230V 1 Carbon Brushes 2 Vac Motor 3 STG. 115V Carbon Brushes Vac Motor 3 STG. 230V Carbon Brushes Spacer, 2 STG. 3 Spacer, 3 STG. Gasket, Vac Motor 1 Screen, Vac Motor 1 Screw, ¼-20 x 3/4 3 Gasket, Intake 1 Adapter, Intake 1 Gasket 1 Filter, Bag Asm. 1 Latch, Spring 2 Tank, 12 Gallon 1 Tank, 16 Gallon 1 Plate, Base 1 Caster, Front Swivel 1 Screw, ¼-20 x 5/8 S.S. 4 Screw, 5/16-18 x 5/8 S.S. 6 Bracket, Axle 2 Palnut, ½" 2 Wheel, 10" x 1.75 2 Snap Ring ½" 2 Axle, Shaft 1 Screw, ¼-20 x 13/4 4 Drain Hose 1 Clamp, Hose 2 Drain Valve 1 Drain Gasket 1 Drain Handle 1 Chain 1 Handle, Transport 1 Retainer, Float 1 Float 1 Housing, Motor Support 1 Housing, Motor Support Screen, Filter 1 Support, Filter Bag 1 Gasket 1 Gasket 1 Warning Plate 1 Rivet 4 Washer 7 Sleeve 1 Wire Tie 1 Filter 230V 1 Bracket 230V 1 Wire Assembly 230V 2 CLARKE TECHNOLOGY Summit Operator's Manual Highpower Ref. Standard CLARKE TECHNOLOGY Summit Wet/Dry Vacuum Assembly Parts List 9/00 1 1 1 1 1 4 1 13 1 1 1 1 3 1 2 1 2 3 2 1 3 1 1 1 1 2 1 1 1 1 4 6 2 2 2 2 1 4 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 4 7 1 1 1 1 2 Page -21- CLARKE TECHNOLOGY Summit Wet/Dry Vacuum Squeegee Assembly (14605A) Drawing and Parts List 9\00 1 2 3 4 5 6 7 8 18 17 9 16 11 15 14 17 12 NOTE: uindicates a change has taken place since last publication of this manual Ref. 1 2 3 4 5 6 7 8 Page -22- Part No. 66407A 69513A 69514A 30424A 960953 419702 55535A 63425A Description Pedal, SQ. Lift Support, Pedal Left Support, Lift Hose, Vac SQ. Bolt, Shoulder 3/8 x1 Wheel Knob Frame Weldment, SQ. Qty 1 1 1 1 2 2 2 1 (Instruction Sheet 78552A Rev.A) Ref. 9 11 12 14 15 16 17 18 Part No. 30940A 66963A 85383A 65434A 960952 980645 81112Au 69512A Description Blade, SQ. Retainer, SQ. Blade Screw 10-32 x 3/4 Lift, Weldment SQ. Bolt, Shoulder 3/8 x 3/8 Washer SS Nut, 5/16-18 Support, Pedal Right Qty 2 2 16 1 6 6 8 1 CLARKE TECHNOLOGY Summit Operator's Manual SQUEEGEE ASSEMBLY INSTALLATION For Summit Wet/Dry Vacuum squeegee assembly (14605A) installation follow this procedure: 1. Remove the head assembly from tank. 2. Turn the handle and tank upside down. 3. Remove the axle brackets. Leave axle and wheels in position. Attach the right and left pedal supports, (ref. #18 and #2 - page 18) using the same bolts. 4. Remove the two bolts that secure the base plate. Use the bolts to secure the lift support, (ref. #3 page 18) and the base plate. 5. Attach squeegee lift weldment with shoulder bolts provided (ref. #14 and #15 - page 18). 6. Turn the handle and tank over to the upright position with the wheels on the floor. 7. Attach the squeegee assembly to the squeegee lift weldment, (ref. #14 and #8 - page 18) and tighten clamping knobs (ref. #7 - page 18). 8. Attach the straight hose cuff to the squeegee. 9. Replace the head assembly on the tank (Do not use the filter bag for wet pickup). Attach 90° cuff to inlet. To Operate: 1. To raise squeegee, push down on pedal (ref. # 1 page 18) 2. To lower squeegee, push forward on pedal. The squeegee will operate both forward and backwards. SUJECION DEL CONJUNTO DE LA BAYETA Para colocar el conjunto de la bayeta en el modelo SUMMIT agua y polvo (14615A), siga el procedimiento siguiente, refiriéndose a la página ... : 7. Fije el conjunto de la bayeta en la placa soldada del brazo de levantamiento (N ref. 14 y 8) y aprete los pernos de las uñas. 1. Saque el conjunto de la cabeza de aspiración. 8. 2. Gire el mango y vuelque el depósito. Fije el manguito derecho del flexible sobre la bayeta. 3. Tire los soportes del eje. Deje el eje y las ruedas en su sitio. Fije los soportes izquierdo y derecho del pedal (N ref. 18 y 2) con los mismos pernos. 9. Coloque de nuevo la cabeza de aspiración sobre el depósito. (No use la bolsa-filtro para aspirar el agua). Fije el manguito acodado en ángulo recto sobre la abertura. 4. Quite los pernos de sujeción de la placa de base. Use estos pernos para fijar el soporte de levantamiento (N ref. 3) en la placa de base. 5. 6. Fije la placa soldada del brazo de levantamiento de la bayeta con los pernos de apoyo suministrados (N ref. 14 y 15). Gire el mando y vuelque el depósito en posición vertical, con las ruedas puestas en el suelo. Funcionamiento de la bayeta: 1. Para levantar la bayeta, presione el pedal (N ref. 1) 2. Para bajar la bayeta, empuje el pedal hacia la parte delantera. La bayeta funciona en marcha adelante y atrás. FIXATION DE L'ENSEMBLE DU SUCEUR Pour le placement de l'ensemble du suceur sur le modèle SUMMIT eau et poussières (14615A), veuillez appliquer la procédure suivante en vous référant à la page ...: 1. Déposez l'ensemble de la tête d'aspiration. 2. Tournez la poignée et faites basculer le réservoir. 3. Enlevez les supports de l'axe. Laissez l'axe et les roues en place. Fixez les supports gauche et droit de la pédale (N réf. 18 et 2) en utilisant les mêmes boulons. 4. Enlevez les boulons de fixation de la plaque de base. Utilisez ces boulons pour fixer le support de relevage (N réf. 3) à la plaque de base. 5. 6. Fixez la plaque soudée du bras de relevage du suceur avec les boulons à embase fournis (N réf. 14 et 15). Tournez la poignée et faites basculer le réservoir en position verticale, les roues posées sur le sol. CLARKE TECHNOLOGY Summit Operator's Manual 7. Fixez l'ensemble du suceur sur la plaque de soudure du bras de relevage. (N réf. 14 et 8) et serrez les boutons des griffes. 8. Fixez le manchon droit du flexible sur le suceur. 9. Replacez la tête d'aspiration sur le réservoir. (N'utilisez pas le sac-filtre pour une aspiration d'eau). Fixez le manchon coudé en angle droit sur l'orifice. Fonctionnement du suceur: 1. Pour relever le suceur, appuyer sur la pédale (N réf.1) 2. Pour abaisser le suceur, pousser la pédale vers l'avant. Le suceur fonctionne en marche avant et en marche arrière. Page -23- CLARKE TECHNOLOGY Summit Wet/Dry Vacuum Electrical Schematic 1/98 Page -24- CLARKE TECHNOLOGY Summit Operator's Manual CLARKE TECHNOLOGY Summit Wet/Dry Vacuum 230 Volt Connection Diagram 1/98 CLARKE TECHNOLOGY Summit Operator's Manual Page -25-