n DS-100 Premium Diesel Fuel Additive
Transcripción
n DS-100 Premium Diesel Fuel Additive
Liber and o n ó i cc al M i r undo de la F DS-100 Premium Diesel Fuel Additive DS-100 Aditivo Multifuncional para Combustible Diesel Tratamiento multifuncional detergente/dispersante para combustible diesel. Aplicación: DS-100 es un aditivo multifuncional diseñado con la química más avanzada para mejorar la calidad y optimizar el rendimiento de los combustibles diesel. DS-100 contiene mejoradores de libricidad para aumentar las propiedades lubricantes de los combustibles bajos en azufre. El rango ó tasa de tratamiento sugerido para este producto es la siguiente: Nivel Alto: 240 ppm w/w (70 ptb) Nivel Medio: 180 ppm w/w (52.5 ptb) Nivel Bajo: 150 ppm w/w (43.5 ptb) Caracteristicas Fisicas: PUNTO DE INFLAMACIÓN, C, PMCC 62 LBS POR U.S. GAL @ 15.6 oC 7.60 LBS POR IMP GAL @ 15.6 oC 9.13 PUNTO DE GOTEO, oC -36 GRAVEDAD ESPECIFICA @ 15.6 oC 0.912 VISCOSIDAD @ 40 oC, CST 43 Características Químicas: % Peso mínimo, % Peso máximo típico NITROGENO 0.99 1.10 1.21 Beneficios: Cuando se utiliza a la taza recomendada, DS-100 ayuda a los combustibles diesel a alcanzar los requerimientos del Consejo Nacional de Pesos y Medidas (NCWM), la Asociación del fabricante del motor (EMA) y del carro Consejo del Mantenimiento de Camiones (TMC), para: • Limpieza de inyectores, medida por: › Cummins L10 Injector Depositing Test (Keep Clean) › Peugeot XUD9 Test (Keep Clean) • Mejora de la estabilidad térmica de combustible en almacenamiento. • Mejora la lubricidad para extender la vida de los componentes del sistema de combustible. • Dispersante de gomas insolubles. • Protección contra la corrosión. Quechem, Div of Gra flo Inc. P.O.BOX 64 Green Valley, Ontario, Canada, K0C 1L0 PANAMÁ: (507) 390-5850 Email: Telf: Fax: Email: Website: 1-613-525-5858 1-613-525-5883 [email protected] www.quechem.com [email protected] Liber and o n ó i cc al M i r undo de la F *Prevention of formation of stable fuel-water emulsions Additionally, fuels containing DS-100 additive at the higher treat rates demonstrate: Multiple Cummins L10 Injector Depositing Test (Keep Clean) Passes Multiple Peugeot XUD9 Test (Keep Clean) Passes Cummins L10 Injector Depositing Test Clean Up Cummins L10 Steady State Clean Up Peugeot XUD9 Clean Up Fuel Economy Improvement Reduced Exhaust Emissions Unloading, storage and blending instructions: General handling instructions - In general, Quechem recommends, as a minimum, the use of neoprene or nitrile rubber gloves and safety glasses or chemical splash goggles. The Material Safety Data Sheet should be consulted for specific information and for information on health and safety when handling this product. Fire and explosion hazard data: Flash Point (method) Classification 62 oC PMCC Combustible Temperature recommendations: Unloading Pumping temperature Ambient oC oF Maximum temperature* 45oC 113oF Storage Maximum temperature for long-term storage 45oC 113oF Blending Maximum base oil temperature for 45oC 113oF mechanical or in-line mixing Equipment recommendations: Type of pump Positive Displacement Type of transfer lineBall Launched, Insulated Transfer line size 2-3inch/5-8 cm. Quechem, Div of Gra flo Inc. P.O.BOX 64 Green Valley, Ontario, Canada, K0C 1L0 PANAMÁ: (507) 390-5850 Email: Telf: Fax: Email: Website: 1-613-525-5858 1-613-525-5883 [email protected] www.quechem.com [email protected] Liber and o n ó i cc al M i r undo de la F Heat source: Type n/a Storage tank n/a Viscosity data: cSt SUS at 0°C,32°F 259 1196 at 25°C,77°F 76 352 at 40°C,104°F 43 201 Notes: Pour Point -36°C,-32°F Low Flash Point- Use caution when handling this material Additional recommendations: Holding the material in excess of this temperature may cause chemical degradation. Use steam for heating and tracing only when the material is in motion to avoid localized overheating. Cold Temperature Storage - If product has been stored below its pour point temperature it should be heated to 21°C/70°F before using. Equipment recommendations: Type of pump Positive Displacement Type of transfer lineBall Launched, Insulated Transfer line size 2-3inch/5-8 cm. Typical properties, whereas stated, are to be considered as representative of current production and should not be treated as specifications. While all the information presented in this document is believed to be reliable and to represent the best available data on the products, NO GUARANTEE, WARRANTY, OR REPRESENTATIONS IS MADE, INTENDED, OR IMPLIED AS TO THE CORRECTNESS OR SUFFICIENCY OF ANY INFORMATION, OR AS TO THE SUITABILITY OF ANY CHEMICAL COMPOUNDS FOR ANY PARTICULAR USE, OR THAT ANY CHEMICAL COMPOUNDS OR USE THEREOF ARE NOT SUBJECT TO A CLAIM BY A THIRD PARTY FOR INFRINGEMENT OF ANY PATENT OR OTHER INTELLECTUAL PROPERTY RIGHT. EACH USER SHOULD CONDUCT A SUFFICIENT INVESTIGATION TO ESTABLISH THE SUITABILITY OF ANY PRODUCT FOR ITS INTENDED USE. Products may be toxic and require special precautions in handling. For all products listed, user should obtain detailed information on toxicity, together with proper shipping, handling, and storage procedures, and comply with all applicable safety and environmental standards. Quechem, Div of Gra flo Inc. P.O.BOX 64 Green Valley, Ontario, Canada, K0C 1L0 PANAMÁ: (507) 390-5850 Email: Telf: Fax: Email: Website: 1-613-525-5858 1-613-525-5883 [email protected] www.quechem.com [email protected]