70478 LED Driver

Installation Instructions
70478 LED Driver
WARNING - PLEASE READ ALL
INSTRUCTIONS PRIOR TO INSTALLATION
CONNECTION
Refer to the wiring diagrams provided for accurate wire connections.
The Red(+) wire is the Positive lead wire. The Black(-) wire is the
Negative lead wire.
WARNING – PLEASE READ ALL INSTRUCTIONS PRIOR TO
INSTALLATION
READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS BEFORE
INSTALLING OR MAINTAINING THIS PRODUCT.
TURN OFF POWER PRIOR TO ANY WORK ON THE SYSTEM
OR PRODUCT
120V TAP CONNECTION
WHITE
FEED
BLACK
FEED
277V TAP CONNECTION
COM PRI
120VAC PRI
POWER
UNITS
Output:
DC 24V
70478 series class 2 LED Driver must be installed in a well-ventilated area free
from explosive gases and vapors. Proper operation requires the free flow of
air. As this transformer is hard-wired, it should only be installed by a qualified
electrician.
CHARACTERISTICS:
Installing, wiring, and maintenance must be done by qualified persons or a
certified electrician in accordance with all local and National Electrical Codes.
• Thermal protection.
Warranty is voided in case of unauthorized modifications and/or improper use.
Save these instructions and refer to them when additions, changes, or services
to the system are made.
COM PRI
BLACK
FEED
RED
POWER
UNITS
120VAC PRI
BLACK
277VAC PRI
DO NOT INSTALL DAMAGED PRODUCT
WHITE
FEED
RED
Output:
DC 24V
BLACK
277VAC PRI
• Constant voltage.
• Overlaod protection.
Red light on when overloaded.
Attention: Press restore button after loading back to normal.
Please observe voltage drop over long cable lengths.
ELECTRICAL RATINGS
Suitable for dry locations only.
Input
Model
INSTRUCTIONS FOR USE
1 Shut off power at the main breaker before attempting installation.
2 This Power units may be installed with a compatible 120V Magnetic Low
Voltage (MLV) dimmer switch.
Output
V
Hz
VDC
A
VA (Max.)
JCLD24A060BN
120/277
60
24
2.50
60
JCLD24A020BN
120/277
60
24
0.83
20
JCLD24A096BN
120/277
60
24
4.00
96
CONDUCTORS:
3 Compatible 3-way 120V MLV dimmers.
4 All direct wire connections to the Dimmable Driver must be secured inside
the built-in junction box.
5 A disconnect device shall be incorporated in the field wiring.
6 Installation work and electrical wiring shall be performed only by qualified
service personell in accordance with all applicable codes and standards,
including fire-rated construction.
Model
Input Conductors
AWG
Output Conductors
Temperature ºC (Min.) AWG (Min.) Temperature ºC (Min.)
JCLD24A060BN 12-18
60
16
75
JCLD24A020BN 12-18
60
18
60
JCLD24A096BN 12-18
60
16
60
MOUNTING
Locations for mounting must be able to support the weight of the Power units.
It is recommended to mount the Power units vertically with the wiring
compartment pointed downward.
N.E.C. requires all Power units to be grounded to the Green grounding wire.
KNOCKOUTS
Remove wiring knockouts as needed and install 1/2” Romex connectors or
bushings to reduce strain on wires.
One knockout is reserved for input voltage while the second knockout is
reserved for output voltage.
v.2.01.16
Ledra Brands Inc.
15774 Gateway Circle
Tustin, CA 92780
p:714.259.9959
f:714.259.9969
In a continuing effort to offer the best product possible we reserve the right to change, without
notice, specifications or materials that in our opinion will not alter the function of the product.
www.LedraBrands.com
IMPORTANT INFORMATION
WARNING
ADVERTENCIA
AVERTISSEMENT
• To avoid possible electrical shock, before
installing light fixtures, disconnect power
by turning off the circuit breakers and the
wall switch. Use appropriate lock out, tag
out procedures.
• Para evitar posibles choques eléctricos,
antes de instalar luminarios, desconecte
el alimentación apagando los
interruptores de circuito y el interruptor
de pared. Use adecuado procedimientos
de bloqueo y etiquetas.
• Pour éviter les chocs électriques, avant
d’installer des appareils d’éclairage,
coupez l’alimentation en désactivant
les disjoncteurs et l’interrupteur mural.
Utilisation appropriée est bloquée, balise
les procédures.
• Compruebe que el voltaje de
alimentación es correcto comparándolo
con la información de etiqueta de el
luminario.
• Assurez-vous que la tension d’alimentation
est correcte en comparant les informations
d’étiquette de luminaire.
• Ensure that supply voltage is correct by
comparing readings to the luminaire label
information.
• Make all electrical and grounding
connections in accordance with the
National Electrical Code (NEC) and any
applicable local code requirements.
• Allow sufficient time for fixture and lamp
to cool before servicing.
• Hacer todas las conexiones eléctricas y
puesta a tierra de acuerdo con el código
eléctrico nacional (NEC) y los requisitos
del código local aplicable.
• Permite suficiente tiempo para enfriar el
luminario y la lampara antes de empesar
servicio.
CAUTION
PRECAUCION
• Wiring must be done in accordance with
national and local electrical codes and
ANSI/NFPA 70.
• PPE Personal Protective Equipment such
as gloves and safety glasses should
be used at al times when installing,
maintaining, and servicing.
• Risk of fire. Keep combustible material
away from fixtures.
• Todo el cableado debe hacerse de
conformidad con los códigos eléctricos
nacionales y locales y ANSI/NFPA 70. Si
no está familiarizado con el cableado,
debe utilizar a un electricista certificado.
• Equipo de protección personal como
guantes y lentes de seguridad se debe
utilizar al instalar, mantener o reparar.
• Riesgo de incendio. Mantenga los
materiales combustibles lejos de los
liminarios.
v.2.01.16
Ledra Brands Inc.
15774 Gateway Circle
Tustin, CA 92780
p:714.259.9959
f:714.259.9969
• Faire tous les raccordements électriques
et mise à la terre selon le Code électrique
National (NEC) et des exigences du code
local applicable.
• Laisser suffisamment de temps pour
luminaire et lampe refroidir avant
l’entretien.
MIS EN GARDE
• Câblage doit être conforme aux codes
électriques locaux et nationaux et ANSI/
NFPA 70..
• Tout le câblage doit être effectué par un
électricien certifié.
• Risque d’incendie. Garder les matières
combustibles
loin de luminaires.
In a continuing effort to offer the best product possible we reserve the right to change, without
notice, specifications or materials that in our opinion will not alter the function of the product.
www.LedraBrands.com