Product Information

Transcripción

Product Information

Product Information
ENVIROBASE® High Performance Waterborne Basecoat
Product Description
Envirobase High Performance is a premium waterborne color system for use in repair and repainting of motor
vehicles. Industry leading color capability is easily achieved when applied as part of a two or three-stage basecoat/
clearcoat paint process. Mixed Envirobase High Performance color reproduces the original OEM solid, metallic,
mica, or XIRALLIC® paint finish of virtually all OEM manufacture's worldwide.
Envirobase High Performance products are engineered to reduce volatile organic compounds (VOC) and will
exceed all of today’s legislative VOC restrictions throughout the United States and Canada.
Envirobase High Performance waterborne color system is also capable of producing internal color as well as
interior color. For additional information, see Envirobase product bulletins EB145 for interior color and EB510 for
internal color.
Preparation of Substrate
Apply over original baked finishes or over recommended undercoats.
In all cases, wash all surfaces to be painted with soap and water. Final clean with an appropriate
waterborne cleaner. Ensure that the substrate is thoroughly cleaned and dried before starting
repair.
Apply Envirobase High Performance after sanding with European P800-P1200 / US 500-600
grade paper or dry sand with European P600-800 / US 500-600 grade paper.
Wash off residue and dry thoroughly before recleaning with appropriate waterborne substrate
cleaner. The use of a tack rag is recommended.
•
Before mixing, gently hand shake bottles of the Envirobase High Performance toners for a few seconds before
use. Do not place toners or mixed color on shaker or mechanically agitate.
•
Mixed Envirobase High Performance color should be thoroughly hand-stirred before application. If not used
immediately it should be hand-stirred again before use.
•
Use nylon 125 micron paint filters specially designed for use with waterborne paint materials.
© 2014 PPG Industries
EB-143 12/14
APPLICATION GUIDE:
Mixing Ratio:
Envirobase High Performance Color
T494/T595**
1 Part
10% by volume for solid color
20% by volume for metallic / pearl color
30% by volume for tinted mid-coat color
OR
T492 Adjuster*
1 Part
Envirobase High Performance Metallic / Pearl Color
T492 Adjuster*
T494/T595** Thinner
1 Part
+10% by volume for metallic / pearl color
Envirobase High Performance Tinted Mid Coat Color
T492 Adjuster*
T494/T595** Thinner
1 Part
+20% by volume for tinted mid-coat color
*T492 Adjuster has been specifically developed as an enhancement to the Envirobase High Performance basecoat system. Leading edge
parts such as bumpers and fascia’s or low profile front ends that may be prone to stone chipping or when driving in extreme conditions
such as abrasive gravel roads or when subjected to high powered pressure washing, the addition of T492 adjuster will improve the
basecoat film properties. Note: Application, flash off and drying is the same as with the standard process. If additional reduction is
required for viscosity adjustment, DO NOT add additional T492, use T494/T595 only.
** T595 is for use in high heat, low humidity conditions only. See thinner selection guide on page 6 for additional information.
Pot Life
Un-activated, 90 days stored in sealed plastic containers. If activated, pot life is 2 hours.
Hand stir well before using. Do Not mechanically shake.
Additives
T581 (optional activator) - 10% by volume after reducing. After activation, additional thinner may be
required to bring the color into the 23-28 second sprayable viscosity range.
Spraygun set up
Fluid Tip:
Spray Viscosity:
1.2 - 1.4 mm or equivalent
23 - 28 seconds, DIN4 @70°F (21°C)
HVLP at the air cap
Conventional at the spray gun
Color Coat
*
*
Spray Pressure
Control Coat
*
*
*Spray gun pressure will vary by manufacturer. See spray gun setup chart DOX440 on ppgrefinish.com
Envirobase / Technical Data Sheets & MSDS Index tab for manufacturer’s pressure information.
Number of Coats
All repairs:
2-3 coats to coverage plus control coat*
Horizontal surfaces may require two control coats where vertical surfaces will generaly only require one
control coat.
*Note: A control coat is not required for solid colors.
Flash Off
70°F (21°C)
Between Coats:
1-2 minutes or until dried to a matt finish
Final Flash-off:
When application is complete, apply the control coat and allow
it to dry naturally. Force drying of the control coat is not
necessary.
Note: Do not use the spray gun as an air drier. Use air drying equipment.
2
EB-143 12/14
APPLICATION GUIDE (cont’d):
Drying Times
Dust-Free
70°F (21°C)
Each coat approximately 2-4 minutes
Dry to Handle
70°F (21°C)
Approximately 15-20 minutes
Dry to De-Nib:
70°F (21°C)
Tape Time
70°F (21°C)
5 minutes
Dry to Clear
70°F (21°C)
15 minutes minimum
Note: Because of the intensity of IR curing, if the clearcoat is to be cured using IR the basecoat will first
need to be cured with IR to remove the residual moisture from the basecoat film.
Overcoat/Recoat
Overcoat with any compatible clear
Flash off until the entire surface is touch-dry and has a uniform
matt appearance, or for 15 minutes.*
Dry Sand
Use European P1500 / US 800 grit
Recoat
After 24 hours, 1 coat of Envirobase High Performance must be
applied prior to the clearcoat application. The maximum recoat
time is 48 hours.
*Temperature, humidity, air movement and film build affect dry times. The best results are achieved with
increased temperature and air movement with minimal film builds.
BLENDING / WET BED
Mixing Ratio:
T490 Tinted Clear Additive
T494 / T595* Thinner
4 Parts
1 Part
For use as a blending additive: Add up to 1 equal par t of the T490 mixtur e to 1 par t of r eady to spr ay
color and fade into the prepared blend panel.
or
For use as a wet bed: Apply 1 medium light coat of the T490 mixtur e to the blend panel and or the
entire repair panel and allow to dry. It will be milky blue when wet but will dry translucent. Once dry, apply
color. Be sure that whatever the wet bed material has been applied, it is completely covered with earlier
basecoat or clearcoat.
*T595 is for use in high heat, low humidity conditions only. See thinner selection guide on page 6 for additional information.
3 STAGE PEARL PROCESS
Mixing Ratio:
Ground Coat
Color
T492/T494/T595* Thinner
Pearl Coat
1 part
10%**
Color
1 part
20%**
**Note: Percentage by volume. If using T492 Adjuster, see page 2 for proper use.
* T595 is for use in high heat, low humidity conditions only. See thinner selection guide on page 6 for
additional information.
3
EB-143 12/14
3 STAGE PEARL PROCESS (cont’d):
Viscosity:
Viscosity &
Pot Life:
Pot Life:
23-28 seconds DIN4 at 70°F (21°C)
90 days stored in sealed plastic containers.
Always strain before use (nylon 125 micron is recommended).
Spray Gun &
Air Pressure
Fluid Tip:
1.2 - 1.4 mm
HVLP
Compliant
Color Coat
*
*
Control Coat
*
*
*Spray gun pressure will vary by manufacturer. See spray gun set up chart DOX440 on ppgrefinish.com Envirobase High Performance /
Technical Data Sheets & MSDS Index tab for manufacturer’s pressure information.
Application:
Ground Coat
•
•
•
•
•
Pearl Coat
Apply single coats until opacity is achieved.
Flash off thoroughly between coats.
Avoid heavy application and excessive film
builds.
Use air movement equipment to accelerate
drying as necessary. Choice of drying methods
will depend upon the type and size or the repair.
A control coat is not required for solid color
basecoats.
•
•
•
•
Horizontal and vertical surfaces
Apply single light coats based on color check
panels. Flash off thoroughly between coats.
Apply the control coat and allow it to dry
naturally.
Force drying of the control coat is not necessary.
The pearl color layer is not designed to give
opacity.
Flash Off:
Flash off until uniformly matt in appearance.
Dry Time:
Wait until ground coat is uniformly dry before
applying pearl coat
3 STAGE TINTED MID COAT PROCESS
Mixing Ratio:
Ground Coat
Color
Wait until pearl coat is uniformly dry before applying
clearcoat, approximately 15 minutes.
Tinted Mid Coat
1 part
20% **
Color
T492/T494/T595 Thinner
1 part
30%**
** Note: Percentage by volume. If using T492 Adjuster, see page 2 for proper use.
* T595 is for use in high heat, low humidity conditions only. See thinner selection guide on page 6 for additional information.
Viscosity &
Pot Life
Viscosity:
Pot Life:
90 days stored in sealed plastic containers
Always strain before use (nylon 125 micron is recommended)
Spray Gun &
Air Pressure
Fluid Tip:
1.2 - 1.4 mm*
HVLP
Compliant
Color Coat
*
*
Control Coat
*
*
4
EB-143 12/14
3 STAGE TINTED MID COAT PROCESS (cont’d):
Application:
Ground Coat
•
•
•
Tinted Mid Coat
Apply the control coat onto dry film for even
metallic appearance.
•
•
•
•
•
panels.
The mid coat layer is not designed to give
opacity.
Flash off the mid coat until it is uniformly dry
before applying clearcoat, approximately 15
minutes.
A control coat is not required for the tinted
midcoat layer.
Minor Repair Guidelines
Dirt nibs or other defects in the Envirobase High Performance paint film may be repaired as follows:
1.
2.
3.
4.
5.
Allow the surface to completely flash-off.
Dry sand the defect with P1500/US 800 grade paper or finer or with a fine abrasive pad or in combination with a small amount of SXA330 Wax and Grease
Remover as a sanding lubricant.
Remove sanding dust from the surface by strong air blowing with a clean air supply
Tack off surface with SX1070 tack rag.
Re-coat the surface with Envirobase High Performance as normal.
Compatibility
Low VOC Markets
National Rule Markets
Envirobase High Performance
ECP1x A-Chromatic Surfacer**
ECS2x A-Chromatic LV Sealer
EC530 En.V™ Performance Clearcoat
EC700 Series Clearcoats
EPW115 Waterborne Speed Prime
ECS6x A-Chromatic Sealer
EC530 En.V Performance Clearcoat
ONECHOICE®
SXA1031 Aerosol Etch* (cut throughs only)
SXA1050 Plastic Adhesion Primer**
SX1071 Etch Prime**
SX1005 Low VOC wax and Grease Remover
SWX350 H2O-SO-CLEAN™
Plastic Prep System*** (SU4901, SUA4903)
SU470LV 1K Compliant Adhesion Promoter
OneChoice
SX1057 Flexible 2K Surfacer
SX1060 Rollable 2K Primer Surfacer
Plastic Prep System*** (SU4901, SU4902, SU4903, SUA4903)
SWX350 H2O-So-Clean
GLOBAL REFINISH SYSTEM™
D8188
D8126
Global Refinish System
D820***
D800x*
D8099**
D8101
D8102
D8115
D8117
D8150
DELTRON®
DPLV305x
DPLV Epoxy
NCP280*
DCU2010
DC3010
DC4010
DC4125
Deltron
DPS305x*
DVLP Epoxy
K36
DCU2021
DCU2042
DCU2060
DCU2082
DC2000
DC3000
DC4000
DC4125
DX179x***
DPX801***
DPLF*
D8126
D8152
D893
D894
* For optimum performance a 2K primer or sealer may be used.
** For optimum performance a 2K sealer may be used.
*** Must be primed or sealed.
5
EB-143 12/14
Envirobase High Performance Waterborne Thinner Selection Guide
Note: Using T595 water bor ne thinner with humidity levels above 30% can cause extr emely slow flash and overall drying of the basecoat.
Do not blend waterborne thinners as this will affect overall basecoat performance. Use either T494 or T595 depending on humidity.
Health and Safety
See Material Safety Data Sheet and Labels for additional safety information and handling instructions.
•
•
•
•
•
•
•
•
The contents of this package may have to be blended with other components before the product can be used. Before opening the
packages, be sure you understand the warning messages on the labels and MSDS of all the components, since the mixture will have
the hazards of all its parts.
Improper handling and use, for example, poor spray technique, inadequate engineering controls and/or lack of proper Personal
Protective Equipment (PPE), may result in hazardous conditions or injury.
Follow spray equipment manufacturer’s instructions to prevent personal injury or fire.
Provide adequate ventilation for health and fire hazard control.
Follow company policy, product MSDS and respirator manufacturer’s recommendations for selection and proper sue of respiratory
protection. Be sure employees are adequately trained on the safe use of respirators per company and regulatory requirements.
Wear appropriate PPE such as eye and skin protection. In the event of injury, see first aid procedures on MSDS.
Always observe all applicable precautions and follow good safety and hygiene practices.
Equipment
Clean all mixing equipment immediately after use, preferably using a dedicated waterborne equipment cleaning machine with a final
rinse using waterborne thinner. Ensure all equipment is completely dry before storage or use.
Cleaning
Storage & Handling of Envirobase High Performance
• Envirobase High Performance tinters, Envirobase High Performance mixed color & waterborne thinner should be stored in a cool,
•
•
•
•
dry place away from sources of heat. During storage and transportation, temperature must be maintained at a minimum of 41°F or
+5°C or and a maximum of 120°F or 49°C. Avoid exposure to frost or freezing conditions.
Envirobase High Performance should be mixed in clean, dry plastic containers and equipment. Do not use mixing vessels or spray
equipment that contains solvent residues. Mixing vessels should ideally be plastic - if metal the container should be stainless steel or
have an internal anticorrosion coating.
Store waterborne & solvent borne wastes separately. A competent agent with appropriate certification must handle all waterborne
wastes. Waste must be disposed of in accordance with all Federal, State, Provincial and local laws and regulations.
Blended to spray basecoat color with T581 activator has a flash point above 200°F and may be disposed in the waterborne waste
stream intended for basecoat color (without activator). The waste disposal facility should be informed that the waste stream contains
isocyanates. T581 activator handled alone should be disposed in the solvent borne waste stream.
The Envirobase High performance waterborne paint residues should be segregated from all other wastes and kept in a separate
closed lined container. The Envirobase High Performance waterborne paint residues must be disposed or in accordance with all
Federal, State, Provincial and local laws and regulations.
6
EB-143 12/14
TECHNICAL DATA
Theoretical coverage (RTS), giving 12.7µm (0.5 mils) dry film thickness, 274-640 sq. ft. per US gallon.
Percent solids by volume RTS
8.5 - 20.0%
RTS Combinations
Color
Color : T494/T595
Color : T494/T595
Color : T494/T595
Color Coating
Color Coating
Color Coating
Color Coating
Ratio
Packaged
1 : 10%
1 : 20%
1 : 30%
Density (g/L)
991-1204
992-1186
992-1171
992-1156
Density (lbs./US gal.)
8.27-10.05
8.28-9.90
8.28-9.77
8.28-9.65
47-120
44-111
43-103
41-97
VOC Actual (lbs./ US gal.)
0.39-1.00
0.37-0.93
0.36-0.86
0.34-0.81
VOC Regulatory (g/L)
207-395
213-401
219-407
225-419
VOC Regulatory (lbs./US gal.)
1.73-3.30
1.78-3.35
1.83-3.40
1.88-3.50
Volatiles wt. %
60.42-84.97
63.42-86.29
66.01-87.44
68.26-88.40
Water wt. %
51.37-74.99
54.94-77.09
58.00-78.85
60.05-80.33
Exempt wt. %
0.0
0.0
0.0
0.0
Water vol. %
61.98-77.47
65.29-79.41
68.03-80.96
70.26-82.22
0.0
0.0
0.0
0.0
Color : T494/T595 :
T581
Color : T494/T595 :
T581
Color : T494/T595 :
T581
T490 : T494/T595
Color Coating
Color Coating
Color Coating
Uniform Finish
Coating
1 : 10% : 10%
1 : 20% : 10%
1 : 30% : 10%
4:1
Density (g/L)
998-1170
999-1158
998-1146
992
8.33-9.76
8.34-9.66
8.33-9.56
8.28
70-119
67-112
63-105
91
0.58-0.99
0.56-0.94
0.53-0.88
0.76
252-359
256-370
261-373
380
2.1-3.0
2.14-3.09
2.18-3.11
3.17
Volatiles wt. %
61.4-80.5
64.0-82.0
66.2-83.3
85.7
Water wt. %
51.2-70.0
54.3-72.1
57.0-74.0
76.6
Exempt wt. %
0.0
0.0
0.0
0.0
Water vol. %
60.0-72.1
63.0-74.1
65.5-75.8
76.1
0.0
0.0
0.0
0.0
Applicable Use Category
VOC Actual (g/L)
Exempt vol. %
RTS Combinations
Ratio
VOC Actual (g/L)
Exempt vol. %
7
EB-143 12/14
RTS Combinations
Color : T492
Color : T492 : T494/T595
Color : T492 : T494/T595
Color Coating
Color Coating
Color Coating
Ratio
100 : 10%
100 : 10% : +10%
100 : 10% : +20%
Density (g/L)
995-1056
996-1050
996-1045
8.30-8.81
8.31-8.76
8.31-8.72
55-102
52-95
48-87
0.46-0.84
0.43-0.79
0.40-0.73
216-403
219-405
223-407
1.80-3.36
1.83-3.38
1.86-3.40
Volatiles wt. %
75.9-86.3
77.9-87.5
79.9-88.7
Water wt. %
70.8-80.1
73.0-81.6
75.2-83.1
Exempt wt. %
0.0
0.0
0.0
Water vol. %
72.1-80.3
74.2-81.7
76.3-83.1
0.0
0.0
0.0
VOC Actual (g/L)
Exempt vol. %
Emergency Medical or Spill Control Information: (412) 434-4515; In Canada (514) 645-1320
Materials described are designed for application by professional, trained personnel using proper equipment and are not intended for sale to the general public.
Products mentioned may be hazardous and should only be used according to directions, while observing precautions and warning systems listed on label. Statements
and methods described are based upon the best information and practices known to PPG Industries. Procedures for applications mentioned are suggestions only and
are not to be construed as representations or warranties as to performance, result, or fitness for any intended use, nor does PPG Industries warrant freedom from patent
infringement in the use of any formula or process set forth herein.
PPG Automotive Refinish
19699 Progress Drive
Strongsville, OH 44149
800.647.6050
PPG Canada Inc.
2301 Royal Windsor Drive, Unit #6
Mississauga, Ontario L5J 1K5
888.310.4762
Follow us online:
www.ppgrefinish.com
The PPG Logo, Bringing innovation to the surface, Envirobase, OneChoice, Deltron, Global Refinish System, En.V, and H2O-So-Clean are trademarks
of PPG Industries Ohio, Inc.
Xirallic is a registered trademark of Merck Kgaa.
8
EB-143 12/14
P-178SP
Limpiadores solventes
Limpiadores DX
Los limpiadores DX de PPG han sido
diseñados específicamente para eliminar
cera, grasa, siliconas, brea de carreteras,
aceite para motor, exceso de pintura,
adhesivos y otros contaminantes. Los
limpiadores DX han sido empacados
listos para usar.
Limpiadores DX
• DX320 - Limpiador de evaporación rápida
• DX330 - Removedor de cera y grasa ACRYLI-CLEAN®
• DX394 - Limpiador con bajo COV 1.4
• DX440 - Removedor de cera y grasa DITZ-O®
Información del producto vigente a partir de 9/13
Limpiadores DX
Instrucciones de uso
Limpiador de evaporación
rápida DX320
• El limpiador de evaporación rápida DX320 debe utilizarse como lavado de limpieza final
antes de pintar.
• Limpie la superficie con DX330, DX 440 o DX394 como se describe a continuación antes de
lijar, encintar, imprimar y sellar.
• Puede utilizar DX320 para remover los contaminantes de la superficie, tal como las huellas
dactilares que quedan después de encintar.
• Puede ser utilizado en todos los acabados originales del fabricante, superficies de metal descubierto,
y sistemas de acabado curados y secos. No use DX320 sobre plástico o fibra de vidrio.
• Después del encintado final y antes de aplicar el sellador o la pintura, aplique DX320 de manera
abundante a la superficie que va a limpiar. Limpie inmediatamente con un paño limpio. No
permita que DX320 se seque sobre la superficie. Limpie un área no mayor a 2 pies por 2 pies
para evitar el secado prematuro.
DX330 Acryli-Clean
DX394 Limpiador con COV
bajo 1.4
DX440 Removedor de
cera y grasa Ditz-O
• Antes de limpiar, lave la superficie a tratar con agua y jabón.
• Limpie la superficie antes y después de lijar.
• Aplique una cantidad generosa de DX330, DX394 o DX440 con un paño blanco limpio o
aplíquelo con una botella rociadora de mano.
• La aplicación inicial hará que los contaminantes floten hacia la superficie, y al limpiar
una segunda vez con otro paño limpio y seco se eliminarán estos contaminantes.
• Para obtener resultados óptimos, seque con un paño blanco limpio pasándolo en una sola dirección
mientras la superficie todavía está mojada, para eliminar las manchas de contaminantes.
No use DX320, DX330 o DX440 sobre piezas de plástico o fibra de vidrio. La aplicación de estos
productos sobre estas superficies puede provocar la acumulación de estática y con ello una
combustión súbita.
No utilice DX440 sobre materiales solubles como imprimadores o revestimientos finales con laca.
Datos técnicos:
COV (lb/galón de EE.UU.)
Importante:
DX320
DX330
DX394
DX440
6.31
6.36
1.34
6.94
Precaución: Utilice protección ocular y de la piel, como guantes resistentes a solventes y gafas de seguridad mientras
utiliza productos para la limpieza de superficies. Use con ventilación adecuada. Obedezca todas las
precauciones que aparecen en la etiqueta y en la MSDS.
Nota:
Los reglamentos locales sobre la calidad del aire pueden limitar el uso de limpiadores DX específicos.
Verifique si son adecuados antes de utilizarlos.
Para obtener información adicional sobre seguridad e instrucciones de manipulación, vea las Hojas de Datos de
Seguridad del Material (MSDS) y las Etiquetas.
EN CASO DE EMERGENCIAS MÉDICAS O INFORMACIÓN DE CONTROL DE DERRAMES EN LOS EE.UU. LLAME AL
1 (412) 434-4515; EN CANADÁ 1 (514) 645-1320.
Los materiales descritos están diseñados para ser aplicados únicamente por personal profesionalmente capacitado, utilizando el equipo apropiado, y sin
la intención de ser vendidos al público en general. Los productos mencionados pueden ser peligrosos y deberán usarse únicamente de acuerdo a las
instrucciones, al tiempo que se observan todas las precauciones y advertencias enumeradas en la etiqueta. Las declaraciones y métodos descritos se basan
en las mejores prácticas e información conocida a la fecha por PPG Industries. Los procedimientos de aplicación mencionados son sugerencias únicamente
y no deben ser considerados como representaciones o garantías del desempeño, resultados o idoneidad de cualquier uso deseado, ni PPG Industries
garantiza que no se incurra en incumplimiento de patentes ante el uso de cualquier fórmula o proceso descrito en el presente documento.
Acabado de Automoción PPG
Introduciendo innovaciones en la superficie™
PPG Industries
1-800-647-6050
PPG Canada Inc.
1-888-310-4762
Deltron, Acryli-Clean, Ditz-O, el logotipo de PPG y Bringing innovation to the surface
son marcas comerciales registradas de PPG Industries of Ohio, Inc.
© 2013 PPG Industries www.ppgrefinish.com
Este documento
está impreso en
papel reciclado.
Parte No. P-178SP 9/13
P-246SP
DELTRON® Recubrimiento Transparente de Ultra Velocidad
DC2000
DC2000 es un recubrimiento transparente de
ultra velocidad y de primera calidad desarrollado
específicamente para aumentar la productividad en
instalaciones de reparación de colisiones con secado
al aire que también reduce los costos de energía en
instalaciones que cuentan con cabinas de horneado.
El Recubrimiento Transparente de Ultra Velocidad
Deltron está diseñado para usar en reparaciones
de 1 a 4 paneles. DC2000 ofrece tiempos de
secado, pulido y secado al aire extremadamente
rápido sin sacrificar la durabilidad ni el aspecto.
Características
● Secado rápido al aire
● Lije y pula en 30 minutos o menos
Ventajas
● Mayor producción
● Buen rendimiento en todo tipo de cabinas
● Agiliza el montaje y el tiempo posible de entrega
Beneficios
● Mayor productividad
● Reduce el tiempo de ciclo
Información del producto vigente a partir de 12/13
Superficies compatibles
Base ENVIROBASE® de Alto Rendimiento en Suspensión de Agua
Base Deltron 2000 (DBC)
Base GLOBAL REFINISH SYSTEM® BC
Pinturas de acabado y recubrimientos de acabado originales del fabricante
completamente curados y lijados
Productos requeridos
●
●
●
●
DC2000 Recubrimiento Transparente de Ultra Velocidad
DCH2015 Endurecedor
DR220 Reductor Acelerado de Temperatura Media (70°- 85 °F/21° - 29 ℃)
DT885 Disolvente de Temperatura Media (75 – 90 °F/24° - 32 °C)
DT895 Disolvente de Alta Temperatura (85 – 95 °F/29° - 35 ℃)
DT898 Disolvente de Temperatura muy Alta (95 °F y superior/35 °C y superior)
D871 Disolvente Medio (65° - 77 °F/18° - 25 °C)
D872 Disolvente Lento (77° - 95 °F/25° - 35 °C)
D873 Disolvente muy Lento (95 °F y superior/35 °C y superior)
DC2000
Instrucciones
Preparación:
Consulte en el Boletín de Producto específico la información sobre el sistema de colores, para su
aplicación, los tiempos de secado y las recomendaciones de mezcla.
Proporciones de mezcla:
DC2000
4 partes
:
:
DCH2015
1 parte
:
:
DR220/DT8xx/D8xx
.5 - 1 parte
Vida útil:
2 horas a 70 °F (21 ºC)
Aditivos:
DC2000
DX814
Flexibilizador
4 partes
DCH 2015
:
DC2000 :
DX73
Eliminador
de gos
Pescado
4 partes
:
1 parte
DCH 2015
1 parte
DR220/DT8xx/D8xx
:
.5 - 1 parte
DR220/DT8xx/D8xx
:
.5 - 1 parte
DX814
+
10%
:
DX73
+
1 oz. por
cuarto de
RTS
Para leer las recomendaciones para opacar colores, consulte el boletín OC-2 OneChoice®
Capas de aplicación:
Aplique:
2 capas medianas mojadas sin dejar secar entre una y
otra capa
Presión de aire:
HVLP:
De conformidad:
Convencional:
0.7 Kg/cm2 (10 psi) en el tapón
de aire
2.03 – 2.81 Kg/cm2 (29 - 40 psi)
en la pistola
3.16 – 3.86 Kg/cm2 (45 - 55 psi)
en la pistola
Nota: Para obtener los mejores resultados generales, consulte las recomendaciones del fabricante de la
pistola respecto a la presión de aire de entrada.
Ajuste de la pistola:
Boquilla:
Formación de película por capa húmeda:
Formación de película por capa seca:
Página 2 P-246SP
1.3 - 1.5 mm o equivalente
2 - 3 mils
1 - 1.5 mils
Instrucciones
Tiempos de secado:
Entre capas:
70 ºF/21 ºC
No es necesario secar por evaporación
Sin polvo:
70 ºF/21 ºC
9 a 12 minutos
Tiempo de cinta:
70 ºF/21 ºC
1 hora
Secado al aire hasta
re ensamblar:
70 ºF/21 ºC
1 hora
Secado forzado:
140 ºF/60 ºC
No se recomienda
IR (Infrarrojo)
No se recomienda
Pulido:
Secado al aire
70 ºF/21 ºC
25 a 30 minutos
2 a 3 horas de secado al aire a 70 ºF (21 ºC)
Para reparar o recubrir:
DC2000 se debe lijar antes de recubrir
con imprimador, color o recubrimiento
transparente.
Limpieza del equipo:
Las pistolas de rociado, los tapones de las pistolas, los envases de
almacenamiento, etc. se deben limpiar cuidadosamente después de cada
uso con cualquier solvente multiuso PPG apropiado.
Página 3 P-246SP
DC2000
Deltron Recubrimiento
Transparente de
Ultra Velocidad
Datos técnicos:
COV menos solventes exentos (aplicado a 4:1:1)
COV menos solventes exentos con DX814
(aplicado a 4:1:1+10%)
COV menos solventes exentos con DX73
(aplicado a 4:1:1+1 oz. por cuarto de RTS)
COV menos solventes exentos con SU4985 (aplicado a X:X:X:X)
Sólidos totales por volumen (aplicado a 4:1:1)
2
Rendimiento en pies /galón de EE.UU. (aplicado a 4:1:1)
Importante:
4.03 - 4.17 lb/gal (483 – 500 g/l)
4.37 - 4.44 lb/gal (524 – 532 g/l)
4.17 - 4.27 lb/gal (500 – 512 g/l)
5.04 - 5.26 lb/gal (604 – 630 g/l)
35.1%
564 a 1 mil, 100% de eficiencia
de transferencia
El contenido de este paquete debe ser mezclado con otros componentes antes de utilizarse. Antes
de abrir los paquetes, asegúrese de que entiende los mensajes de advertencia en las etiquetas de
todos los componentes, ya que la mezcla tendrá los riesgos de todas sus partes. La técnica de
rociado inadecuada puede provocar condiciones peligrosas. Siga las instrucciones del fabricante
del equipo de rociado para prevenir lesiones personales o incendios. Para usar un respirador, siga
las instrucciones. Use protectores de la piel y los ojos. Observe todas las precauciones aplicables.
Para obtener información adicional sobre seguridad e instrucciones de manipulación,
vea las Hojas de Datos de Seguridad del Material (MSDS) y las Etiquetas.
EN CASO DE EMERGENCIAS MÉDICAS O INFORMACIÓN DE CONTROL DE DERRAMES EN LOS EE.UU.
LLAME AL 1 (412) 434-4515; EN CANADÁ 1 (514) 645-1320.
Los materiales descritos están diseñados para ser aplicados únicamente por personal profesionalmente capacitado,
utilizando el equipo apropiado, y sin la intención de ser vendidos al público en general. Los productos mencionados pueden
ser peligrosos y deberán usarse únicamente de acuerdo a las instrucciones, al tiempo que se observan todas las precauciones
y advertencias enumeradas en la etiqueta. Las declaraciones y métodos descritos se basan en las mejores prácticas e
información conocida a la fecha por PPG Industries. Los procedimientos de aplicación mencionados son sugerencias
únicamente y no deben ser considerados como representaciones o garantías del desempeño, resultados o idoneidad de
cualquier uso deseado, ni PPG Industries garantiza que no se incurra en incumplimiento de patentes ante el uso de cualquier
fórmula o proceso descrito en el presente documento.
Acabado de Automoción PPG
Introduciendo innovaciones en la superficie™
PPG Industries
1-800-647-6050
PPG Canada Inc.
2301 Royal Windsor Drive Unit # 6
1-888-310-4762
www.ppgrefinish.com
Parte N.° P-246SP, 12/13
P-246
DELTRON® Ultra Velocity Clearcoat
DC2000
DC2000 is an ultra velocity, high quality
clearcoat, specifically developed to enhance
productivity in air-dry collision repair facilities
and also reduces energy cost in facilities with
baking booths.
Deltron Ultra Velocity Clearcoat is designed for
use on repairs of 1- 4 panels.
DC2000 offers extremely fast flash, polish and
air dry times without sacrificing durability or
appearance.
Features
● Fast air dry
● Sand and buff in 30 minutes or less
Advantages
● Faster throughput
● Performs well in all booth types
● Speeds up assembly and delivery time
Benefits
● Increased production
● Reduces cycle times
Product Information Effective 12/13
Compatible Surfaces
●
●
●
●
Deltron 2000 (DBC) Basecoat
GLOBAL REFINISH SYSTEMl® BC Basecoat
Fully cured and sanded OEM and refinish paints
Required Products
DC2000 Ultra Velocity Clearcoat
DCH2015 Hardener
DR220 Medium Temperature Accelerated Reducer (70°- 85°F / 21°- 29°C)
DT885 Mid Temperature Thinner (75 - 90°F / 24° - 32°C)
DT895 High Temperature Thinner (85 - 95°F / 29° - 35°C)
DT898 Very High Temperature Thinner (95°F and above / 35°C and above)
D871 Medium Thinner (65° - 77°F /18° - 25°C )
D872 Slow Thinner (77° - 95°F / 25° - 35°C )
D873 Very Slow Thinner (95°F and above / 35°C and above)
DC2000
Directions For Use
Preparation:
Refer to the specific product Information bulletin of the color system for its application, dry times,
and blend recommendations.
Mixing Ratios:
DC2000
4 parts
:
:
DCH2015
1 part
:
:
DR220/DT8xx/D8xx
½ to 1 part
Pot Life:
2 hours at 70ºF (21ºC)
Additives:
DC2000
DX814
Flexibilizer
DCH 2015
4 parts
:
1 part
DC2000
:
DCH 2015
4 parts
:
1 part
DX73
Fisheye
Eliminator
DR220/DT8xx/D8xx
+
10%
DR220/DT8xx/D8xx :
DX73
:
:
½ to 1 part
DX814
½ to 1 part
+
1 oz. to
RTS qt.
For flattening recommendations, see OneChoice® bulletin OC-2
Application Coats:
Apply:
2 medium wet coats with no flash between coats
Air Pressure:
HVLP:
Compliant:
Conventional:
10 psi at the air cap
29 - 40 psi at the gun
Note : For best overall results, refer to spraygun manufacturers recommendation for inlet air pressures.
Spray Gun Set-up:
Fluid Tip:
Film Build Per Wet Coat
Dried Film Build Per Coat:
Page 2 P-246
2 - 3 mils
1 - 1.5 mils
Directions For Use
Drying Times:
Between Coats:
70ºF / 21ºC
No flash required
Dust Free:
70ºF / 21ºC
9-12 minutes
Tape Time:
70ºF / 21ºC
1 hour
Air Dry to Re-assemble:
70ºF / 21ºC
1 hour
Force Dry:
140ºF / 60ºC
Not Recommended
IR
Not Recommended
Polishing:
Air Dry
70ºF / 21ºC
25- 30 minutes
Repair and Recoat:
2 - 3 hours air dry 70ºF (21ºC)
DC2000 must be sanded before recoating
with primer, color or clear.
Equipment Cleaning:
Spray guns, gun cups, storage pots, etc., should be cleaned thoroughly
after each use with any appropriate PPG general purpose solvent.
Page 3 P-246
DC2000
Deltron Ultra
Velocity Clearcoat
Technical Data:
Important:
VOC less exempt solvents (Applied 4:1:1)
4.03 - 4.17 lbs/gal (483 – 500 g/l)
VOC less exempt solvents w/DX814 (Applied 4:1:1+10%)
VOC less exempt solvents w/DX73 (Applied 4:1:1+1 oz. RTS qt.)
VOC less exempt solvents w/SU4985 (Applied X:X:X:X)
4.37 - 4.44 lbs/gal (524 – 532 g/l)
4.17 - 4.27 lbs/gal (500 – 512 g/l)
5.04 - 5.26 lbs/gal (604 – 630 g/l)
Total Solids by Volume (Applied 4:1:1)
35.1%
Sq. Ft Coverage / US Gal (Applied 4:1:1)
564 @ 1 mil, 100% transfer efficiency
The contents of this package must be blended with other components before the product can be
used. Before opening the packages, be sure you understand the warning messages on the labels of
all components, since the mixture will have the hazards of all its parts. Improper spray technique
may result in a hazardous condition. Follow spray equipment manufacturer’s instructions to
prevent personal injury or fire. Follow directions for respirator use. Wear eye and skin
protection. Observe all applicable precautions.
EMERGENCY MEDICAL OR SPILL CONTROL INFORMATION (412) 434-4515; IN CANADA (514) 645-1320
Materials described are designed for application by professional, trained personnel using proper equipment and are not
intended for sale to the public. Products mentioned may be hazardous and should only be used according to directions,
while observing precautions and warning statements listed on label. Statements and methods described are based upon the
best information and practices known to PPG Industries. Procedures for applications mentioned are suggestions only and
are not to be construed as representations or warranties as to performance, results, or fitness for any intended use, nor does
PPG Industries warrant freedom from patent infringement in the use of any formula or process set forth herein.
PPG Industries
1-800-647-6050
PPG Canada Inc.
2301 Royal Windsor Drive Unit #6
1-888-310-4762
The PPG logo, Deltron, Envirobase, Global Refinish System, OneChoice and Bringing innovation to the surface are registered trademarks of
PPG Industries Ohio, Inc.
www.ppgrefinish.com
Part No. P-246, 12/13
North America
Technical Data Sheet S2.02.08
Primer/Surfacer
05.13.2010
Autosurfacer Rapid
FOR PROFESSIONAL USE ONLY
Description
Autosurfacer Rapid is a high build, two-component, isocyanate free product that is used as a sanding primer surfacer. Provides
fast air drying and baking qualities. Usable under all Sikkens primer sealers and top coats. Autosurfacer Rapid provides
excellent application and sanding properties and very good enamel-hold out in combination with all Sikkens topcoats.
100
50
Autosurfacer Rapid
Autosurfacer Rapid Hardener
Use Sikkens Measuring Stick #1 (Black)
Spray gun set-up:
Gravity 1.6 –1.8 mm
HVLP 1.7–2.0 mm
Application pressure:
28 – 30 psi at the air inlet
o Check gun manufacturer specification
2-3 x 1 coat
Between coats
3–5 minutes at 70°F (20°C)
Before curing
1–3 minutes at 70°F (20°C)
70°F (20°C)
45 minutes
140°F (60°C)
20 minutes
Final sanding step; #P500 - #P600 Sikkens topcoats
Final sanding step; #P400 when applying Sikkens sealers
Recoatable with all Sikkens topcoats
Use suitable respiratory protection
Akzo Nobel Car Refinishes recommends to use fresh air supply respirator.
Read complete TDS for detailed product information
1/5
North America
Primer/Surfacer
05.13.2010
Autosurfacer Rapid
Description
Autosurfacer Rapid is a high build, two-component, isocyanate free product that is used as a sanding primer surfacer. Provides
fast air drying and baking qualities. Usable under all Sikkens primer sealers and top coats. Autosurfacer Rapid provides
excellent application and sanding properties and very good enamel-hold out in combination with all Sikkens topcoats.
Product and additives
Products:
-Autosurfacer Rapid Dark Grey
-Autosurfacer Rapid Light Grey
Hardener:
Autosurfacer Rapid Hardener
Additive:
Autosurfacer Flex: A special additive to improve flexibility when spraying
plastic parts.
o In the event of application over raw untreated plastic parts It is
advisable to use Primer PO or Plastoflex Primer on any exposed
untreated plastic before applying Autosurfacer Rapid.
Basic raw materials
-Autosurfacer Rapid:
-Autosurfacer Rapid Hardener:
special acrylic resins
blocked polyamines of high molecular weight
Suitable substrates
-Existing finishes, degreased and sanded with #P220 to #P320 grit paper dry.
-OEM electrocoats (Ecoat), degreased and sanded with #P220 to #P320 grit paper dry or
thorough scuff with Scotch-Brite maroon #7447.
-Any premium polyester bodyfiller, final sanded with #P180 to #P220 grit dry.
-Steel, degreased and sanded with #P80 then #P120 grit dry.
-Galvanized, degreased and sanded with #P150 to #P180 grit dry.
-Fiberglass gelcoat, degreased and sanded with #P220 to #P320 grit dry. If the gelcoat is broken
and has been sanded through, under no circumstance should Autosurfacer Rapid be applied.
Recommended is the use of Polysurfacer.
o
Although Autosurfacer Rapid will provide adequate adhesion on bare metal, repairs
which require extensive metal priming such as whole panel and panels that have had
the existing paint system removed, Autosurfacer Rapid should be applied over
Washprimer 1K CF or Washprimer EM CF. Allow a 15 minutes flash-off at 70°F (20°C)
after Washprimer 1K CF and a 30 minutes flash-off at 70°F (20°C) after Washprimer EM
CF application.
Mixing
Autosurfacer Rapid, Light Grey and Dark Grey can be intermixed before proceeding with adding
hardener. To make a medium shade of grey; To 100 parts by volume of Light Grey, add 20 parts
by volume of Dark Grey. This mixture must further be prepared as follows
Mixing ratio
Mixing Ratio by Volume:
100 parts of Autosurfacer Rapid
50 parts of Autosurfacer Rapid Hardener
For easy and accurate mixing, use the Sikkens Measuring Stick #9 (grey).
2/5
North America
Primer/Surfacer
05.13.2010
Autosurfacer Rapid
Viscosity
20–22 seconds – DIN Cup #4 at 70°F (20°C)
Spray gun set-up / application pressure
Spray gun
Gravity
HVLP Gravity
feed
High Transfer
Gravity
Fluid tip – set-up
Application pressure
1.6-1.8 mm
1.7-2.0 mm
1.6-1.8 mm
40–45 psi at the spray gun air inlet
HVLP max 10 psi at the air cap.
35 psi at the spray gun air inlet.
o
Check gun manufacturer specification
Application process
Spray application;
Apply one single coat over any sand through areas. allow this to flash until surface is completely
matt.
Apply two to three single wet coats; allow a flash off time of 3–5 minutes between coats.
Dependant on the required film build.
o Today, many spray gun manufacturers have introduced the small size gravity gun.
These spray guns provide the benefit of keeping the overspray contamination to a
minimum. For small local repairs consider reducing the gun inlet air pressure to +- 25psi
and use a 1.3 to 1.4mm fluid tip.
Rolling application;
With a small dense foam roller. Apply one light coat over any sand through areas. Next apply the
second and third coat within each preceding coat. Use the edge of the roller to prime awkward
areas. Finally, squeeze remaining paint from roller on the pan shelf and smooth off the repair.
The rolling should be from the outside in.
o Rolling application will never provide the same film build as spray application. To
achieve the best possible film build, allow each coat to flash off well until the surface is
completely matt.
Flexible plastic parts
Prior to mixing with Hardener. Add 50 parts by volume of Autosurfacer Flex to Autosurfacer
Rapid. Use the first two columns on the #1 (Black) measuring stick; stir this mixture thoroughly
before further preparation.
Pot-life
30 minutes at 70°F (20°C)
As temperature increases 18°F (10°C) the pot-life decreases 50%
Film thickness
For recommended spray application (3 coats): 6.5-7.5 mils (150-180 µm)
3/5
North America
Primer/Surfacer
05.13.2010
Autosurfacer Rapid
Drying times
Drying times relate to recommended application and object temperature
Ready to sand Distance between short wave IR unit and object. 20 –27 inch (50-70 cm)
The panel must not exceed temperatures above 212°F (100°C)
70°F (20°C)
45 minutes
140°F (60°C)
20 minutes
6 minutes
Allow 5 minute flash off
prior to infra red curing.
Sanding
Wet: May be presanded with #P600 grit paper wet, final sand with #P800 to #P1000 grit wet.
If sanded wet allow 30 minutes at 70°F (20°C) drying time before application of a sealer or top
coat
Dry: May be presanded with #P320 to #P360 grit dry, moving in stages to final sanding
with #P400 to #P500 grit dry.
Sanding in the case of roller application;
Pre sand with a sanding block, with a coarser sanding grit; Dry, #P320, in order to remove the
coarser surface structure due to the roller application. Sanding should be done from the inside
out.
o Normally a wet-on-wet primer sealer is required after sanding, before the top coat is
applied.
Recoatable with
After sanding and surface cleaning. Autosurfacer Rapid may be coated itself or with any Sikkens
primer sealer or top coat.
o
In the case of repriming with itself. Potentially the system laid down is a layer of
Washprimer after which two to three coats of Autosurfacer Rapid have been applied and
after aggressive sanding, noticed are areas of Washprimer being exposed.
In this case it is advisable to apply heat, such as Infra Red drying for a minimum of 6 minutes.
Please see I.R. drying schedule under drying times information, previous page. Before
continuing further repriming with Autosurfacer Rapid, or allow overnight drying.
Failure to consider this could provide slight wrinkling of the original thin feather edge of
Autosurfacer Rapid.
Material usage
With recommended spray application (3 coats), the theoretical material usage is approximately;
18 sq.ft./liter (1.7 m²/liter) ready to spray mixture.
The practical material usage depends on many factors i.e. shape of the object, roughness of the
surface, application techniques, pressure, method and application circumstances.
Cleaning of equipment
Clean spray equipment with Sikkens Cleaning Solvents or lacquer thinner.
Packaging
–Autosurfacer Rapid:
–Autosurfacer Rapid Hardener:
4/5
3 Liter can
1 Liter can
North America
Primer/Surfacer
05.13.2010
Autosurfacer Rapid
Color
Light Grey and Dark Grey
VOC
Autosurfacer Rapid (100:50)
4.8 lb/gal (580 g/l) ready to spray mixture.
Safety aspects
Store products unopened between 70°F and 95°F (10°C and 35°C)
Avoid too much temperature fluctuation, optimal storage temperature ± 70°C (20°C).
Shelf Life:
–Autosurfacer Rapid:
2 years if stored unopened
–Autosurfacer Rapid Hardener: 1.5 years if stored unopened
Akzo Nobel Car Refinishes Inc. North America
Address: 5555 Spalding Drive, Norcross. GA 30092 USA
Tel:
770-662-8464
IMPORTANT NOTE The information in this data sheet is not intended to be exhaustive and is based on the present state of our knowledge and on current laws:
any person using the product for any purpose other than that specifically recommended in the technical data sheet without first obtaining written confirmation from
us as to the suitability of the product for the intended purpose does so at his own risk. It is always the responsibility of the user to take all necessary steps to fulfill
the demands set out in the local rules and legislation. Always read the Material Data Sheet and the Technical Data Sheet for this product if available. All advice we
give or any statement made about the product by us (whether in this data sheet or otherwise) is correct to the best of our knowledge but we have no control over
the quality or the condition of the substrate or the many factors affecting the use and application of the product. Therefore, unless we specifically agree in writing
otherwise, we do not accept any liability whatsoever for the performance of the product or for any loss or damage arising out of the use of the product. All products
supplied and technical advices given are subject to our standard terms and conditions of sale. You should request a copy of this document and review it carefully.
The information contained in this data sheet is subject to modification from time to time in the light of experience and our policy of continuous development. It is the
user's responsibility to verify that this data sheet is current prior to using the product.
Coatings brand names mentioned in this data sheet are trademarks of or are licensed to AkzoNobel.
Head Office
Akzo Nobel Car Refinishes B.V., PO Box 3 2170 BA Sassenheim, The Netherlands. www.sikkenscr.com
5/5
Technical Data Sheet
Cleaners
December 2014
AutoPrep Ultra Prep Surface Cleaner
Description
UltraPrep Surface Cleaner is a waterbased surface cleaner with low VOC content. UltraPrep Surface Cleaner is
used to ensure removal of all kinds of contamination from the substrate prior to paint application.
Suitable Substrates
Steel
Stainless Steel
Zinc Coated Steel
Aluminum
Existing Finishes
Plastic Substrate
Cleaning technique
After washing the car or the surface of the body panel under treatment, wet a clean cloth with the
UltraPrep Surface Cleaner and clean the surface under treatment. Immediately thereafter, wipe the
surface thoroughly dry with high quality absorbent surface cleaning cloths.
Always use two cloths, as one cloth will merely shift rather than remove dirt and grease.
Do not allow the surface cleaner to evaporate on substrate or the contamination on the surface will
remain.
Wipe the substrate thoroughly dry before the surface cleaner evaporates.
The purpose of surface cleaning is to remove residual grease, oil, wax, silicones, sand, etc. If this
is not done, residual contaminant will remain in scratch marks during sanding. Adhesion of the
paint system subsequently applied to the contaminated surface will be poor and could delaminate.
o Replace cloths being used for cleaning regularly by clean ones. Instead of placing used
(wet) rags in a sealed container place them on the floor grating so that the solvents can
evaporate, then place the dried cloths in the regular dustbin.
Point of attention on surface cleaning:
Salt residue and blistering:
With all cleaning activities: once the surface under treatment has been cleaned, it must never be
touched with the bare hand; as salts, moisture and oils can be transferred to the prepared surface
which may result in delamination or blistering problems. It is particularly important that hand
protecting barrier creams are never used near an automobile that is to be refinished.
Should you still have touched a sanded and cleaned surface with bare hands; clean it again with
first one of the solvent borne and next with one of the water borne cleaners again according the
recommended cleaning technique.
Truck body constructions:
It is important to prevent dirt residues from getting into construction joints of vans, lorries, etc.
during cleaning . They might cause adhesion problems when the paint is applied. Vertically fitted
parts should, therefore, first be the surface should be cleaned from the bottom upwards and
subsequently from the top downwards.
1/2
Cleaners
December 2014
Point of attention on surface cleaning continued):
Cleaning and condensation on metal surfaces:
After a surface has been cleaned, solvent will evaporate. Heat needed for
evaporation is withdrawn from that surface, making it colder than the surrounding atmosphere, which results
in (often not visible) condensation on the surface. Allow the moisture sufficient time to evaporate.
The first coat of paint can be applied as soon as the surface has re-gained the temperature of the
surrounding atmosphere. Earlier application of the coat may lead to adhesion problems.
The same problem may arise if a vehicle is transferred from a cold room to a warm one or from outdoors to
indoors. Allow vehicles a minimum of one hour to acclimatize. Double-walled vehicles (and certainly
insulated ones) require some hours to acclimatize.
Health and Safety
Akzo Nobel Car Refinishes recommends providing adequate ventilation during surface cleaning with any of
the mentioned cleaners. Where reasonably practicable, this should be achieved by the use of local exhaust
ventilation and good general extraction. If these are not sufficient to maintain concentrations of particulates
and solvent vapours below the OEL, suitable respiratory protection must be worn.
Besides respiratory protection, always wear solvent resistant gloves while surface cleaning even though
working with a low solvent degreaser. This will reduce the risk of cleaning solvents being absorbed into the
skin and prevent salts and oils on your hands from contaminating the surface to be refinished.
VOC
The VOC content of this product in ready to use form is 0.00 g/liter.
Product storage
Product shelf life is determined when products are stored unopened at 70°F (20°C).
Avoid too much temperature fluctuation.
o Product shelf life is 1 year
AkzoNobel Automotive and Aerospace Coatings, Inc
Address: 3587 Parkway Lane, Norcross, GA 30092
Tel: 770-662-8464
IMPORTANT NOTE The information in this data sheet is not intended to be exhaustive and is based on the present state of our knowledge and on current
laws: any person using the product for any purpose other than that specifically recommended in the technical data sheet without first obtaining written
confirmation from us as to the suitability of the product for the intended purpose does so at his own risk. It is always the responsibility of the user to take all
necessary steps to fulfill the demands set out in the local rules and legislation. Always read the Material Data Sheet and the Technical Data Sheet for this
product if available. All advice we give or any statement made about the product by us (whether in this data sheet or otherwise) is correct to the best of our
knowledge but we have no control over the quality or the condition of the substrate or the many factors affecting the use and application of the product.
Therefore, unless we specifically agree in writing otherwise, we do not accept any liability whatsoever for the performance of the product or for any loss or
damage arising out of the use of the product. All products supplied and technical advices given are subject to our standard terms and conditions of sale. You
should request a copy of this document and review it carefully. The information contained in this data sheet is subject to modification from time to time in the
light of experience and our policy of continuous development. It is the user's responsibility to verify that this data sheet is current prior to using the product.
Brand names mentioned in this data sheet are trademarks of or are licensed to Akzo Nobel.
Head Office
2/2
Product Information
Product Description
Envirobase High Performance is a premium waterborne color system for use in repair and repainting of motor
vehicles. Industry leading color capability is easily achieved when applied as part of a two or three-stage basecoat/
clearcoat paint process. Mixed Envirobase High Performance color reproduces the original OEM solid, metallic,
mica, or XIRALLIC® paint finish of virtually all OEM manufacture's worldwide.
Envirobase High Performance products are engineered to reduce volatile organic compounds (VOC) and will
exceed all of today’s legislative VOC restrictions throughout the United States and Canada.
Envirobase High Performance waterborne color system is also capable of producing internal color as well as
interior color. For additional information, see Envirobase product bulletins EB145 for interior color and EB510 for
internal color.
Preparation of Substrate
Apply over original baked finishes or over recommended undercoats.
In all cases, wash all surfaces to be painted with soap and water. Final clean with an appropriate
waterborne cleaner. Ensure that the substrate is thoroughly cleaned and dried before starting
repair.
Apply Envirobase High Performance after sanding with European P800-P1200 / US 500-600
grade paper or dry sand with European P600-800 / US 500-600 grade paper.
Wash off residue and dry thoroughly before recleaning with appropriate waterborne substrate
cleaner. The use of a tack rag is recommended.
•
Before mixing, gently hand shake bottles of the Envirobase High Performance toners for a few seconds before
use. Do not place toners or mixed color on shaker or mechanically agitate.
•
Mixed Envirobase High Performance color should be thoroughly hand-stirred before application. If not used
immediately it should be hand-stirred again before use.
•
Use nylon 125 micron paint filters specially designed for use with waterborne paint materials.
EB-143 12/14
APPLICATION GUIDE:
Mixing Ratio:
T494/T595**
1 Part
OR
T492 Adjuster*
1 Part
Envirobase High Performance Metallic / Pearl Color
T492 Adjuster*
T494/T595** Thinner
1 Part
+10% by volume for metallic / pearl color
Envirobase High Performance Tinted Mid Coat Color
T492 Adjuster*
T494/T595** Thinner
1 Part
+20% by volume for tinted mid-coat color
*T492 Adjuster has been specifically developed as an enhancement to the Envirobase High Performance basecoat system. Leading edge
parts such as bumpers and fascia’s or low profile front ends that may be prone to stone chipping or when driving in extreme conditions
such as abrasive gravel roads or when subjected to high powered pressure washing, the addition of T492 adjuster will improve the
basecoat film properties. Note: Application, flash off and drying is the same as with the standard process. If additional reduction is
required for viscosity adjustment, DO NOT add additional T492, use T494/T595 only.
** T595 is for use in high heat, low humidity conditions only. See thinner selection guide on page 6 for additional information.
Pot Life
Un-activated, 90 days stored in sealed plastic containers. If activated, pot life is 2 hours.
Hand stir well before using. Do Not mechanically shake.
Additives
T581 (optional activator) - 10% by volume after reducing. After activation, additional thinner may be
required to bring the color into the 23-28 second sprayable viscosity range.
Spraygun set up
Fluid Tip:
Spray Viscosity:
23 - 28 seconds, DIN4 @70°F (21°C)
HVLP at the air cap
Conventional at the spray gun
Color Coat
*
*
Spray Pressure
Control Coat
*
*
*Spray gun pressure will vary by manufacturer. See spray gun setup chart DOX440 on ppgrefinish.com
Envirobase / Technical Data Sheets & MSDS Index tab for manufacturer’s pressure information.
Number of Coats
All repairs:
2-3 coats to coverage plus control coat*
Horizontal surfaces may require two control coats where vertical surfaces will generaly only require one
control coat.
*Note: A control coat is not required for solid colors.
Flash Off
70°F (21°C)
Between Coats:
1-2 minutes or until dried to a matt finish
Final Flash-off:
When application is complete, apply the control coat and allow
it to dry naturally. Force drying of the control coat is not
necessary.
Note: Do not use the spray gun as an air drier. Use air drying equipment.
2
EB-143 12/14
APPLICATION GUIDE (cont’d):
Drying Times
Dust-Free
70°F (21°C)
Each coat approximately 2-4 minutes
Dry to Handle
70°F (21°C)
Dry to De-Nib:
70°F (21°C)
Tape Time
70°F (21°C)
5 minutes
Dry to Clear
70°F (21°C)
15 minutes minimum
Note: Because of the intensity of IR curing, if the clearcoat is to be cured using IR the basecoat will first
need to be cured with IR to remove the residual moisture from the basecoat film.
Overcoat/Recoat
Overcoat with any compatible clear
Flash off until the entire surface is touch-dry and has a uniform
matt appearance, or for 15 minutes.*
Dry Sand
Use European P1500 / US 800 grit
Recoat
After 24 hours, 1 coat of Envirobase High Performance must be
applied prior to the clearcoat application. The maximum recoat
time is 48 hours.
*Temperature, humidity, air movement and film build affect dry times. The best results are achieved with
increased temperature and air movement with minimal film builds.
BLENDING / WET BED
Mixing Ratio:
T490 Tinted Clear Additive
T494 / T595* Thinner
4 Parts
1 Part
For use as a blending additive: Add up to 1 equal par t of the T490 mixtur e to 1 par t of r eady to spr ay
color and fade into the prepared blend panel.
or
For use as a wet bed: Apply 1 medium light coat of the T490 mixtur e to the blend panel and or the
entire repair panel and allow to dry. It will be milky blue when wet but will dry translucent. Once dry, apply
color. Be sure that whatever the wet bed material has been applied, it is completely covered with earlier
basecoat or clearcoat.
*T595 is for use in high heat, low humidity conditions only. See thinner selection guide on page 6 for additional information.
3 STAGE PEARL PROCESS
Mixing Ratio:
Ground Coat
Color
Pearl Coat
1 part
10%**
Color
1 part
20%**
**Note: Percentage by volume. If using T492 Adjuster, see page 2 for proper use.
* T595 is for use in high heat, low humidity conditions only. See thinner selection guide on page 6 for
additional information.
3
EB-143 12/14
3 STAGE PEARL PROCESS (cont’d):
Viscosity:
Viscosity &
Pot Life:
Pot Life:
90 days stored in sealed plastic containers.
Always strain before use (nylon 125 micron is recommended).
Spray Gun &
Air Pressure
Fluid Tip:
1.2 - 1.4 mm
HVLP
Compliant
Color Coat
*
*
Control Coat
*
*
Application:
Ground Coat
•
•
•
•
•
Pearl Coat
Avoid heavy application and excessive film
builds.
Use air movement equipment to accelerate
drying as necessary. Choice of drying methods
will depend upon the type and size or the repair.
A control coat is not required for solid color
basecoats.
•
•
•
•
Horizontal and vertical surfaces
panels. Flash off thoroughly between coats.
Apply the control coat and allow it to dry
naturally.
Force drying of the control coat is not necessary.
The pearl color layer is not designed to give
opacity.
Flash Off:
Flash off until uniformly matt in appearance.
Dry Time:
Wait until ground coat is uniformly dry before
applying pearl coat
3 STAGE TINTED MID COAT PROCESS
Mixing Ratio:
Ground Coat
Color
Wait until pearl coat is uniformly dry before applying
clearcoat, approximately 15 minutes.
Tinted Mid Coat
1 part
20% **
Color
T492/T494/T595 Thinner
1 part
30%**
** Note: Percentage by volume. If using T492 Adjuster, see page 2 for proper use.
* T595 is for use in high heat, low humidity conditions only. See thinner selection guide on page 6 for additional information.
Viscosity &
Pot Life
Viscosity:
Pot Life:
90 days stored in sealed plastic containers
Always strain before use (nylon 125 micron is recommended)
Spray Gun &
Air Pressure
Fluid Tip:
1.2 - 1.4 mm*
HVLP
Compliant
Color Coat
*
*
Control Coat
*
*
4
EB-143 12/14
3 STAGE TINTED MID COAT PROCESS (cont’d):
Application:
Ground Coat
•
•
•
Tinted Mid Coat
Apply the control coat onto dry film for even
metallic appearance.
•
•
•
•
•
panels.
The mid coat layer is not designed to give
opacity.
Flash off the mid coat until it is uniformly dry
before applying clearcoat, approximately 15
minutes.
A control coat is not required for the tinted
midcoat layer.
Minor Repair Guidelines
Dirt nibs or other defects in the Envirobase High Performance paint film may be repaired as follows:
1.
2.
3.
4.
5.
Allow the surface to completely flash-off.
Dry sand the defect with P1500/US 800 grade paper or finer or with a fine abrasive pad or in combination with a small amount of SXA330 Wax and Grease
Remover as a sanding lubricant.
Remove sanding dust from the surface by strong air blowing with a clean air supply
Tack off surface with SX1070 tack rag.
Re-coat the surface with Envirobase High Performance as normal.
Compatibility
Low VOC Markets
National Rule Markets
EC530 En.V™ Performance Clearcoat
ECS6x A-Chromatic Sealer
EC530 En.V Performance Clearcoat
ONECHOICE®
SX1071 Etch Prime**
Plastic Prep System*** (SU4901, SUA4903)
OneChoice
SX1057 Flexible 2K Surfacer
SX1060 Rollable 2K Primer Surfacer
Plastic Prep System*** (SU4901, SU4902, SU4903, SUA4903)
SWX350 H2O-So-Clean
D8188
D8126
D820***
D800x*
D8099**
D8101
D8102
D8115
D8117
D8150
DELTRON®
DPLV305x
DPLV Epoxy
NCP280*
DCU2010
DC3010
DC4010
DC4125
Deltron
DPS305x*
DVLP Epoxy
K36
DCU2021
DCU2042
DCU2060
DCU2082
DC2000
DC3000
DC4000
DC4125
DX179x***
DPX801***
DPLF*
D8126
D8152
D893
D894
* For optimum performance a 2K primer or sealer may be used.
** For optimum performance a 2K sealer may be used.
*** Must be primed or sealed.
5
EB-143 12/14
Envirobase High Performance Waterborne Thinner Selection Guide
Note: Using T595 water bor ne thinner with humidity levels above 30% can cause extr emely slow flash and overall drying of the basecoat.
Do not blend waterborne thinners as this will affect overall basecoat performance. Use either T494 or T595 depending on humidity.
Health and Safety
•
•
•
•
•
•
•
•
The contents of this package may have to be blended with other components before the product can be used. Before opening the
packages, be sure you understand the warning messages on the labels and MSDS of all the components, since the mixture will have
the hazards of all its parts.
Improper handling and use, for example, poor spray technique, inadequate engineering controls and/or lack of proper Personal
Protective Equipment (PPE), may result in hazardous conditions or injury.
Follow spray equipment manufacturer’s instructions to prevent personal injury or fire.
Provide adequate ventilation for health and fire hazard control.
Follow company policy, product MSDS and respirator manufacturer’s recommendations for selection and proper sue of respiratory
protection. Be sure employees are adequately trained on the safe use of respirators per company and regulatory requirements.
Wear appropriate PPE such as eye and skin protection. In the event of injury, see first aid procedures on MSDS.
Always observe all applicable precautions and follow good safety and hygiene practices.
Equipment
Clean all mixing equipment immediately after use, preferably using a dedicated waterborne equipment cleaning machine with a final
rinse using waterborne thinner. Ensure all equipment is completely dry before storage or use.
Cleaning
Storage & Handling of Envirobase High Performance
• Envirobase High Performance tinters, Envirobase High Performance mixed color & waterborne thinner should be stored in a cool,
•
•
•
•
dry place away from sources of heat. During storage and transportation, temperature must be maintained at a minimum of 41°F or
+5°C or and a maximum of 120°F or 49°C. Avoid exposure to frost or freezing conditions.
Envirobase High Performance should be mixed in clean, dry plastic containers and equipment. Do not use mixing vessels or spray
equipment that contains solvent residues. Mixing vessels should ideally be plastic - if metal the container should be stainless steel or
have an internal anticorrosion coating.
Store waterborne & solvent borne wastes separately. A competent agent with appropriate certification must handle all waterborne
wastes. Waste must be disposed of in accordance with all Federal, State, Provincial and local laws and regulations.
Blended to spray basecoat color with T581 activator has a flash point above 200°F and may be disposed in the waterborne waste
stream intended for basecoat color (without activator). The waste disposal facility should be informed that the waste stream contains
isocyanates. T581 activator handled alone should be disposed in the solvent borne waste stream.
The Envirobase High performance waterborne paint residues should be segregated from all other wastes and kept in a separate
closed lined container. The Envirobase High Performance waterborne paint residues must be disposed or in accordance with all
Federal, State, Provincial and local laws and regulations.
6
EB-143 12/14
TECHNICAL DATA
Theoretical coverage (RTS), giving 12.7µm (0.5 mils) dry film thickness, 274-640 sq. ft. per US gallon.
Percent solids by volume RTS
8.5 - 20.0%
RTS Combinations
Color
Color : T494/T595
Color : T494/T595
Color : T494/T595
Color Coating
Color Coating
Color Coating
Color Coating
Ratio
Packaged
1 : 10%
1 : 20%
1 : 30%
Density (g/L)
991-1204
992-1186
992-1171
992-1156
8.27-10.05
8.28-9.90
8.28-9.77
8.28-9.65
47-120
44-111
43-103
41-97
0.39-1.00
0.37-0.93
0.36-0.86
0.34-0.81
207-395
213-401
219-407
225-419
1.73-3.30
1.78-3.35
1.83-3.40
1.88-3.50
Volatiles wt. %
60.42-84.97
63.42-86.29
66.01-87.44
68.26-88.40
Water wt. %
51.37-74.99
54.94-77.09
58.00-78.85
60.05-80.33
Exempt wt. %
0.0
0.0
0.0
0.0
Water vol. %
61.98-77.47
65.29-79.41
68.03-80.96
70.26-82.22
0.0
0.0
0.0
0.0
Color : T494/T595 :
T581
Color : T494/T595 :
T581
Color : T494/T595 :
T581
T490 : T494/T595
Color Coating
Color Coating
Color Coating
Uniform Finish
Coating
1 : 10% : 10%
1 : 20% : 10%
1 : 30% : 10%
4:1
Density (g/L)
998-1170
999-1158
998-1146
992
8.33-9.76
8.34-9.66
8.33-9.56
8.28
70-119
67-112
63-105
91
0.58-0.99
0.56-0.94
0.53-0.88
0.76
252-359
256-370
261-373
380
2.1-3.0
2.14-3.09
2.18-3.11
3.17
Volatiles wt. %
61.4-80.5
64.0-82.0
66.2-83.3
85.7
Water wt. %
51.2-70.0
54.3-72.1
57.0-74.0
76.6
Exempt wt. %
0.0
0.0
0.0
0.0
Water vol. %
60.0-72.1
63.0-74.1
65.5-75.8
76.1
0.0
0.0
0.0
0.0
VOC Actual (g/L)
Exempt vol. %
RTS Combinations
Ratio
VOC Actual (g/L)
Exempt vol. %
7
EB-143 12/14
RTS Combinations
Color : T492
Color : T492 : T494/T595
Color : T492 : T494/T595
Color Coating
Color Coating
Color Coating
Ratio
100 : 10%
100 : 10% : +10%
100 : 10% : +20%
Density (g/L)
995-1056
996-1050
996-1045
8.30-8.81
8.31-8.76
8.31-8.72
55-102
52-95
48-87
0.46-0.84
0.43-0.79
0.40-0.73
216-403
219-405
223-407
1.80-3.36
1.83-3.38
1.86-3.40
Volatiles wt. %
75.9-86.3
77.9-87.5
79.9-88.7
Water wt. %
70.8-80.1
73.0-81.6
75.2-83.1
Exempt wt. %
0.0
0.0
0.0
Water vol. %
72.1-80.3
74.2-81.7
76.3-83.1
0.0
0.0
0.0
VOC Actual (g/L)
Exempt vol. %
Emergency Medical or Spill Control Information: (412) 434-4515; In Canada (514) 645-1320
Materials described are designed for application by professional, trained personnel using proper equipment and are not intended for sale to the general public.
Products mentioned may be hazardous and should only be used according to directions, while observing precautions and warning systems listed on label. Statements
and methods described are based upon the best information and practices known to PPG Industries. Procedures for applications mentioned are suggestions only and
are not to be construed as representations or warranties as to performance, result, or fitness for any intended use, nor does PPG Industries warrant freedom from patent
infringement in the use of any formula or process set forth herein.
800.647.6050
PPG Canada Inc.
888.310.4762
Follow us online:
www.ppgrefinish.com
The PPG Logo, Bringing innovation to the surface, Envirobase, OneChoice, Deltron, Global Refinish System, En.V, and H2O-So-Clean are trademarks
of PPG Industries Ohio, Inc.
Xirallic is a registered trademark of Merck Kgaa.
8
EB-143 12/14
Información del producto
Capa base ENVIROBASE® de Alto Rendimiento, soluble en agua
Descripción del producto
La capa base Envirobase de Alto Rendimiento es un sistema de colores soluble en agua y de alta calidad para
utilizarse en la reparación y el repintado de vehículos motorizados. Se pueden lograr fácilmente propiedades de
color líderes en la industria cuando se aplica como parte de un proceso de pintura de capa base/revestimiento
transparente de dos o tres etapas. El color combinado de Envirobase de Alto Rendimiento reproduce el acabado de
pintura original del fabricante de color sólido, metálico, mica o XIRALLIC® de prácticamente todos los fabricantes
de equipos originales en el mundo.
Los productos Envirobase de Alto Rendimiento están diseñados para reducir los compuestos orgánicos volátiles (COV),
y excederán todas las restricciones legislativas actuales sobre COV en todo el territorio de Estados Unidos y Canadá.
El sistema de color, soluble en agua, de Envirobase de Alto Rendimiento también tiene la capacidad de producir
color interno como color interior. Para obtener más información, consulte los boletines de productos de Envirobase
EB145 para color interior y EB510 para color interno.
Preparación del sustrato
Aplique sobre acabados originales horneados o sobre capas base recomendadas.
En todos los casos, lave con agua y jabón todas las superficies que deben pintarse. La limpieza
final debe realizarse con un limpiador en suspensión de agua adecuado. Verifique que el sustrato
esté totalmente limpio y seco antes de empezar la reparación.
Aplique Envirobase de Alto Rendimiento después de lijar con papel lija grado P800 a P1200
europeo o grado 500 a 600 de EE. UU., o lije en seco con papel lija grado P600 a P800 europeo
o 500 a 600 de de EE. UU.
Lave para eliminar todos los residuos y deje secar completamente antes de volver a limpiar con
el limpiador en suspensión de agua adecuado. Se recomienda usar un trapo humedecido con
disolvente.
•
Antes de mezclar, agite suavemente a mano las botellas de los tóneres de Envirobase de Alto Rendimiento
durante unos segundos antes de usarlos. No coloque los tóneres o colores mezclados en un agitador ni los agite
mecánicamente.
•
Los colores de Envirobase de Alto Rendimiento mezclados deben ser agitados completamente a mano antes de
su aplicación. Si no se usan de inmediato, deben volverse a agitar a mano antes de usar.
•
Use filtros de pintura de nailon de 125 micras diseñados especialmente para usar con pinturas en suspensión
de agua.
EB-143SP 12/14
GUÍA DE APLICACIÓN:
Proporciones
de mezcla:
Color Envirobase de Alto Rendimiento
T494/T595**
1 parte
10% por volumen en color sólido
20% por volumen en color metálico / nacarado
30% por volumen en color de capa intermedia
tonalizada
O
Color Envirobase de Alto Rendimiento
Regulador T492*
1 parte
10% por volumen en color sólido
Color Envirobase de Alto Rendimiento metálico / nacarado
Regulador T492*
Disolvente T494/T595**
1 parte
10% por volumen en color metálico / nacarado
+10% por volumen en color metálico / nacarado
Color Envirobase de Alto Rendimiento de capa intermedia
tonalizada
Regulador T492*
Disolvente T494/T595**
1 parte
10% por volumen en color de capa intermedia
tonalizada
+20% por volumen en color de capa
intermedia tonalizada
*El Regulador T492 ha sido específicamente desarrollado como una mejora para el sistema de capas base Envirobase de Alto Rendimiento.
Los bordes delanteros, como parachoques y tableros de instrumentos o los extremos delanteros inferiores pueden ser propensos a golpes con
piedras como cuando se conduce en condiciones extremas, tales como caminos de grava o cuando se someten a un lavado de alta presión. La
adición del Regulador T492 mejorará las propiedades de la capa base. Nota: La aplicación, secado por evaporación y secado generalizado
son los mismos que en el proceso estándar. Si es necesario reducirlo aún más para ajustar la viscosidad, NO agregue T492 adicional; use
solamente T494/T595
** T595 se debe usar solo en condiciones de alta temperatura y baja humedad. Para obtener más información, consulte la guía de
selección de disolvente en la página 6.
Vida útil
Sin activar, 90 días almacenado en envases de plástico sellados. Si se activa, la vida útil es de 2 horas.
Agite bien a mano antes de usar. No lo agite mecánicamente.
Aditivos
T581 (activador opcional) - 10% por volumen después de diluir. Después de la activación, es posible que se
requiera una cantidad adicional de disolvente para diluir el color y lograr los límites de viscosidad de la
mezcla de 23 a 28 segundos.
Ajuste de la pistola
Boquilla:
Viscosidad de rociado:
De 1,2 a 1,4 mm o equivalente
De 23 a 28 segundos, DIN4 a 21 °C (70 °F)
HVLP en el tapón de aire
Convencional en la pistola de rociado
Capa de color
*
*
Presión de rocío
Número de capas
Capa de control
*
*
* La presión de la pistola de rociado variará según el fabricante. Consulte el cuadro sobre ajuste de la pistola
de rociado DOX440 en ppgrefinish.com, pestaña de Índice Envirobase /Hojas de datos técnicos y MSDS
para obtener información sobre la presión establecida por el fabricante.
Todas las reparaciones:
De 2 a 3 capas para cubrir más la capa de control*
Las superficies horizontales podrían requerir dos capas de control, en tanto que las superficies verticales por
lo general requieren una capa de control.
*Nota: En el caso de colores sólidos, no se requiere una capa de control.
Evaporación
21 °C (70 °F)
Entre capas:
De 1 a 2 minutos o hasta que seque con un acabado mate.
Secado final:
Cuando haya terminado, aplique una capa de control y permita
que seque de manera natural. No es necesario secar la capa de
control de manera forzada.
Nota: No use la pistola como secador de aire. Use el equipo de secado de aire apropiado.
2
EB-143SP 12/14
GUÍA DE APLICACIÓN (Cont.):
Tiempos de secado
Sin polvo
21 °C (70 °F)
Cada una de las capas aproximadamente de 2 a 4 minutos
Seco para manipular
21 °C (70 °F)
Aproximadamente de 15 a 20 minutos
Seco para pulir:
21 °C (70 °F)
Aproximadamente de 15 a 20 minutos
Tiempo de encintado
21 °C (70 °F)
5 minutos
Seco para capa transparente
21 °C (70 °F)
15 minutos como mínimo
Nota: Debido a la intensidad del curado IR (infrarrojo), si el revestimiento transparente se cura con luz
infrarroja, primero debe curarse la capa base con IR para eliminar la humedad residual de esta capa.
Recubrimiento/
Nueva capa
Recubra con una capa transparente
compatible
Seque hasta que toda la superficie esté seca al tacto y
tenga una apariencia mate uniforme, o durante 15 minutos*.
Lijado en seco
Use papel lija de grano P1500 europeo o grano 800 de EE. UU.
Recubrir
Después de 24 horas debe aplicarse una capa de Envirobase de
Alto Rendimiento antes del revestimiento transparente. El tiempo
máximo para recubrir es de 48 horas.
*La temperatura, la humedad, el movimiento del aire y la formación de la película afectan los tiempos de
secado. Los mejores resultados se logran al incrementar la temperatura y el movimiento del aire con
formación mínima de película.
MEZCLADO / CAPA INICIAL HÚMEDA
Proporciones
de mezcla:
Aditivo transparente tonalizado T490
4 partes
Disolvente T494 / T595*
1 parte
Para usar como aditivo de mezclado: Agr egue hasta 1 par te igual de la mezcla T490 a 1 par te de la
base de color lista para rociar y difumine en el panel de la mezcla preparada.
o
Para usar como capa inicial húmeda: Aplique 1 capa medianamente liger a de la mezcla T490 al panel
de mezcla y/o por todo el panel de reparación y deje secar. Esta capa tendrá un aspecto azul lechoso mientras
esté húmeda, pero se tornará translúcida cuando seque. Una vez que esté seca, aplique la base de color.
Cerciórese de que cualquiera que sea el material de capa inicial húmeda que se haya aplicado, éste quede
cubierto primero con una capa base o transparente.
*T595 se debe usar solo en condiciones de alta temperatura y baja humedad. Para obtener más información, consulte la guía de
PROCESO NACARADO DE 3 ETAPAS
Primera capa
Proporciones
de mezcla:
Color
Disolvente T492/T494/T595*
Capa nacarada
1 parte
10%**
Color
1 parte
20%**
**Nota: Porcentaje por volumen. Si utiliza el Regulador T492, consulte la página 2 para conocer su uso
apropiado.
* T595 se debe usar solo en condiciones de alta temperatura y baja humedad. Para obtener más información,
consulte la guía de selección de disolvente en la página 6.
3
EB-143SP 12/14
PROCESO NACARADO DE 3 ETAPAS (Cont.):
Viscosidad:
De 23 a 28 segundos DIN4 a 21 °C (70 °F)
Viscosidad y
vida útil:
Vida útil:
90 días almacenado en envases de plástico sellados.
Filtre siempre antes de usar (se recomienda nailon de 125 micras)
Pistola de rociado
y presión de aire
Boquilla:
De 1,2 a 1,4 mm
HVLP
De conformidad
Capa de color
*
*
Capa de control
*
*
* La presión de la pistola de rociado variará según el fabricante. Consulte el cuadro sobre ajuste de la pistola de rociado DOX440 en
ppgrefinish.com, pestaña de Índice Envirobase de Alto Rendimiento/Hojas de datos técnicos y MSDS para obtener información sobre la
presión establecida por el fabricante.
Aplicación:
Primera capa
•
•
•
•
•
Capa nacarada
Aplique capas sencillas hasta lograr la opacidad
deseada.
Deje secar completamente entre capas.
Evite aplicar excesivamente y formar capas
gruesas.
Use equipo de movilización de aire para acelerar
el secado cuando sea necesario. La selección de
métodos de secado dependerá del tipo y tamaño
de la reparación.
En el caso de las bases de colores sólidos, no se
requiere una capa de control.
•
•
•
•
Superficies horizontales y verticales
Aplique capas ligeras sencillas con base en la
verificación de color de los paneles. Deje secar
completamente entre capas.
Aplique la capa de control y déjela secar de
manera natural.
No es necesario secar la capa de control de
manera forzada. La capa de color nacarado no
está diseñada para ofrecer un aspecto opaco.
Evaporación:
Deje secar hasta lograr un aspecto mate uniforme.
Tiempo
de secado:
Espere hasta que la primera capa seque de manera
uniforme antes de aplicar la capa nacarada.
PROCESO DE CAPA INTERMEDIA TONALIZADA DE 3 ETAPAS
Proporciones
Primera capa
de mezcla:
Color
1 parte
20% **
Espere aproximadamente 15 minutos hasta que la
capa nacarada seque de manera uniforme antes de
aplicar el revestimiento transparente.
Capa intermedia tonalizada
Color
Disolvente T492/T494/T595
1 parte
30%**
** Nota: Porcentaje por volumen. Si utiliza el Regulador T492, consulte la página 2 para conocer su uso apropiado.
* T595 se debe usar solo en condiciones de alta temperatura y baja humedad. Para obtener más información, consulte la guía de
Viscosidad y
vida útil
Viscosidad:
De 23 a 28 segundos DIN4 a 21 °C (70 °F)
Vida útil:
90 días almacenado en envases de plástico sellados
Filtre siempre antes de usar (se recomienda nailon de 125 micras)
Pistola de rociado
y presión de aire
Boquilla:
De 1,2 a 1,4 mm*
HVLP
De conformidad
Capa de color
*
*
Capa de control
*
*
* La presión de la pistola de rociado variará según el fabricante. Consulte el cuadro sobre ajuste de la pistola de rociado DOX440 en
ppgrefinish.com, pestaña de Índice Envirobase de Alto Rendimiento/Hojas de datos técnicos y MSDS para obtener información sobre
la presión establecida por el fabricante.
4
EB-143SP 12/14
PROCESO DE CAPA INTERMEDIA TONALIZADA DE 3 ETAPAS (Cont.):
Aplicación:
Primera capa
Capa intermedia tonalizada
•
•
•
Aplique capas sencillas hasta lograr la opacidad
deseada.
Aplique la capa de control sobre la película seca
para un aspecto metálico uniforme.
•
•
•
•
•
Aplique capas ligeras sencillas con base en la
verificación de color de los paneles.
La capa intermedia no está diseñada para ofrecer
un aspecto opaco.
Espere aproximadamente 15 minutos hasta que
la capa intermedia seque de manera uniforme
antes de aplicar el revestimiento transparente.
En el caso de capas intermedias tonalizadas no se
requiere una capa de control.
Pautas para reparaciones menores
Las incrustaciones de polvo u otros defectos en la película de pintura Envirobase de Alto Rendimiento pueden repararse de
la manera siguiente:
1.
2.
3.
4.
5.
Deje que la superficie seque por completo.
Lije el defecto en seco con papel lija grado P1500 o 800 de EE. UU. o más fino o con una almohadilla abrasiva fina, o junto con una cantidad reducida de
removedor de cera y grasa SXA330 como lubricante para lijar.
Elimine el polvo de lijado de la superficie con un chorro fuerte de aire limpio.
Limpie toda la superficie con un trapo humedecido en disolvente SX1070.
Vuelva a recubrir la superficie con Envirobase de Alto Rendimiento de manera normal.
Compatibilidad
Mercados de bajo COV
Mercados de Normas Nacionales
Envirobase de Alto Rendimiento
Tapaporos acromático ECP1x**
Sellador LV acromático ECS2x
Revestimiento transparente En.V™ EC530
Revestimientos transparentes EC700
Revestimientos transparentes serie EC800
Imprimador de secado rápido de suspensión en agua EPW115
Envirobase de Alto Rendimiento
Tapaporos acromático ECP1x**
Sellador LV acromático ECS2x
Sellador acromático ECS6x
Revestimiento transparente En.V EC530
Revestimientos transparentes EC700
Revestimientos transparentes serie EC800
Imprimador de secado rápido de suspensión en agua EPW115
ONECHOICE®
Decapante en aerosol SXA1031* (solo para recortes)
Imprimación de adhesión plástica SXA1050**
Imprimador decapante SX1071**
Removedor de cera y grasa de bajo COV SX1005
Sistema de preparación plástica*** (SU4901, SUA4903)
SU470LV Promotor de adherencia de conformidad 1K
OneChoice
Decapante en aerosol SXA1031* (solo para recortes)
Imprimación de adhesión plástica SXA1050**
SX1057 Tapaporos flexible 2K
SX1060 Imprimador tapaporos laminable 2K
Sistema de preparación plástica*** (SU4901, SU4902, SU4903, SUA4903)
Removedor de cera y grasa de bajo COV SX1005
SWX350 H2O-So-Clean
SU470LV Promotor de adherencia de conformidad 1K
D8188
D8126
D820***
D800x*
D8099**
D8101
D8102
D8115
D8117
D8150
DELTRON®
DPLV305x
DVLP epóxico
NCP280*
DCU2010
DC3010
DC4010
DC4125
Deltron
DPS305x*
DPLV epóxico
K36
DCU2021
DCU2042
DCU2060
DCU2082
DC2000
DC3000
DC4000
DC4125
DX179x***
DPX801***
DPLF*
D8126
D8152
D893
D894
* Para un rendimiento óptimo, puede usarse un imprimador o sellador 2K.
** Para un rendimiento óptimo, puede usarse un sellador 2K
***Debe imprimarse o sellarse.
5
EB-143SP 12/14
Guía de selección de disolventes en suspensión de agua de Envirobase® de Alto Rendimiento
Nota: Usar el disolvente en suspensión de agua T595 con niveles de humedad por encima del 30% puede pr ovocar un secado por evaporación excesivamente lento y el
secado generalizado de la capa base.
No combine los disolventes en suspensión de agua ya que podrían afectar el rendimiento general de la capa base. Dependiendo del nivel de humedad, utilice el disolvente T494 o
T595.
Salud y seguridad
Para obtener información adicional sobre seguridad e instrucciones de manipulación, consulte las hojas de datos de seguridad de
materiales (MSDS) y las etiquetas.
• El contenido de este paquete tal vez deba mezclarse con otros componentes antes de utilizarse. Antes de abrir los paquetes, asegúrese de que
•
•
•
•
•
Limpieza del
equipo
•
•
entiende los mensajes de advertencia en las etiquetas y hojas de datos de seguridad de materiales (MSDS) de todos los componentes, ya que
la mezcla tendrá los riesgos de todas sus partes.
La manipulación y el uso inadecuados, por ejemplo, una técnica de rociado deficiente, controles de ingeniería inadecuados y/o la falta de
equipo de protección personal (PPE) apropiado, pueden provocar condiciones peligrosas o lesiones.
Siga las instrucciones del fabricante del equipo de rociado para prevenir lesiones físicas o incendios.
Proporcione la ventilación adecuada para la salud y para controlar el riesgo de incendio.
Siga la política de la empresa, las hojas de datos de seguridad de materiales (MSDS) y las instrucciones del fabricante del respirador para
elegir y usar la protección respiratoria adecuada. Asegúrese de que los empleados hayan recibido la capacitación adecuada sobre el uso
seguro de respiradores conforme a los requisitos reglamentarios y de la empresa.
Use el equipo de protección personal (PPE) apropiado, por ejemplo, protección para los ojos y la piel. En caso de lesiones, consulte los
procedimientos de primeros auxilios en las MSDS.
Respete siempre todas las precauciones pertinentes y siga las prácticas apropiadas de seguridad e higiene.
Limpie todo el equipo de mezclado inmediatamente después de usarlo, de preferencia con una máquina limpiadora de equipos en suspensión
de agua designada únicamente para este fin, y un enjuague final con disolvente en suspensión de agua. Verifique que todo el equipo esté
completamente seco antes de usarlo o guardarlo.
Almacenamiento y manipulación de Envirobase de Alto Rendimiento
• Los tintes Envirobase de Alto Rendimiento, los colores mezclados Envirobase de Alto Rendimiento y el disolvente en suspensión de agua
•
•
•
•
deben guardarse en un lugar fresco y seco, lejos de las fuentes de calor. Durante el almacenamiento y transporte, la temperatura debe
mantenerse en +5 °C o 41 °F como mínimo y en 49 °C o 120 °F, como máximo. Evite la exposición a la escarcha o a condiciones que
provoquen congelamiento.
Envirobase de Alto Rendimiento debe mezclarse en equipos y envases de plástico, limpios y secos. No use recipientes de mezclado o equipos
de rociado que contengan residuos de disolventes. Los recipientes de mezclado deben ser preferentemente de plástico; si son metálicos, deben
ser de acero inoxidable o tener un revestimiento interno anticorrosivo.
Guarde los residuos en suspensión de agua y con partículas de solvente de manera separada. Un agente experto que cuente con la
certificación apropiada debe manipular todos los residuos en suspensión de agua. Los residuos deben ser eliminados de acuerdo a todas las
leyes y reglamentos federales, estatales, provinciales y locales.
La mezcla del sistema de color de capa base lista para rociar con el activador T581 tiene un punto de ignición por encima de 93 °C (200 °F) y
se puede verter en el flujo para residuos de pinturas solubles en agua destinado para capas base de color (sin activador). Se debe notificar a la
fábrica de eliminación de residuos que el flujo de residuos contiene isocianatos. El activador T581 manipulado independientemente debe
verterse en el flujo de residuos con partículas de solvente.
Los residuos de pintura en suspensión de agua Envirobase de Alto Rendimiento deben separarse de todos los demás residuos y guardarse en
un recipiente revestido cerrado aparte. Los residuos de pintura en suspensión de agua Envirobase de Alto Rendimiento deben ser eliminados
de acuerdo a todas las leyes y reglamentos federales, estatales, provinciales y locales.
6
EB-143SP 12/14
DATOS TÉCNICOS
Rendimiento teórico (RTS), pr opor ciona un espesor de película seca de 12,7 µm (0.5 mils), 274-640 pies2 por galón de EE. UU.
Porcentaje de sólidos por volumen RTS de 8,5 a 20,0%
Combinaciones RTS
Categoría de uso aplicable
Color
Color : T494/T595
Color : T494/T595
Color : T494/T595
Revestimiento de color Revestimiento de color Revestimiento de color Revestimiento de color
Proporción
Empaquetado
1 : 10%
1 : 20%
1 : 30%
Densidad (g/l)
De 991 a 1204
De 992 a 1186
De 992 a 1171
De 992 a 1156
Densidad (lb/gal. de EE.UU.)
De 8,27 a 10,05
De 8,28 a 9,90
De 8,28 a 9,77
De 8,28 a 9,65
De 47 a 120
De 44 a 111
De 43 a 103
De 41 a 97
COV real (lb/gal de EE. UU.)
De 0,39 a 1,00
De 0,37 a 0,93
De 0,36 a 0,86
De 0,34 a 0,81
COV reglamentario (g/l)
De 207 a 395
De 213 a 401
De 219 a 407
De 225 a 419
COV reglamentario (lb/gal de
EE.UU.)
De 1,73 a 3,30
De 1,78 a 3,35
De 1,83 a 3,40
De 1,88 a 3,50
% de peso de volátiles
De 60,42 a 84,97
De 63,42 a 86,29
De 66,01 a 87,44
De 68,26 a 88,40
% de peso de agua
De 51,37 a 74,99
De 54,94 a 77,09
De 58,00 a 78,85
De 60,05 a 80,33
0,0
0,0
0,0
0,0
De 61,98 a 77,47
De 65,29 a 79,41
De 68,03 a 80,96
De 70,26 a 82,22
0,0
0,0
0,0
0,0
Color : T494/T595 :
T581
Color : T494/T595 :
T581
Color : T494/T595 :
T581
T490 : T494/T595
COV real (g/l)
% de peso de exentos
% de volumen de agua
% de volumen de exentos
Combinaciones RTS
Revestimiento de
color
Revestimiento de color Revestimiento de color
Capa de acabado
uniforme
Proporción
1 : 10% : 10%
1 : 20% : 10%
1 : 30% : 10%
4:1
Densidad (g/l)
De 998 a 1170
De 999 a 1158
De 998 a 1146
992
De 8,33 a 9,76
De 8,34 a 9,66
De 8,33 a 9,56
8,28
De 70 a 119
De 67 a 112
De 63 a 105
91
De 0,58 a 0,99
De 0,56 a 0,94
De 0,53 a 0,88
0,76
De 252 a 359
De 256 a 370
De 261 a 373
380
EE.UU.)
De 2,1 a 3,0
De 2,14 a 3,09
De 2,18 a 3,11
3,17
De 61,4 a 80,5
De 64,0 a 82,0
De 66,2 a 83,3
85,7
% de peso de agua
De 51,2 a 70,0
De 54,3 a 72,1
De 57,0 a 74,0
76,6
0,0
0,0
0,0
0,0
De 60,0 a 72,1
De 63,0 a 74,1
De 65,5 a 75,8
76,1
0,0
0,0
0,0
0,0
COV real (g/l)
7
EB-143SP 12/14
Combinaciones RTS
Color : T492
Color : T492 : T494/T595
Color : T492 : T494/T595
Revestimiento de color
100 : 10%
100 : 10% : +10%
100 : 10% : +20%
Densidad (g/l)
De 995 a 1056
De 996 a 1050
De 996 a 1045
De 8,30 a 8,81
De 8,31 a 8,76
De 8,31 a 8,72
De 55 a 102
De 52 a 95
De 48 a 87
De 0,46 a 0,84
De 0,43 a 0,79
De 0,40 a 0,73
EE.UU.)
De 216 a 403
De 219 a 405
De 223 a 407
De 1,80 a 3,36
De 1,83 a 3,38
De 1,86 a 3,40
De 75,9 a 86,3
De 77,9 a 87,5
De 79,9 a 88,7
% de peso de agua
De 70,8 a 80,1
De 73,0 a 81,6
De 75,2 a 83,1
0,0
0,0
0,0
De 72,1 a 80,3
De 74,2 a 81,7
De 76,3 a 83,1
0,0
0,0
0,0
Proporción
COV real (g/l)
Información sobre emergencias médicas y control de derrames: (412) 434-4515; en Canadá al (514) 645-1320
Los materiales descritos están diseñados para ser aplicados únicamente por personal profesionalmente capacitado, utilizando el equipo apropiado, y sin la intención de
ser vendidos al público en general. Los productos mencionados pueden ser peligrosos y deberán usarse únicamente de acuerdo a las instrucciones, al tiempo que se
respetan todas las precauciones y sistemas de advertencia enumerados en la etiqueta. Las declaraciones y los métodos descritos se basan en las mejores prácticas e
información conocidas a la fecha por PPG Industries. Los procedimientos de aplicación mencionados son sugerencias únicamente y no deben ser considerados como
representaciones o garantías del desempeño, resultados o idoneidad de cualquier uso deseado. PPG Industries no garantiza que no se incurra en incumplimiento de
patentes ante el uso de cualquier fórmula o proceso descrito en el presente documento.
Acabado Automotriz PPG
800.647.6050
PPG Canada Inc.
888.310.4762
Búsquenos en Internet:
www.ppgrefinish.com
El logotipo de PPG Logo, Bringing innovation to the surface, Envirobase, OneChoice, Deltron, Global Refinish System, En.V y H2O-So-Clean son
marcas comerciales de PPG Industries Ohio, Inc.
Xirallic es una marca comercial registrada de Merck Kgaa.
8
EB-143SP 12/14
OC-9
Waterborne Pre-Cleaner
SWX350
H2O-So-Clean™ Waterborne Pre-Cleaner
SWX350 H2O-So-Clean™ is a superior
waterborne surface cleaner used for
removing most contaminations including
wax and grease, mold release agents and
sanding dust.
SWX350 is commonly referred to as simply
“O-so-clean” thanks to its excellent cleaning
ability. It is compliant in the most stringent
VOC markets with an ultra low 0.21 VOC.
Features
·Packaged ready for use
·Produces consistent results
Required Products
· SWX350 H O-So-Clean™ Waterborne Pre-Cleaner
2
Compatible Products
Advantages
· Can be used with PPG or
Nexa Autocolor systems
Benefits
·Customer satisfaction
· SWX350 Waterborne Pre-cleaner is for use with PPG and
Nexa Autocolor brand products.
Compatible Substrates
· OEM Surfaces
· Cured and Dried Automotive Surfaces
· Ferous and non-ferous metals
· Automotive Plastics
H2O-So-Clean™ Waterborne Pre-Cleaner
SWX350
Application Data
Application:
· SWX350 is packaged ready for use.
· Apply a generous amount of SWX350 on the surface with a clean cloth or a hand held spray bottle and wipe the surface clean. This initial step floats the contaminants to the surface.
Use a second clean cloth to wipe the surface clean and remove the contaminants.
For maximum results, wipe dry with clean cloth while the surface is still wet, to eliminate smearing of contaminants.
·
·
Technical Data:
Color
Intended Use
Packaged (ready to use) VOC content
Density
Flashpoint (PMCC)
Clear
Solvent (Substrate Cleaner)
0.16 lbs/gal (19 g/L)
8.15 lbs/gal
62°F (17°C)
Before opening the packages, be sure you understand the warning messages on the labels of all components, since the mixture will have the hazards of all its parts. Improper spray technique may result in a hazardous condition. Follow spray equipment manufacturer’s instructions to prevent personal injury or fire. Follow directions for respirator use. Wear eye
and skin protection. Observe all applicable precautions.
Important:
See material Safety Data Sheet and Labels for additional safety information and handling instructions.
EMERGENCY MEDICAL OR SPILL CONTROL INFORMATION (412) 434 -4515. IN CANADA (514) 645-1320
Materials described are designed for application by professional, trained personnel using proper equipment and are not intended for sale to
the general public. Products mentioned may be hazardous and should only be used according to directions, while observing precautions
and warning statements listed on label. Statements and methods described are based upon the best information and practices known to
PPG Industries. Procedures for applications mentioned are suggestions only and are not to be construed as representations or warranties as
to performance, results, or fitness for any intended use, nor does PPG Industries warrant freedom from patent infringement in the use of any
formula or process set forth herein.
PPG Industries
World Leaders in Automotive Finishes
PPG Industries
1-800-647-6050
www.ppgrefinish.com
PPG Canada Inc.
Mississauga, Ontario, Canada L5J 1K5
1-888-310-4762
Part No. OC-9 11/09
P-246
DELTRON® Ultra Velocity Clearcoat
DC2000
DC2000 is an ultra velocity, high quality
clearcoat, specifically developed to enhance
productivity in air-dry collision repair facilities
and also reduces energy cost in facilities with
baking booths.
Deltron Ultra Velocity Clearcoat is designed for
use on repairs of 1- 4 panels.
DC2000 offers extremely fast flash, polish and
air dry times without sacrificing durability or
appearance.
Features
● Fast air dry
● Sand and buff in 30 minutes or less
Advantages
● Faster throughput
● Performs well in all booth types
● Speeds up assembly and delivery time
Benefits
● Increased production
● Reduces cycle times
Compatible Surfaces
●
●
●
●
Deltron 2000 (DBC) Basecoat
GLOBAL REFINISH SYSTEMl® BC Basecoat
Fully cured and sanded OEM and refinish paints
Required Products
DC2000 Ultra Velocity Clearcoat
DCH2015 Hardener
DR220 Medium Temperature Accelerated Reducer (70°- 85°F / 21°- 29°C)
DT885 Mid Temperature Thinner (75 - 90°F / 24° - 32°C)
DT895 High Temperature Thinner (85 - 95°F / 29° - 35°C)
DT898 Very High Temperature Thinner (95°F and above / 35°C and above)
D871 Medium Thinner (65° - 77°F /18° - 25°C )
D872 Slow Thinner (77° - 95°F / 25° - 35°C )
D873 Very Slow Thinner (95°F and above / 35°C and above)
DC2000
Directions For Use
Preparation:
Refer to the specific product Information bulletin of the color system for its application, dry times,
and blend recommendations.
Mixing Ratios:
DC2000
4 parts
:
:
DCH2015
1 part
:
:
DR220/DT8xx/D8xx
½ to 1 part
Pot Life:
2 hours at 70ºF (21ºC)
Additives:
DC2000
DX814
Flexibilizer
DCH 2015
4 parts
:
1 part
DC2000
:
DCH 2015
4 parts
:
1 part
DX73
Fisheye
Eliminator
DR220/DT8xx/D8xx
+
10%
DR220/DT8xx/D8xx :
DX73
:
:
½ to 1 part
DX814
½ to 1 part
+
1 oz. to
RTS qt.
For flattening recommendations, see OneChoice® bulletin OC-2
Application Coats:
Apply:
2 medium wet coats with no flash between coats
Air Pressure:
HVLP:
Compliant:
Conventional:
10 psi at the air cap
Note : For best overall results, refer to spraygun manufacturers recommendation for inlet air pressures.
Spray Gun Set-up:
Fluid Tip:
Film Build Per Wet Coat
Dried Film Build Per Coat:
Page 2 P-246
2 - 3 mils
1 - 1.5 mils
Directions For Use
Drying Times:
Between Coats:
70ºF / 21ºC
No flash required
Dust Free:
70ºF / 21ºC
9-12 minutes
Tape Time:
70ºF / 21ºC
1 hour
Air Dry to Re-assemble:
70ºF / 21ºC
1 hour
Force Dry:
140ºF / 60ºC
Not Recommended
IR
Not Recommended
Polishing:
Air Dry
70ºF / 21ºC
25- 30 minutes
Repair and Recoat:
2 - 3 hours air dry 70ºF (21ºC)
DC2000 must be sanded before recoating
with primer, color or clear.
Equipment Cleaning:
Spray guns, gun cups, storage pots, etc., should be cleaned thoroughly
after each use with any appropriate PPG general purpose solvent.
Page 3 P-246
DC2000
Deltron Ultra
Velocity Clearcoat
Technical Data:
Important:
VOC less exempt solvents (Applied 4:1:1)
4.03 - 4.17 lbs/gal (483 – 500 g/l)
VOC less exempt solvents w/DX814 (Applied 4:1:1+10%)
VOC less exempt solvents w/DX73 (Applied 4:1:1+1 oz. RTS qt.)
VOC less exempt solvents w/SU4985 (Applied X:X:X:X)
4.37 - 4.44 lbs/gal (524 – 532 g/l)
4.17 - 4.27 lbs/gal (500 – 512 g/l)
5.04 - 5.26 lbs/gal (604 – 630 g/l)
Total Solids by Volume (Applied 4:1:1)
35.1%
Sq. Ft Coverage / US Gal (Applied 4:1:1)
564 @ 1 mil, 100% transfer efficiency
The contents of this package must be blended with other components before the product can be
used. Before opening the packages, be sure you understand the warning messages on the labels of
all components, since the mixture will have the hazards of all its parts. Improper spray technique
may result in a hazardous condition. Follow spray equipment manufacturer’s instructions to
prevent personal injury or fire. Follow directions for respirator use. Wear eye and skin
protection. Observe all applicable precautions.
EMERGENCY MEDICAL OR SPILL CONTROL INFORMATION (412) 434-4515; IN CANADA (514) 645-1320
Materials described are designed for application by professional, trained personnel using proper equipment and are not
intended for sale to the public. Products mentioned may be hazardous and should only be used according to directions,
while observing precautions and warning statements listed on label. Statements and methods described are based upon the
best information and practices known to PPG Industries. Procedures for applications mentioned are suggestions only and
are not to be construed as representations or warranties as to performance, results, or fitness for any intended use, nor does
PPG Industries warrant freedom from patent infringement in the use of any formula or process set forth herein.
PPG Industries
1-800-647-6050
PPG Canada Inc.
2301 Royal Windsor Drive Unit #6
1-888-310-4762
The PPG logo, Deltron, Envirobase, Global Refinish System, OneChoice and Bringing innovation to the surface are registered trademarks of
PPG Industries Ohio, Inc.
www.ppgrefinish.com
Part No. P-246, 12/13
Cleaners
December 2014
Description
UltraPrep Surface Cleaner is a waterbased surface cleaner with low VOC content. UltraPrep Surface Cleaner is
used to ensure removal of all kinds of contamination from the substrate prior to paint application.
Suitable Substrates
Steel
Stainless Steel
Zinc Coated Steel
Aluminum
Existing Finishes
Plastic Substrate
Cleaning technique
After washing the car or the surface of the body panel under treatment, wet a clean cloth with the
UltraPrep Surface Cleaner and clean the surface under treatment. Immediately thereafter, wipe the
surface thoroughly dry with high quality absorbent surface cleaning cloths.
Always use two cloths, as one cloth will merely shift rather than remove dirt and grease.
Do not allow the surface cleaner to evaporate on substrate or the contamination on the surface will
remain.
Wipe the substrate thoroughly dry before the surface cleaner evaporates.
The purpose of surface cleaning is to remove residual grease, oil, wax, silicones, sand, etc. If this
is not done, residual contaminant will remain in scratch marks during sanding. Adhesion of the
paint system subsequently applied to the contaminated surface will be poor and could delaminate.
o Replace cloths being used for cleaning regularly by clean ones. Instead of placing used
(wet) rags in a sealed container place them on the floor grating so that the solvents can
evaporate, then place the dried cloths in the regular dustbin.
Point of attention on surface cleaning:
Salt residue and blistering:
With all cleaning activities: once the surface under treatment has been cleaned, it must never be
touched with the bare hand; as salts, moisture and oils can be transferred to the prepared surface
which may result in delamination or blistering problems. It is particularly important that hand
protecting barrier creams are never used near an automobile that is to be refinished.
Should you still have touched a sanded and cleaned surface with bare hands; clean it again with
first one of the solvent borne and next with one of the water borne cleaners again according the
recommended cleaning technique.
Truck body constructions:
It is important to prevent dirt residues from getting into construction joints of vans, lorries, etc.
during cleaning . They might cause adhesion problems when the paint is applied. Vertically fitted
parts should, therefore, first be the surface should be cleaned from the bottom upwards and
subsequently from the top downwards.
1/2
Cleaners
December 2014
Point of attention on surface cleaning continued):
Cleaning and condensation on metal surfaces:
After a surface has been cleaned, solvent will evaporate. Heat needed for
evaporation is withdrawn from that surface, making it colder than the surrounding atmosphere, which results
in (often not visible) condensation on the surface. Allow the moisture sufficient time to evaporate.
The first coat of paint can be applied as soon as the surface has re-gained the temperature of the
surrounding atmosphere. Earlier application of the coat may lead to adhesion problems.
The same problem may arise if a vehicle is transferred from a cold room to a warm one or from outdoors to
indoors. Allow vehicles a minimum of one hour to acclimatize. Double-walled vehicles (and certainly
insulated ones) require some hours to acclimatize.
Health and Safety
Akzo Nobel Car Refinishes recommends providing adequate ventilation during surface cleaning with any of
the mentioned cleaners. Where reasonably practicable, this should be achieved by the use of local exhaust
ventilation and good general extraction. If these are not sufficient to maintain concentrations of particulates
and solvent vapours below the OEL, suitable respiratory protection must be worn.
Besides respiratory protection, always wear solvent resistant gloves while surface cleaning even though
working with a low solvent degreaser. This will reduce the risk of cleaning solvents being absorbed into the
skin and prevent salts and oils on your hands from contaminating the surface to be refinished.
VOC
The VOC content of this product in ready to use form is 0.00 g/liter.
Product storage
Product shelf life is determined when products are stored unopened at 70°F (20°C).
Avoid too much temperature fluctuation.
o Product shelf life is 1 year
AkzoNobel Automotive and Aerospace Coatings, Inc
Address: 3587 Parkway Lane, Norcross, GA 30092
Tel: 770-662-8464
IMPORTANT NOTE The information in this data sheet is not intended to be exhaustive and is based on the present state of our knowledge and on current
laws: any person using the product for any purpose other than that specifically recommended in the technical data sheet without first obtaining written
confirmation from us as to the suitability of the product for the intended purpose does so at his own risk. It is always the responsibility of the user to take all
necessary steps to fulfill the demands set out in the local rules and legislation. Always read the Material Data Sheet and the Technical Data Sheet for this
product if available. All advice we give or any statement made about the product by us (whether in this data sheet or otherwise) is correct to the best of our
knowledge but we have no control over the quality or the condition of the substrate or the many factors affecting the use and application of the product.
Therefore, unless we specifically agree in writing otherwise, we do not accept any liability whatsoever for the performance of the product or for any loss or
damage arising out of the use of the product. All products supplied and technical advices given are subject to our standard terms and conditions of sale. You
should request a copy of this document and review it carefully. The information contained in this data sheet is subject to modification from time to time in the
light of experience and our policy of continuous development. It is the user's responsibility to verify that this data sheet is current prior to using the product.
Brand names mentioned in this data sheet are trademarks of or are licensed to Akzo Nobel.
Head Office
2/2

Product Information

Transcripción

Documentos relacionados