Operating Manual

Transcripción

Operating Manual

SmartWash er
®
Operating Manual
Ozzy ®
Model
SW-37
Mobile Heavyweight Parts Washer
MANUEL D’UTILISATION
Modèle SW-37
MANUAL DE OPERACIÓN
Modelo SW-37
v1-14
the sustainable solution
Printed On Recycled Paper
SmartWash er
SmartWash er
®
Ozzy ®
SmartWash er
®
Ozzy ®
Operating Manual
®
Ozzy ®
Mode d’Emploi
Manual de Operacione
PLEASE READ THIS INSTRUCTION
MANUAL CAREFULLY AND COMPLETELY
TO
ENSURE
THAT
YOUR
NEW
SMARTWASHER® WILL OPERATE AT ITS
MAXIMUM EFFECTIVENESS.
VEUILLEZ LIRE ATTENTIVEMENT ET
COMPLÈTEMENT CE MANUEL
D'INSTRUCTIONS POUR ASSURER
QUE VOTRE NOUVEAU
SMARTWASHER ® FONCTIONNERA À
SON MAXIMUM D'EFFICACITÉ.
LEA CUIDADOSAMENTE ESTE MANUAL
DE INSTRUCCIONES EN SU TOTALIDAD,
A FIN DE ASEGURAR QUE SU NUEVO
SMARTWASHER® FUNCIONARÁ CON SU
MÁXIMA EFECTIVIDAD.
SAFETY INSTRUCTIONS:
INSTRUCTIONS DE SÉCURITÉ:
When using your SmartWasher®,
basic safety precautions should
always be followed, including
the following:
Read ALL Instructions:
Pour l'utilisation de votre
SmartWasher®, des précautions
de
sécurité
élémentaires
doivent toujours être prises,
incluant ce qui suit:
Lisez TOUTES ces Instructions:
1. Care must be taken as burns can occur from
1. Il faut faire attention car on peut se brûler en
2. Do not operate SmartWasher with damaged
2. Ne le faites pas fonctionner avec son cordon
touching hot parts.
touchant des pièces chaudes.
INSTRUCCIONES DE SEGURIDAD:
Cuando use su SmartWasher®
debe observar siempre las
precauciones básicas de seguridad, incluidas las siguientes:
Lea Todas Las Instrucciones:
1. Se debe tener cuidado de las quemaduras,
que pueden ocurrir cuando se tocan piezas
calientes.
cord or if the equipment has been dropped or
damaged
until it has been examined by a
qualified service person.
secteur endommagé ou si l'équipement est
tombé ou a été abîmé, jusqu'à ce qu'il ait été
examiné par du personnel de service
qualifié.
2. No haga funcionar el SmartWasher si el
3. Do not let a cord hang over the edge of the
3. Ne laissez pas le cordon pendre sur le
3. No deje que el cordón de alimentación
4. Si une extension du raccordement secteur
4. Si se necesita un cordón de extensión, debe
table, bench, or counter or come in contact
with hot manifolds or moving fan blades.
4. If an extension cord is necessary, a cord with
a current rating equal to or more than that of
the equipment should be used. Cords rated
for current lower than the equipment may
overheat. Care should be taken to arrange
the cord so that it will not be tripped over or
pulled. (Must be rated a minimum of
15A/110V (5A/220V))
5. Unplug equipment from electrical outlet when
not in use for an extended period of time.
Never use the cord to pull the plug from the
outlet. Grasp plug and pull to disconnect.
6. To reduce the risk of fire, do not operate
equipment in the vicinity of open containers
of flammable liquids (gasoline).
7. Adequate ventilation should be provided when
working on operating internal combustion
engines.
8. Keep hair, loose clothing, fingers, and all
parts of body away from moving parts.
est nécessaire, il faut utiliser une rallonge
supportant le même courant ou plus que
celui tiré par l'équipement, sinon il y aurait
surchauffe de cette rallonge. Il faut prendre
des précautions pour que le cordon ne fasse
pas trébucher et ne soit pas tiré. La capacité
minimum doit être de 15 A sous 120 V (ou 5
A en 220 V).
5. Débranchez l'équipement de la prise secteur
quand il n'est pas en utilisation pendant une
période longue. Ne tirez jamais sur le cordon
pour débrancher sa prise de la fiche secteur.
Il faut saisir directement la fiche pour la
retirer.
6. Pour réduire le risque de départ d'incendie,
ne faites pas fonctionner l'équipement à
proximité de bidons de liquides inflammables
ouverts (comme de l'essence).
7. Une ventilation adéquate doit être fournie en
travaillant avec des moteurs à combustion
en fonctionnement.
8. Gardez la chevelure, les vêtements lâches,
9. To reduce the risk of electric shock, do not
use on wet surfaces or expose to rain.
10. Use SmartWasher only as described in this
manual. Use only attachments and parts
recommended by ChemFree.
11. ALWAYS
WEAR SAFETY GLASSES.
Everyday eyeglasses only have impact
resistant lenses, they are not safety glasses.
12. It is good practice to wear gloves whenever
using industrial cleaning fluids.
rebord d'une table ou d'un plan de travail, ni
entrer en contact avec des collecteurs
chauds ou des pales de ventilateur en
marche.
les doigts et toutes les parties du corps, à
l'écart de toutes les pièces mobiles.
9. Pour
réduire le risque de commotion
électrique, n'utilisez pas l'équipement sur
des surfaces mouillées ou en l'exposant à la
pluie.
cordón de alimentación eléctrica está
dañado, o ñado, hasta que lo examine una
persona experta de servicio.
eléctrica cuelgue sobre el borde de la mesa,
banco o cubierta, o entre en contacto con
colectores calientes o paletas móviles de
ventilador.
utilizarse uno con una especificación de
corriente igual o mayor que el del equipo.
Los cordones de alimentación eléctrica
diseñados para corrientes menores que las
del equipo, pueden sobrecalentarse. Se
debe cuidar la disposición del cordón, para
que no se pueda tropezar con él o tirar de
él. (La especificación mínima debe ser 15
A/110 V, o 5 A/220 V).
5. Desenchufe el equipo del tomacorriente
eléctrico cuando no lo use por un período
de tiempo prolongado. Nunca use el cordón
para extraer el enchufe del tomacorriente.
Sujete el enchufe y tire de él para
desconectarlo.
6. Para reducir el riesgo de incendio, no haga
funcionar el equipo en las cercanías de
recipientes abiertos de líquidos inflamables
(gasolina).
7. Al trabajar en motores de combustión
interna
en
funcionamiento,
debe
proporcionarse una ventilación adecuada.
8. Mantenga su cabello, ropas sueltas, dedos
y el resto de su cuerpo lejos de las piezas
móviles.
9. Para reducir el riesgo de choque eléctrico,
no use el equipo sobre superficies mojadas
ni lo exponga a la lluvia.
10. N'utilisez le SmartWasher que de la manière
10. Use el SmartWasher únicamente de la
11. PORTEZ
EN
PERMANENCE
DES
LUNETTES DE SÉCURITÉ. Les simples
lunettes de vue n'ont que des verres
résistlunettes de protection.
11. USE SIEMPRE GAFAS DE SEGURIDAD.
12. C'est une bonne habitude que de porter des
12. Es una buena práctica usar guantes toda
décrite dans ce manuel. N'utilisez que des
accessoires et des pièces que ChemFree
recommande.
gants pour manier des fluides de nettoyage
industriel.
manera descrita en este manual. Use
únicamente
accesorios
y
piezas
recomendadas por ChemFree.
Las gafas de uso diario sólo tienen lentes
resistentes al impacto, y no son gafas de
seguridad.
vez que se utilicen líquidos de limpieza
industriales.
ChemFree Technical Support : 770-564-5580 www.chemfree.com
FREE OZZY T-SHIRT
WARRANTY REGISTRATION CARD REGISTER AND GET A FREE T-SHIRT
complete AND mail, OR register online: www.chemfree.com
company name:
FREE OZZY T-SHIRT
T-SHIRT SIZE /CIRCLE:
L
XL XXL
DESCRIBE TYPE OF BUSINESS:
contact/department:
(auto repair, fleet maintenance, government, manufacturing...)
address:
HOW OFTEN DO YOU USE A PARTS WASHER?
city:
state:
circle one
zip:
daily
weekly
monthly
HOW MANY PARTS WASHERS DO YOU HAVE?
HOW DID YOU HEAR ABOUT THE SMARTWASHER PRODUCTS?
phone:
model number:
tv
SW-
google
magazine
sales representative
other
WHO DID YOU PURCHASE YOUR SMARTWASHER THROUGH?
SERIAL NUMBER
email:
OZZYJUICE SOLUTION #
YES! I would like to receive e-mail notifications about new products, promotions/industry news
CAMISETA GRATUITA DE OZZY T-SHIRT OZZY GRATUIT
Cut Along This Line
ENREGISTREMENT DE GARANTIE ENREGISTRER Et Obtenir Une T-shirt Gratuit
enregistrer: www.chemfree.com
T-SHIRT OZZY GRATUIT
L
TAILLE DU T-SHIRT:
nom de l’entreprise:
nom et titre du contact:
XL XXL
DÉCRIVIZ VOTRE TYPE D’ACTIVITÉ:
(réparation automobile, armée, fabrication.............)
adresse postale:
A QUELLE FRÉ QUENCE UTILISEZ-VOUS UNE MACHINE À LAVER DES PIÈCES?
ville:
état/province:
entourez une réponse
hebdomadairement
quotidiennement
code:
mensuellement
COMBIEN POSSÉDEZ-VOUS DE NETTOYEURS DE PIÈCES?
COMMENT AVEZ-VOUS ENTENDU PARLER DES PRODUITS SMARTWASHER?
téléphone:
nombre modèle:
tv
SW-
google
magazine
agent commercial
autre
CHEZ QUI AVEZ-VOUS ACHETÉ CETTE UNITÉ?
NUMÉRO DE SÉRIE
DE SOLUTION D’OZZYJUICE
OUI! j’accepte de recevoir par courriel des notifications sur les nouveaux produits, les
promotions spéciales et des nouvelles de l’industrie.
adresse électroniquel:
Cut Along This Line
REGISTRO DE GARANTÍA REGÍSTRESE Y Obtenga Una Camiseta Gratis
registro: www.chemfree.com
CAMISETA OZZY GRATIS¡
TAMAÑO DE LA CAMISETA:
nombre de la compañia:
nombre/titulo de contacto:
L
XL
XXL
DESCRIBA SU TIPO DE NEGOCIO:
(reparación de autos, militar, fabricación......)
dirección:
¿CUÁN FRECUENTEMENTE UTILIZA USTED UNA LAVADORA DE PIEZAS?
ciudad:
estadó:
código postal:
encierre en círculo una de las opciones
semanalmente
diariamente
mensualmente
¿CUÁNTOS LAVADORES DE PIEZAS TIENE?
¿CÓMO SE ENTERÓ DE LOS PRODUCTOS SMARTWASHER?
teléfono:
número de modelo:
tv
SWNÚMERO DE SERIE
dirección de e-maill:
google
revista
representante de ventas
otro
¿A TRAVÉS DE QUIÉN COMPRÓ SU LAVADOR DE PIEZAS?
LA SOLUCIÓN DE OZZYJUICE
SÍ ! Quiero recibir notificaciones por e-mail sobre nuevos productos, promociones
especiales y noticias de la industria.
SmartWash er
®
Place
Stamp
Here
Ozzy ®
ChemFree Corporation
8 Meca Way
Norcross, GA 30093-2919
8 Meca Way
WARRANTY REGISTRATION
SmartWash er
®
Ozzy ®
Coller le
timbre ici
8 Meca Way
8 Meca Way
ENREGISTREMENT DE GARANTIE
SmartWash er
®
Ozzy ®
Coloque la
estampilla
aquí
8 Meca Way
8 Meca Way
REGISTRO DE GARANTÍA
Félicitations!
¡Felicitaciones!
You
have
purchased
the
state-of-the-art
SmartWasher® Bioremediating Parts Washing
System. The SmartWasher systems combine a
powerful cleaning solution with the bioremediating
power of specially-bred Ozzy® microbes. Once a
SmartWasher has been properly installed and
activated, it is literally ALIVE!
Vous avez acheté un SmartWasher® d'avant garde.
Nos systèmes SmartWasher de lavage de pièces
combinent une puissante solution de nettoyage avec
la puissance de biorestauration de notre élevage
spécial de microbes Ozzy® microbes. Une fois que le
SmartWasher a été correctement installé et activé, il
est littéralement VIVANT!
Usted ha comprado el sistema SmartWasher® con
tecnología de avanzada. Los sistemas de lavado de
piezas SmartWasher combinan una potente solución
limpiadora con el poder biocorrector de los microbios
Ozzy® desarrollados especialmente. Una vez que el
SmartWasher se ha instalado y activado correctamente, está literalmente VIVO.
Your SmartWasher®
IS safe and easy to use
USES the latest in bioremediation technology
to eliminate hazardous liquid waste
HELPS deregulate and detoxify your
workplace and reduce government paperwork
SAVES you money
Votre SmartWasher®
Su SmartWasher®
Table of Contents
Table des Matières
Índice
Warranty Registration: .... separate insert
(second page)
ES seguro y fácil de usar
UTILIZA lo más reciente en tecnología de biocorrección para eliminar residuos líquidos peligrosos
AYUDA a liberar de regulaciones y eliminar la
toxicidad de su lugar de trabajo, y a reducir el
papeleo en las oficinas del gobierno
AHORRA su dinero
Instructions de sécurité: ...... intérieur de
Instrucciones de seguridad: ...... la portada
Enregistrement de garantie: .. insert séparé
(deuxième page)
Registro de garantía: .........inserto separado
(segunda página)
couverture avant
interior de
Installation et mise en œuvre: ................
1
Instalación y preparación: ...........................
1
Installation and Setup Cont.: ..............
2
Installation et mise en œuvre suite: .......
2
Instalación y preparación (cont.): ..............
2
Proper Use, Care And Maintenance: ..
3
Utilisation, soins et entretien corrects: ..
3
Uso, cuidado y mantenimiento correctos: ..
3
Frequently Asked Questions: .............
4
Questions souvent posées: ....................
4
Preguntas frecuentes: .............................
4
Frequently Asked Questions: .............
5
Questions souvent posées: ....................
5
Preguntas frecuentes: .............................
5
Trouble Shooting: ................................
6
Dépannage: ...............................................
6
Localización de fallas: .............................
6
Trouble Shooting Cont.: ......................
7
Dépannage suite: .....................................
7
Localización de fallas (cont.): .................
7
Trouble Shooting Cont.: ......................
8
Dépannage suite: .....................................
8
Localización de fallas (cont.): .................
8
Sink Diagram, Model SW-37: ..............
9
Schéma de puits, modèle SW-37: ...........
9
Diagrama de la cavidad, modelo SW-37:....
9
Schéma de socle, modèle SW-37: ..........
10
Diagrama de la base, modelo SW-37: .........10
Replacement Parts............................... 11
Pièces De Rechange: ................................ 11
Piezas De Repuesto: ............................... 11
My SmartWasher® Records
Mon SmartWasher® Enregistre
Mi SmartWasher® Registra
Change OzzyMat Calendar
Calendrier De Remplacement D’ozzymat
Calendario de cambio de la alfombrilla OzzyMat
Disclaimer and
Equipment Warranty: .. Inside Back Cover
Déni de responsabilité et garantie
Exención de responsabilidad y Garantía
del equipo: ........... Interior De La Contraportada
The SmartWasher® is designed to safely and
effectively remove oil and grease from
automotive and industrial parts. It replaces
hazardous solvent parts washers with
aqueous-based degreasing solutions called
and
microbe
impregnated
OzzyJuice®
particulate traps called OzzyMats™.
The
microbes impregnated into the OzzyMat come
to life in the OzzyJuice and break down, or
“eat”, the grease, oil and other contaminants in
the solution leaving by-products of harmless
carbon dioxide and water - leaving nothing
hazardous to haul away. OzzyJuice is an
award winning, pH neutral, non-caustic,
non-flammable and biodegradable degreasing
solution. Working in concert with our microbes
(Ozzy®) these superior products help eliminate
or greatly reduce your need to dispose of
hazardous waste, giving you all the
performance you are used to in a typical solvent
parts washer without all the hazards and
hassles. You have made a great decision.
Le SmartWasher® est conçu pour éliminer
l'huile et la graisse sans risques et efficacement des pièces automobiles et industrielles. Il
remplace les solvants dangereux des autres
laveurs de pièces par des solutions appelées
OzzyJuice® et des tapis imprégnés de
microbes appelés OzzyMat™. Ces microbes
venant de l'OzzyMat s'animent dans
l'OzzyJuice et dissocient ou “mangent” la
graisse, les huiles et d'autres contaminants
dans la solution, en libérant comme
sous-produits sans danger du dioxyde de
carbone et de l'eau. Il n'y a donc rien de
dangereux à jeter à la fin. L'OzzyJuice est une
solution de dégraissage qui a été primée, son
pH est neutre et elle est ininflammable et
biodégradable. En travaillant de concert avec
nos microbes (Ozzy®) ces produits supérieurs
aident à éliminer ou à notablement réduire
votre besoin de mettre des déchets au rebut,
en vous procurant la performance dont vous
avez l'habitude des laveurs de pièces aux
solvants habituels, sans leurs risques et
tracas. Vous avez pris une sage décision.
SmartWash er
SmartWash er
El
SmartWasher®
está
diseñado
El
SmartWasher® está diseñado para eliminar en
forma segura y efectiva el aceite y la grasa de
las piezas automotrices e industriales. Reemplaza a los peligrosos limpiadores de piezas a
base de solventes por soluciones desengrasantes de base acuosa llamadas OzzyJuice®, y
trampas de partículas impregnadas con
microbios llamadas OzzyMats™. Los microbios
impregnados en la OzzyMat cobran vida en el
OzzyJuice y descomponen o ‘comen’ la grasa, el
aceite y otros contaminantes en la solución,
dejando subproductos inofensivos -dióxido de
carbono y agua- sin nada peligroso que deba
retirarse mediante un transporte. OzzyJuice es
una solución desengrasante premiada que tiene
pH neutro, no es cáustica, no es inflamable y es
biodegradable. Al actuar conjuntamente con
nuestros microbios (Ozzy®), estos productos
superiores ayudan a eliminar o a reducir mucho
su necesidad de desechar residuos peligrosos,
con lo que le brindan todo el rendimiento
-habitual para usted- de un limpiador de piezas
típico a base de solventes, sin ninguno de sus
riesgos y complicaciones. Usted ha tomado una
excelente decisión.
Base Diagram, Model SW-37: ............. 10
Ozzy ®
BIOREMEDIATING parts washing system.
®
de l'équipement: ... Intérieur De Couverture Arrière
®
Ozzy ®
SmartWash er
Ozzy ®
®
Manual De Operación
1
Manuel D’utilisation
Installation and Setup: ........................
Operating Manual
Safety Instructions: .... inside front cover
EST sûr et facile à utiliser
UTILISE la dernière technologie de biorestauration
pour éliminer les déchets dangereux du liquide
CONTRIBUE à libérer de la réglementation et à
réduire l'intoxication de votre lieu de travail et à
réduire les paperasses officielles
ÉCONOMISE votre argent
SmartWasher®
Congratulations!
SmartWasher
Change The OzzyMat Every 30 Days To Maintain Cleaning Performance
INSTALLATION AND SETUP
Your SmartWasher® is almost ready to use. (The OzzyMat ®, support grid and
false bottom of the sink are packed inside the sink). Visually inspect for damage
(minor scratches and scuffs are normal due to the molding process).
Remove the false bottom and check to make
sure the mat support grid is in the bottom of the
sink. Remove and discard packing material.
PARTS WASHER SETUP
37 BASKET
MAT SUPPORT GRID
The SmartWasher® will weigh approximately 465 pounds (211 kg) when it is
filled with fluid. It should be installed close enough to a normal 115VAC
(220VAC) ground fault circuit interrupter (GFCI) electrical outlet so that it can
be plugged in. The SmartWasher should be the only item plugged into this
circuit. DO NOT PLUG IN BEFORE ADDING FLUID.
PARTS WASHER OPERATION
1.
The pump switch is attached to a ten minute timer. Turning the
switch ON (upward position) will start fluid flowing for ten
minutes. To restart the flow, turn the switch OFF then ON
again and the flow will restart for another ten minutes.
2.
Adjust the valve at the base of the nozzle to control the flow
of the fluid through the nozzle. The valve at the base of the
brush hose controls the flow of fluid through the brush. Both
outlets can be operated independently or together.
OzzyMat ®
Change the OzzyMat every 30 days or once a
month to maintain cleaning performance.
The OzzyMat traps sludge and dirt as small as 50 microns. It works
effectively even when it appears dirty. At some point, however, it will
become saturated and unable to pass fluid freely and should be changed.
The FL-4 Multi-layer OzzyMat allows you the benefit of being able to peel
layers between mat changes.
OzzyMat FL-4 Maintenance
1. Make sure the pump is not running.
DRAIN BASKET
1. Remove the OzzyMat® from its package, unfold it and lay it
on the mat support grid located in the lowest level in the
sink. Make sure to lay the OzzyMat white side up.
2. Remove the False Bottom from the
sink.
CHANGE THE OZZYMAT
3. Peel away the top layer of the
OzzyMat and wring out any excess
fluid. Then, dispose of this layer
according to your local regulations.
4. Return the False Bottom to its proper
place.
the OzzyMat® needs to
be replaced every 30
days or once a month
to maintain cleaning
performance.
2. Place the false bottom in position in the sink.
3. Form the flexible nozzle to its desired shape and be sure
that the parts brush is inside the sink.
4. DO NOT PLUG UNIT IN BEFORE ADDING
OZZYJUICE.
5. At start up, carefully add 25 gallons ((five) 5-gallon
containers) of OzzyJuice® to the SmartWasher by slowly
pouring the solution directly into the sink.
6. Plug the unit into a 115V (220VAC) GFCI electrical outlet.
ENGLISH
Operating Manual
FALSE BOTTOM
OZZYMAT®
7. The SmartWasher will take approximately four hours to
heat up to its selected optimal temperature of 105°F (+-2°)
(40°C)(+-1°) OR 115° F(+-2°) (46°C)(+-1°). This
temperature will be maintained as long as the
SmartWasher is plugged in and full of OzzyJuice. (If the
Add Fluid Light is on, the heater automatically shuts off.)
REPLACING THE OZZYMAT
Maintain the performance and effectiveness of the
OzzyJuice by changing the OzzyMat EVERY 30 DAYS.
1. Make sure the pump is not running.
2. Remove the False Bottom from the sink.
3. Remove the last layer of the soiled OzzyMat and set to one side
of the filter support grid.
4. Remove a new OzzyMat from its poly bag, unfold the mat and lay
it on top of the filter support grid - white side up.
5. Wring any excess fluid from the old mat onto the new OzzyMat. It
is important to wring used OzzyMat prior to disposal.
6. Take the old, used OzzyMat and place into the poly bag the new
mat came in.
7. Return the False Bottom to its proper position.
8. Discard used OzzyMat in accordance with your local regulations.
CHECK LOCAL REGULATIONS: You may be able to dispose of your used OzzyMat as solid waste or with your other absorbent mats.
1
®
Ozzy ®
SmartWasher
®
INSTALLATION AND SETUP Cont.
Ozzy ®
Operating Manual
®
To maintain the effectiveness and performance of the
OzzyJuice change the OzzyMat once a month.
OZZYJUICE®
TEMPERATURE SETTINGS
Degreasing Solution
The SmartWasher® uses a
specially formulated fluid
which provides a combination of excellent
cleaning characteristics, safety and nutrition for the Ozzy® microbes. OzzyJuice® is
provided in ready-to-use containers.
ADDING OZZYJUICE®
Slowly pour a full container of OzzyJuice
directly into the SmartWasher sink. The
“Add Fluid” light should go out when you
have completed this process.
DO NOT ADD
WATER, SOLVENT, MINERAL SPIRITS,
GASOLINE OR KEROSENE TO YOUR
SMARTWASHER.
Depending on the OzzyJuice solution shipped
with your SmartWasher, the thermostat is
factory-set to maintain fluid temperature
between 105° F to 115° F (+/-2°) (40°C to
46°C)(+/-1°). This temperature provides the
optimum condition for effective cleaning and
activity of Ozzy microbes.
The heater will not operate when the fluid level
becomes critically low. Lift the sink and check
your fluid level. When the “Add Fluid Light”
illuminates add 1 (5) gallon container of
OzzyJuice. If, after a reasonable warm-up
period, the fluid temperature seems too hot or
too cold, please refer to the “Troubleshooting”
section on page 6, 7 and page 8.
If the temperature falls below the recommended minimum, the system will still clean,
but remediation of the hydrocarbons by the
Ozzy microbe colony will slow down. However, the microbes will not die. The Ozzy
colony will become more active when the fluid
temperature reaches the appropriate level.
ENGLISH
To help monitor and maintain the proper
fluid level, the SmartWasher is equipped
with an “Add Fluid Light”. When the “Add
Fluid” light comes on the heater in the
unit will turn off until an ENTIRE (5)
gallon container of OzzyJuice is added.
The “Add Fluid” light will shut off and the
heater will come back on once the (5)
gallon container of OzzyJuice is added to
the SmartWasher.
Your SmartWasher should be plugged in 24
hours a day, 7 days a week to maintain
optimal temperature.
CHANGE THE OZZYMAT
2
SmartWash er
ENGLISH
PROPER USE, CARE & MAINTENANCE
CHANGE THE OZZYMAT
Ozzy ®
Operating Manual
®
Suggested Annual Maintenance:
1.
2.
3.
4.
5.
6.
Pump out the fluid into containers until the machine is
drained.
Unplug the SmartWasher.
Remove the sink from the base. Inspect and
remove any sludge that might have accumulated on
the bottom of the unit.
Clean the base with water to remove any debris.
Visually check the condition of the hoses, connectors,
etc. If everything appears to be in good working
condition, reassemble sink, change OzzyMat, and
return the OzzyJuice to the SmartWasher.
If you fail to maintain your SmartWasher you may
still be able to save your fluid:
Simply perform the annual maintenance described
above and then add OzzyBooster for an extra supply of
microbes to bring your fluid back into conformity. If your
fluid has developed an odor, you may also add Odor
Neutralizer.
3
®
SmartWasher
®
FREQUENTLY ASKED QUESTIONS
Ozzy ®
Operating Manual
®
What is BIOREMEDIATION?
Bioremediation is the use of biological agents such as
microbes or plants to break down or neutralize “hazardous substances” or “contaminants” thereby removing
dangerous chemicals from the environment. The process
of bioremediation is listed as one of the Environmental
Protection Agency’s (EPA) innovative technologies.
How is “Bioremediating” different from “Biodegradable”?
BIOREMEDIATION is the use of natural biological agents
such as microbes to break down or neutralize “hazardous
substances” or “contaminants”. FOR EXAMPLE: In the
SmartWasher, Ozzy(s), natural biological agents or
microbes, break down the carbon-based contaminants
(grease and oil) and turn them into harmless carbon
dioxide and water. BIODEGRADABLE means that a
substance or mixture is subject to or could be broken
down by biological agents into smaller compounds.
Who and what is Ozzy®?
Ozzy is the name we selected for the blend of nonpathogenic (harmless to humans) microbes in the SmartWasher system. Our microbes, Ozzy and his friends, eat
potentially harmful hydrocarbon wastes in the SmartWasher and transform these wastes into very small quantities of carbon dioxide and water. Similar types of
microbes have been used for many years in various bioremediation applications, such as oil spills, including the
Gulf of Mexico spill in 2010, and the Exxon Valdez disaster in 1989.
What happens to the grease, oil and other contaminants
in the SmartWasher?
Grease, oil and other contaminants are bioremediated in
the SmartWasher - transformed into harmless,
non-hazardous by-products such as carbon dioxide and
water. Particulate matter, such as sand, grit, dirt and paint
chips are trapped in the OzzyMat to be disposed of
properly.
How often do I change the fluid (OzzyJuice)?
If you are changing your OzzyMat a minimum of once a
month, under normal use and with proper maintenance,
you should never have to change or haul away used
OzzyJuice. This is one of the biggest advantages of the
SmartWasher system. Ozzy(s) microbes clean contaminants from the fluid through the process of bioremediation.
This leaves you with clean OzzyJuice to work with day after
day.
Why is the SmartWasher heated?
Two reasons: First, it keeps Ozzy eating at an optimal level
to clean the solution as quickly as possible. Secondly,
warm solution simply cleans better than cold solution. An
added benefit to warm solution: it makes it more enjoyable
to work with, especially in winter.
Why doesn’t OzzyJuice damage my hands like solvents?
OzzyJuice is a pH-neutral, non-caustic, water-based
formula that will not dry, crack or irritate the skin. Solvents
are caustic and pull fat cells from the skin, possibly causing
extreme drying, redness, blisters, and other dermatological
problems.
Can I use OzzyJuice in other parts washers?
We do not recommend that OzzyJuice be used in other
parts washers. The OzzyJuice and the SmartWasher were
made to work together with variables such as specific
temperatures, compensation for foam, and so on. Also
remember, the Ozzy(s) microbes are in the OzzyMat and if
the OzzyJuice is used in another machine it will not have
the Ozzy(s) microbes to clean the fluid.
How much oil can I put into the SmartWasher at a time?
As with all parts cleaners, excessive greases, oils and
fluids should be disposed of prior to washing parts. The
SmartWasher can handle large, tough, dirty jobs, but was
not designed to be - nor should be treated as - a waste oil
dump.
ENGLISH
How well does OzzyJuice clean?
OzzyJuice is extraordinarily powerful and cleans
extremely well. OzzyJuice is a surfactant that breaks
down the surface tension between the grease and the
part rather than dissolving it; the grease actually lifts off
the parts leaving behind clean surfaces. Note that while
OzzyJuice cleans differently than dangerous solvents or
mineral spirits, it cleans just as well.
Will OzzyJuice clean carburetors, transmissions,
aluminum, brakes and anything else in my shop?
YES. Not only is OzzyJuice effective on these parts, it will
not damage non-metal components that may be attached
to the parts being cleaned such as rubber or plastic fittings.
As with all parts cleaners, some items are going to become
cleaner at different rates than others due to the degree and
type of grime encountered.
CHANGE THE OZZYMAT
4
SmartWash er
ENGLISH
FREQUENTLY ASKED QUESTIONS
CHANGE THE OZZYMAT
Operating Manual
®
Can I use other fluids in my SmartWasher?
The SmartWasher parts washing system has been painstakingly developed to work effectively as a whole: SmartWasher, OzzyJuice and OzzyMat. Other solutions may
damage the machine or kill Ozzy, thereby eliminating the
advantages of the SmartWasher. The use of other
solutions in the SmartWasher will void the warranty.
Can the SmartWasher overheat if the OzzyJuice gets low?
NO. The heater is automatically de-activated when the
“Add Fluid” indicator light is illuminated. While the pump
will continue to operate, the heater will not be reactivated
until (1) entire 5 gallon box of OzzyJuice is added to the
system and the “Add Fluid” indicator light is off.
Can I simply add water to the SmartWasher to adjust
the fluid level?
NO. Adding water will dilute the OzzyJuice, severely
impacting its performance.
How often do I add OzzyJuice to the SmartWasher?
The SmartWasher comes equipped with an add fluid light
which illuminates when you are low on fluid. When this
light is on simply add (1) 5 gallon container of OzzyJuice to
bring the fluid level up to normal. On average, with normal
use, you will add (1) 5 gallon container of OzzyJuice
approximately every six to eight weeks.
How quickly can Ozzy break down oil and grease?
Once activated, Ozzy and his friends are constantly eating.
Assuming the system is operating optimally (OzzyJuice
temperature between 105°F - 115°F and the OzzyMat
routinely changed a minimum of once every 30 days) the
rate at which the hydrocarbons can remediate can
approach 80% every seven days. Analyses performed on
samples of used OzzyJuice from operating SmartWasher
systems consistently show oil and grease levels in the
1,400 parts per million range. BY COMPARISON, used,
non-bioremediating, aqueous cleaners can average
over 20,000 parts per million of oil and grease.
Does anything kill Ozzy?
YES. Any biocides designed to kill microbes, such as
bleach and Lysol™, will kill Ozzy; chemicals that kill living
things like some strong pesticides and rat poison may be
harmful to Ozzy.
How often do I change the OzzyMat?
At least once a month. This simple act accomplishes three
things: First, it keeps trapped contaminants from reaching
inappropriate levels. Secondly, Ozzy microbes are
introduced into the SmartWasher system through the OzzyMat. Every time you change the OzzyMat you introduce
fresh Ozzy(s) to the existing microbe colony which keeps
the system working at an optimum level. Finally, changing
the OzzyMat keeps sludge from building up in the base of
the unit. If the OzzyMat is not changed regularly and
allowed to become clogged, large contaminants can flow
into the reservoir via the overflow holes in the sink, potentially causing sludge to build up.
How do I dispose of the OzzyMat?
In many areas the OzzyMat can be disposed of in a
non-leaching, sealed manner, and disposed of as solid
waste. But it must always be disposed of in accordance
with the Federal, State and local regulations. More OzzyMat disposal information is located in the Science section
of the ChemFree website, www.chemfree.com.
What do I do if the OzzyMat clogs up quickly with grease?
If you are using the FL-3 Single Layer OzzyMat then you
may want to switch to the FL-4 Multi-Layer OzzyMat. The
FL-4 OzzyMat has 4 layers intended to be peeled away
weekly, which helps eliminate unnecessary clogging. If you
are using the FL-4 OzzyMat then you need to make sure
you are peeling away the individual layers on a weekly
basis. Change the entire OzzyMat on the 4th week OR
every month. Make sure to remove any excess grease,
dirt and debris from dirty parts prior to washing.
Is there a warranty for the SmartWasher?
The SmartWasher is warranted against defects for one
year. For more detailed information on the warranty please
refer to your SmartWasher Operations Manual or visit our
web site, www.chemfree.com and look in the section titled
“Use And Care”.
5
®
Ozzy ®
SmartWasher
®
TROUBLE SHOOTING
Ozzy ®
Operating Manual
®
Cold OzzyJuice
Overheated OzzyJuice
Issue - OVERHEATED FLUID
Issue - COLD FLUID
IF THE SMARTWASHER IS LOW ON FLUID, THE
HEATER AUTOMATICALLY SHUTS OFF.
Check to see if the “Add Fluid” indicators are lit. There
should be approximately 11” (28 cm) of fluid in the
machine when it is low.
If the fluid becomes extremely hot and exceeds
120°F (49°C) unplug the SmartWasher and call
customer service at 1-770-564-5580.
If the “Add Fluid” light is lit, add a full container of
OzzyJuice (the light should go out).
Allow for a reasonable warm up period and then
recheck.
The Thermostat is factory-set to maintain the fluid
at 105° F to 115° F (+-2°) ( 40°C or 46°C (+-1°)).
OzzyJuice Discoloration Or Odor
Spilled OzzyJuice
Issue - FLUID SPILLAGE ONTO FLOOR
OzzyJuice may become dark in color due to dyes in
oils or greases removed from dirty parts. This will not
affect its cleaning power. If the fluid should develop a
strong odor, it may be contaminated and you should
call ChemFree Technical Support for assistance in
diagnosing the problem.
OzzyJuice will cause the floor to become
slippery. Use caution when walking in or near
spilled fluid. To clean up an accidental spill of
new, unused fluid simply soak up the solution
with an absorbent material, (or wash spillage
down the nearest sanitary sewer). If the spilled
OzzyJuice has been used, you must dispose of
the spillage in accordance with local regulations.
If left to dry, the fluid will leave a tacky spot on the
floor that when wet, will again become slippery.
ENGLISH
Issue - FLUID DISCOLORATION OR ODOR
CHANGE THE OZZYMAT
6
SmartWash er
ENGLISH
TROUBLE SHOOTING
Ozzy ®
Operating Manual
CHANGE THE OZZYMAT
®
If excessive oil is dumped into the SmartWasher, take the
following steps to remedy the situation;
Issue - EXCESSIVE OIL
DUMPED IN SYSTEM
1.
Unplug the SmartWasher and lift the sink off the base.
2.
Skim excessive oil off the top of the OzzyJuice or place an
absorbent pad on top of the fluid, soak up the oil and
dispose of it in accordance with local regulations.
3.
In extreme cases, it may be necessary to replace all of the
OzzyJuice in the SmartWasher. Dispose of contaminated
OzzyJuice and OzzyMats according to local regulations.
4.
If you replace all of the OzzyJuice, rinse the base of the
SmartWasher to remove all excess oil and dirt.
5.
Once unit has been cleaned, replace the sink and add a
new OzzyMat and 25 gallons ((5) 5-gallon containers) of
new OzzyJuice.
Issue - EXCESSIVE FLUID LOSS:
With “normal usage” you should have to add a five
gallon container of OzzyJuice approximately every 6 to
8 weeks. “Normal usage” means the equivalent of
several users in a 10 hour day in a standard
maintenance, repair and operation facility or several
users in a multiple bay garage facility.
CHECKING for Problems:
Issue - EXCESSIVE FLUID LOSS:
a.
Check the fluid temperature, If the temperature is above
120°F (49°C) the probe is not working properly.
Temperatures above 120°F (49°C) will increase the rate of
evaporation.
b.
Examine closely where the sink and base meet. Are there
any gaps? Is the base bowed? Is the sink warped? The
SmartWasher operates as a closed system; any gaps will
provide space for air to enter and condensation to escape.
c.
Is the SmartWasher “leaking”? Where is it “leaking” from?
Make sure the nozzle and brush are flowing into the sink.
If the fluid is leaking from the body of the base? The base
will need to be replaced.
d.
If none of the previous apply, this rules out any problem
with the SmartWasher itself. Make sure you and your
coworkers are aware that certain practices can cause you
to use excessive amounts of OzzyJuice.
7
®
SmartWasher
®
TROUBLE SHOOTING
Ozzy ®
Operating Manual
®
ISSUE - Low or No Fluid from Brush/Nozzle
Check the following:
Make sure that the valves at the base of the nozzle and brush are open. If a stronger flow
through either device is needed, turn the valve on the unused tool to the closed position.
Hoses from the pump to the nozzle and brush could be clogged, pinched or disconnected.
Check the hoses from the pump to the nozzle making sure they are in working order.
Make sure SmartWasher is not low on fluid.
Hose connections should be secure and not leaking.
The pump comes with a one year factory warranty. If the pump is faulty, call your local distributor or ChemFree Technical Support to order your warranty replacement. Have the serial
number of the SmartWasher unit available when calling.
CHECKING Practices:
How often, how much and when are you adding fluid? A full container of OzzyJuice should
be added immediately when the “Add Fluid Light” comes on. The system is designed to warn
users at the point at which fluid should be added. Please keep in mind that the light will remain
illuminated while fluid is low, and more fluid will be needed to reach the proper operating level.
When did you notice the change in usage? If fluid usage has been fine for a period of time
and usage has just recently increased, check to see if anything has changed recently. (New
employees, more employees, more parts being cleaned, longer hours of use, etc.)
How many hours a day do you have the pump running? The more the pump runs, the
more evaporation occurs. Never leave the pump running when the SmartWasher is not in use.
How many operators and how many hours a day are you using the SmartWasher? This
will help you determine if they have high, normal or low usage. If you have higher than normal
usage, you will have higher fluid usage.
Does the OzzyMat clog up and cause the fluid to pool up in the sink? If the fluid is
backing up in the sink and not draining through the OzzyMat properly, there will be increased
evaporation and the low fluid light may come on prematurely because the fluid is in the sink,
not in the base.
Are operators squeezing the excessive fluid out of the OzzyMat into the sink after
installing a new OzzyMat? When changing out the old OzzyMat, squeeze out any excessive
fluid.
CONTACT CUSTOMER SERVICE
770-564-5580 (P)
770-564-5533 (F)
800-521-7182
ChemFree Corporation 8 Meca Way, Norcross, GA 30093 U.S.A.
ENGLISH
www.chemfree.com
CHANGE THE OZZYMAT
8
SmartWash er
Front View
1530-BASKT
Plastic Basket
1032-FABOT-37
False Bottom
FL-4 OzzyMat
Multi-Layer OzzyMat
4550-NOZKT-SS
SuperSink Nozzle Kit
1410-MSGRD-PL
Mat Support Grid
1630-FELBO-12
1605-CLAMP
Elbow 1/2” F Black
1/2” Clamp
1555-VELST
1608-BVALV-12
Velcro Strap
1/2” Ball Valve
1607-GMVAL-12
Valve Male Barb 1/2” Male NPT
4538-ABRSY-4
Angled Brush Asy w/ 4-ft hose
1400-DBSKT
Drain Basket
Rear View
4425-SKPMP-37
SW-37 Sink To Pump Kit
1490-QCINS-12
Quick Connect 1/2 insert Coupling
MX Hose Barb
9
®
Operating Manual
ENGLISH
SW-37 Sink Diagram
Ozzy ®
SmartWasher
®
SW-37 BASE DIAGRAM
Ozzy ®
Operating Manual
FRONT VIEW
Hose
SIDE VIEW
Pump
Pump
4100-CONTR-37
Control Assembly 37 110v
INCLUDES: pass thru,
support bracket, control box
assembly, heater assembly,
probe, pump assembly, and hose kit
Power Cord
Heater
Probe
Heater
4467-PMPHK-37
4160-CDSKT-110
Power Cord Kit
INCLUDES: cord, strain relief
connector, and o-ring
Pump Hose Kit for 37
INCLUDES: black
insta-grip tubing, pinch
clamp, adjustable clamp,
and (F) quick connect
Control Box
4138-CBASY-37
Control Box Assembly
5-LED for 37
INCLUDES: control box, toggle switch
and boot, fuse, and strain relief connector
adjustable clamp
4470-PMASY-37
Pump Assembly for 37 110v
INCLUDES: pump, coupling, liquid tight fittings, straight tubing
4050-HTASY-110
Heater Assembly for 37 110v
INCLUDES: heater, strain relief connectors, and o-rings
4470-PMASY-37
Pump Assembly for 37 110v
(pump, coupling, liquid tight fittings,
straight tubing)
Pump
4050-HTASY-110
1270-PROBE-37
Probe for 37
Probe
(heater, strain relief connectors, and o-rings)
Heater
FRONT AND SIDE VIEW
Control Assembly 37
ENGLISH
10
SmartWash er
4100-CONTR-37
Control Assembly 37 110v
INCLUDES: pass thru, support bracket, control box assembly,
power cord, heater assembly, probe, pump assembly, and hose kit
11
®
Operating Manual
4138-CBASY-37
Control Box Assembly 5-LED for 37
INCLUDES: control box, toggle switch and boot, fuse,
and strain relief connector
Probe and Pump
Front View
1270-PROBE-37
Probe for 37
4050-HTASY-110
INCLUDES: heater, strain relief connectors, and o-rings
4470-PMASY-37
Pump Assembly 110v for 37
INCLUDES: pump, connectors, and tubing
ENGLISH
SW-37 Replacement Parts
Ozzy ®
SmartWasher
®
My SmartWasher® Records
Ozzy ®
Operating Manual
English
OzzyJuice® Solution Part Number:________________
OzzyMat™ Part Number:___________________________
Serial Number:____________________________________
Distributor Name:___________________________________
Sales Rep Name:__________________________________
Sales Rep Contact Phone:____________________________
1-770-564-5580
ChemFree Technical Website Address:______________ www.chemfree.com
ChemFree Technical Support Number:___________
Francais
Nombre Modèle:___________________________________
Le Nombre de Partie de Solution d'OzzyJuice®:___
Le Nombre de Partie d'OzzyMat:__________________
Numéro de Série:__________________________________
Nom de Distributeur:______________________________
Nom de Représentant:__________________________________
Le Téléphone de Contact de Représentant:______
ChemFree le Nombre de Soutien Technique:________
ChemFree l'Adresse de site internet Technique:___
001-770-564-5580
www.chemfree.com
Espanol
Número de Modelo:__________________________________
Número de parte de la solución de OzzyJuice®:___
Número de parte del OzzyMat™:____________________
Número de serie:____________________________________
Nombre del distribuidor:____________________________
Nombre del representante de ventas:______________
Número telefónico del representante de ventas:___
Número telefónico del apoyo técnico ChemFree:__
Dirección web del servicio técnico ChemFree:____
001-770-564-5580
www.chemfree.com
Model Number:_____________________________________
SmartWash er
®
Operating Manual
CHANGE YOUR OZZYMAT™ EVERY MONTH:
January
February
March
April
May
June
July
August
September
October
November
December
English
Place an X through the appropriate month to indicate the mat has been changed.
CHANGER VOTRE OZZYMAT™ CHAQUE MOIS:
Janvier
Février
Mars
Avril
Pouvoir
Juin
Juillet
Août
Septembre
Octobre
Novembre
Décembre
Francais
Placer un X par le mois approprié pour indiquer que le tapis a été changé.
CAMBIE SU OZZYMAT™ TODOS LOS MESES:
Enero
Febrero
Marzo
Abril
Mayo
Junio
Julio
Agosto
Septiembre
Octubre
Noviembre
Diciembre
Espanol
Change OzzyMat CALENDAR
Ozzy ®
Coloque una X en el mes apropiado para indicar que el OzzyMat ha sido cambiado
SmartWash er
DISCLAIMER AND EQUIPMENT WARRANTY
®
Ozzy ®
Operating Manual
Déni de Responsabilité
Exención de
Responsabilidad
The SmartWasher® is designed exclusively for
removing oil and grease from automotive and
industrial parts, and then remediating the
residue. Any other use of this system, such as
dumping waste oil, is not recommended and
will cause damage to the system.
Le SmartWasher® est conçu exclusivement
pour retirer la graisse et l'huile des pièces
automobiles et industrielles, puis de
biorestaurer les résidus. Toute autre utilisation
de ce système, comme la décharge d'huiles
usées, n'est pas recommandée et pourrait
endommager le système.
El
SmartWasher®
está
diseñado
exclusivamente para eliminar el aceite y la
grasa de piezas automotrices e industriales,
y luego corregir el residuo. Todo otro uso de
este sistema, como el vertido de aceite
residual, no se recomienda y causará daños
al sistema.
ChemFree® Corporation cannot be responsible for any damages resulting from
improper, inappropriate or unauthorized use.
ChemFree® Corporation ne peut pas être tenu
pour responsable des dommages quels qu'ils
soient, résultant d'une utilisation incorrecte,
inappropriée ou non autorisée.
Corporation
no
puede
ChemFree®
responsabilizarse por ningún daño que
resulte del uso incorrecto, inapropiado o no
autorizado.
In Addition
De Plus
Además
While ChemFree® Corp. has performed
multiple analyses of used OzzyMats™ and
fluid and found them to be nonhazardous, we
strongly recommend that local regulations
regarding hazardous waste disposal and
handling be consulted before disposing or
handling used ChemFree® products.
Bien que ChemFree® Corp. ait effectué de
nombreuses analyses sur des OzzyMat™ et du
fluide utilisés, et les ait trouvés sans danger,
nous recommandons fortement que les
réglementations locales relatives à la mise au
rebut et à la manutention des déchets
dangereux soit consultée avant de traiter des
produits de ChemFree® qui ont servi.
Si bien ChemFree® Corp. ha realizado
múltiples análisis de OzzyMats™ y fluido
usados y ha hallado que no son peligrosos,
recomendamos muy especialmente consultar las regulaciones locales relativas a la
eliminación y manejo de residuos peligrosos
antes de eliminar o manejar productos
usados de ChemFree®.
ChemFree® Corporation accepts no
responsibility or liability for users’
failure to comply with local
regulations.
ChemFree® Corporation n'accepte ni
responsabilité, ni obligation en cas de
non-respect par les utilisateurs des
réglementations locales.
ChemFree® Corporation no acepta
responsabilidad ni obligación por la
falta de cumplimiento de las regulaciones locales por parte del usuario.
WARRANTY
GARANTIE
GARANTÍA
ChemFree® Corporation will replace, at no
charge to the original purchaser (end user),
any part or parts found to be defective in
material or workmanship, when part is
returned to our factory within 12 (twelve)
months
from
date
of
purchase.
Transportation charges to be paid by
purchaser.
ChemFree® Corporation remplacera, sans
frais pour l'acheteur d'origine (utilisateur
final),
toutes
les
pièces
trouvées
défectueuses pour cause de matériaux ou de
main-d'œuvre, quand ces pièces sont
retournées à notre usine dans les 12 (douze)
mois suivant la date de l'achat. Les frais de
port seront à la charge de l'acheteur.
ChemFree® Corporation reemplazará sin
cargo al comprador original (usuario final)
toda pieza o piezas que se compruebe(n)
con defectos de material o mano de obra, si
la(s) pieza(s) se devuelve(n) a nuestra
fábrica dentro de los 12 (doce) meses desde
la fecha de la compra. Los cargos de
transporte serán pagados por el comprador.
Disclaimer
In the event of any modification to unit,
misuse, negligence, or accident, or the use in
the SmartWasher® system of fluids or filters
other than those specifically authorized by
ChemFree® Corporation, the warranty is void.
There is no other warranty expressed or
implied. The manufacturer shall in no event
be liable for consequential damages.
The manufacturer reserves the right to make
changes in design or improvements to its
product without imposing any obligation on
itself to install the same on its product
previously sold.
Dans l'éventualité d'une quelconque modification de l'unité, de mésusage, de négligence
ou d'accident, ou de l'utilisation dans le
système SmartWasher® des fluides ou de
filtres autres que ceux spécifiquement autorisés par ChemFree® Corporation, cette garantie est annulée.
Il n'existe pas d'autre garantie, explicite ou
implicite. Le constructeur ne doit en aucun
cas est responsable pour des dommages
annexes.
Le constructeur se réserve le droit d'effectuer
des modifications de conception ou des
améliorations sur ses produits, sans
s'imposer d'obligation de les répercuter sur
des produits qu'il a précédemment vendus.
vendus.
En caso de cualquier modificación de la
unidad, mal uso, negligencia o accidente, o
el uso en el sistema SmartWasher® de fluidos
o filtros distintos de los autorizados
específicamente por ChemFree® Cororpation
la garantía se anula.
No existe otra garantía, ni expresa ni
implícita. El fabricante no será responsable
en ningún caso por daños consiguientes.
El fabricante se reserva el derecho de hacer
cambios en el diseño o mejoras a su
producto sin imponerse a sí mismo ninguna
obligación de instalar lo mismo en su
producto vendido previamente.
right time. right choice.
SmartWash er
®
Ozzy ®
Operating Manual
8 Meca Way
Norcross, GA 30093
770-564-5580
www.chemfree.com
Printed On Recycled Paper
the sustainable solution
Copyright © 2014 ChemFree Corporation. All Rights Reserved. ChemFree, SmartWasher, OzzyMat, Ozzy, OzzyJuice, and the Ozzy design are registered trademarks and/or trademarks of ChemFree Corporation. Patent numbers: US 5,961,733; 6,044,854;
6,074,491; 6,019,110; 6,095,163; 6,451,125; 6,374,835; 6,328,045; 6,318,387; 6,440,226; 6,571,810; EP0784518; AT E219704; DE 29522341.3; CA 2,201,314; MX 214799; AU 709648; BR PI9509114-9; CN ZL95196499.2; KOREA 0362009; RU 2172651

Operating Manual

Transcripción

Documentos relacionados

ficha técnica