solidrock - Bridgepoint Systems
Transcripción
solidrock - Bridgepoint Systems
SOLIDROCK PREMIUM STONE & GROUT SEALER Water Based Sealer Repels Oil & Water Based Spills While Resisting Soil & Stains SOLIDROCK Waterbased sealer which lets water vapor out but slows down the penetration of liquid. Outstanding on Stone, Grout and other porous tile. Product of: RTU ph - 8.0 Contents: One U.S. Gallon (3.79 Litres) Cleaning is necessary Surface must be cleaned and thoroughly rinsed. The drier the stone and grout, the better the penetration. Make sure that there are no puddles in grout lines and use air movers to speed the drying of the stone and grout lines before application. If pH of surface is higher than 11, (unusual if thoroughly rinsed), then sealer may not bond properly. Stone & grout lines may need to be rinsed with Spinergy Vivid Neutral Stone Cleaner/Rinse to lower pH of grout before applying sealer. Dilution Instructions Do not dilute. The product is ready to use. Coverage should be between 300 and 1200 sq. ft. per gallon depending on the porosity of the surfaces and the coverage required (grout only or entire surface). Application Methods Grout Application Spray grout lines with pump up sprayer. Squeegee excess into untreated areas and bonnet off non-porous tiles. When dry (typically 1 to 2 hours) if there is a white haze on tiles, then buff off with white polishing pad and 175 rpm rotary machine. Stone Application For entire floor application, spray on sealer then spread with a brush with synthetic fibers. An alternative and sometimes preferred application method is to liberally apply an even coat using a paint pad, roller or brush. Allow sealer to penetrate the surface for 15–30 Post Application Precautions Floor is typically walkable in 3 to 4 hours, ready for use after 8 to 12 hours, and completely cured in 24 hours. These times will be shorter if only grout was sealed. After 6 to 18 months, reapplication may be necessary, depending upon the traffic level, maintenance procedures and the type of surface sealed. CONTAINS Water (CAS# 7732-18-5), Proprietary C6 fluorochemical resin, Isopropyl Alcohol (CAS# 67-63-0) INSTRUCCIONES PARA SU USO Antes de usarse agitese bien la botella. Haga una prueba preliminar de la compatibilidad del producto, en un area poco visible, especial para pulir el marmol y extremadas superficies porosas . Asegurese que el area esta ventilada durante la aplicacion y hasta que se seque . mantenga a los ninos y mascotas fuera del area .El sellador se puede aplicar una hora despues de que toda el agua ha sido removida. Temperatura de la superficie debe estar entre 50 y 80 grados F. Limpieza es necesaria : La superficie debe estar limpia. Entre mas limpia y seca este el area mejores resultados tendra . Asegurese que las lineas del grout esten limpias y use aire para secar mas rapido el area antes de la aplicacion del producto. Ysi el ph de la superficie es mas de 11, entonces el sellador no va a funcionar apropiadamente. El piso talvez deba ser limpiado con Spenergy Vivid Neutral Stone Cleaner/ Rinse para bajar el ph del piso antes de aplicar este producto. Instrucciones de dilucion No se diluya .El producto esta listo para usarse .La botella alcanza a cubrir un area de 300 a 1200 sq. ft por un galon dependiendo de que tan brilloso quiera .(solo grout y superficies de piedra) Metodos de aplicacion Aplicacion en grout: Use un rociador de bomba para aplicarlo en las lineas de grout . Seque el exceso con un trapo. Se seca en 1 a 2 horas y si quedo algo blanco en el azulejo , entonces tiene que pulir con una maquina rotatoria de 175 rpm. Aplicacion en piedra: Para todo el piso ,rocie el sellador y use un cepillo de fibra sintetica para expander el sellador.Tambien puede usar un rodillo ,o una brocha de pintar. Permita que el sellador penetre en la superficie por 15 a 30 minutos. Durante este tiempo, distribuya el sellador sobre toda el area para asegurar una penetracion pareja . Remueva el exceso de sellador con una toalla limpia .Talvez necesite una segunda aplicacion despues de 1 hora .Ponga unas gotas de agua sobre el Nuevo sellador en el piso y vea si loabsorbe si es asi entonces debe aplicarse una segunda vez. IMPORTANT NOTICE TO PURCHASER: Seller’s and manufacturer’s liability for any and all losses or damages resulting from any cause whatsoever shall in no event exceed the purchase price of this product, with respect to which losses or damages are claimed. Before using, the user shall determine the suitability of this product for its intended use, and user assumes all risk and liability whatsoever in connection therewith. Go to www.bridgepoint.com/sds for additional safety, regulatory and liability information. SOLIDROCK May cause skin and eye irritation. Avoid contact with skin and eyes. In case of contact, immediately flush with plenty of water, seek medical advice if irritation persists. Susceptible d’irriter la peau et les yeux. Évitez tout contact avec la peau et les yeux. S’il y a contact, lavez-vous immédiament à la grande eau. Consultez un médicin si l’irritation se fait persistante. SEE SAFETY DATA SHEET VOIR LA FICHE SIGNATÉTIQUE WARNING! Keep out of reach of children. HAZARD STATEMENTS: Causes eye irritation. PRECAUTIONARY STATEMENTS: IF IN EYES: Rinse cautiously with water for several minutes. Remove Contact Lenses, if present and easy to do. Continue rinsing. IF ON SKIN: Wash with plenty of soap and water. IF SKIN irritation occurs: Get medical advice/ attention. ADVERTENCIA! Mantener fuera del alcance de los niños. INDICACIONES DE PELIGRO: Causa irritación al ojo. DECLARACIONES DE PRECAUCIÓN: Si en los ojos: Enjuagarse cuidadosamente con agua por varios minutos. Remueva lentes de contacto si los está usando. Continúe enjugándose. Si en la piel: Lavarse con amplio jabón y agua. Si irritación a la piel ocurre: Obtenga consejo/ atención médica. See Safety Data Sheet (SDS): www.bridgepoint.com/sds for additional safety and regulatory information. Another fine product from Bridgepoint Systems 4282 South 590 West, Salt Lake City, UT 84123 www.bridgepoint.com FLAMMABILITY 1 HEALTH 1 0 REACTIVITY CST20GL DIRECTIONS FOR USE: Before Application SHAKE THOROUGHLY BEFORE EACH USE! Test for suitability in an inconspicuous area, especially for polished marble and extremely porous surfaces. Ensure that the area is well-ventilated during application and until the surface is dry. Keep children and pets out of the area until foot traffic resumes. Sealer may be applied to damp surfaces one hour after standing water has been removed. Surface temperature should be between 50°F and 80°F. Mask any surfaces not intended to be treated. minutes. During this time, distribute sealer over entire area to ensure even penetration. Remove excess sealer by wiping entire surface thoroughly with clean, dry towels. A second coat may be necessary after 1 hour. Place drop of water on newly sealed grout or stone and see if it absorbs into grout or stone. If it does absorb readily, then a second coat is necessary. *CST20GL* • Bonding and protection technology that provides maximumprotection against spots and spills • Protects without affecting slip resistance • Preserves the natural look of stone and can be applied to interior and exterior surfaces • Ideal water based sealer formarble, granite, limestone, saltillo, travertine, sandstone, and terrazzo
Documentos relacionados
stoneperfect - Bridgepoint Systems
May cause skin and eye irritation. Avoid contact with skin and eyes. In case of contact, immediately flush with plenty of water, seek medical advice if irritation persists. Susceptible d’irriter la...
Más detalles