Intellex® Digital Video Management System
Transcripción
Intellex® Digital Video Management System
Intellex® Digital Video Management System Intellex Version 2.1 to 2.1L Feature Upgrade Instructions English, Français, Español, Deutsch Intellex® Digital Video Management System 2 Notice The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice. Copyright Under copyright laws, the contents of this manual may not be copied, photocopied, reproduced, translated or reduced to any electronic medium or machine-readable form, in whole or in part, without prior written consent of Sensormatic Electronics Corporation. © Copyright 2001 Trademarks Sensormatic Electronics Corporation Video Systems Division 6795 Flanders Drive San Diego, CA 92121-2903 U.S.A. Intellex ® is a registered trademark and IntelleCord ™ and SmartSearch ™ are trademarks of Sensormatic Electronics Corporation. Windows® is a registered trademark of Microsoft Corporation. Trademarked names are used throughout this manual. Rather than place a symbol at each occurrence, trademarked names are designated with initial capitalization. Inclusion or exclusion is not a judgment on the validity or legal status of the term. Intellex Version 2.1 to 2.1L Feature Upgrade Instructions 3 Intellex 2.1 to 2.1L Feature Upgrade NOTE: Selecting a new feature level without entering a new Software License Key will render the unit nonfunctional. If this happens, rerun the License Editor and select the correct feature level for the Software License Key installed. NOTE: Installers should make note of any upgrades or repairs performed or new equipment installed in the unit on the Service Record and attach it to the inside of the case. New or replacement Service Records are available from your dealer or from Sensormatic (part no. 2402-1587-01 A). INTELLEX 2.1 TO 2.1L FEATURE UPGRADE Installation Instructions To obtain the Software License Key, complete the Software License Registration Form (part no. 8200-0012-00 A) and fax it to the number indicated on the form. The information on the form must be complete and accurate or else the key could be delayed or wrong. Some of the information is obtained from the Intellex that will be upgraded: Obtain the Intellex information: 1. From the main Intellex screen, click on Utility, then click on About Intellex. The software Version must be 2.10.xx. Click on System. After a few seconds a window will display with the MAC Address. Record the 12-digit MAC Address onto the Software License Registration Form. Click on OK and Close to return to the main screen. NOTE: If the Version is not 2.10.xx, you cannot use this procedure to upgrade the software. Contact your local Sensormatic representative. English Intellex 2.1 limits access to the Live Remote capability (when used with Network Client 2.0) through a combination of feature level selection and Software License Key. It is possible to upgrade an Intellex 2.1 system at the Base feature level to the Live Display feature level by entering a new Software License Key and selecting the new feature level in the License Editor. Intellex® Digital Video Management System 4 2. Record the Intellex serial number onto the Software License Registration Form. The Intellex serial number can be found on the product label on the bottom of the Intellex, or, on newer units, on a label inside the door covering the floppy drive. 3. Record the rest of the required information on the Software License Registration Form. The product code for this upgrade is RDVUPG21LA. The Sensormatic Sales Order is obtained from Customer Service when you place the order for this upgrade. 4. Fax the completed Software License Registration Form to the number indicated in the form. 5. When you receive the form back from Sensormatic, the new Software License Key will be recorded on it. Enter the new License Key and Feature Level: NOTE: Exiting to the system is a protected feature. You must have the EXIT TO SYSTEM privilege to access it (see Security Setup in the Intellex Installation Instructions). 6. From the main screen click on Utility, then Exit. A confirmation screen will ask “Do you wish to quit the program?” Click on Yes. 7. Enter the Exit PIN code on the keypad and click on OK. 8. From the Windows Desktop, double click on the License Editor icon. The License Editor window will be displayed. 9. Verify that the MAC Address displayed in the License Editor window is the same as the one recorded on the Software License Registration Form. If it is not the same, click on Cancel and go to step 14. Then contact your Sensormatic representative. NOTE: The MAC Address is 12 digits long and consists of numbers from 0 to 9 and letters from a to f. Each Intellex unit has a unique MAC Address. If only 11 digits are visible in the MAC Address window, move the mouse cursor into the window and click. Then hold the left mouse button down and slide the cursor left and right to view all 12 characters. Intellex Version 2.1 to 2.1L Feature Upgrade Instructions 5 10. In the Feature Level window, click on the arrow button and select the Live Display feature. 11. Record the License Key information that is displayed in the four windows. You will need this to restore the system to the current state. 12. Starting in the left window, click in each of the four windows for the License Key and backspace to remove the current value. Then type in the Software License Key that is written on the Software License Registration Form. NOTE: The license key consists of 16 characters consisting of the numbers 0-9 and letters a-f. Type in the letters as lower case (not CAPITALS). There are no spaces, dashes, or punctuation marks. 13. Verify the information is entered correctly and click on OK. 14. Double-click on the Intellex icon to start the Intellex software. NOTE: If Intellex does not run, there must be an error in the license key. Repeat step 8, then enter the original license key and select the original feature level, then perform steps 12 and 13. Contact your Sensormatic representative. Your Intellex is now upgraded to Live Remote Display. Système de Gestion Vidéo-numérique d’Intellex® 6 Avis Les informations contenues dans ce manuel étaient actuelles lors de la publication. Le fabricant se réserve le droit de modifier et d’améliorer ses produits. Toutes les spécifications sont de ce fait sujettes à modification sans préavis. Droits d’auteur Conformément à la législation en matière de droits d’auteurs (copyright), le contenu de ce manuel ne peut pas être copié, photocopié, reproduit, traduit ou réduit à aucun support d’information électronique ou mécanique, en tout ou partie, sans l’accord préalable écrit de Sensormatic Electronics Corporation. © Copyright 2001 Marques Sensormatic Electronics Corporation Video Systems Division 6795 Flanders Drive San Diego, CA 92121-2903 U.S.A. Intellex® est une marque déposée et IntelleCord™ et Smart Search™ sont marques commerciales de Sensormatic Electronics Corporation. Windows® est une marque déposée de Microsoft Corporation. Des noms de marques sont utilisés dans tout ce manuel. Au lieu de mettre un symbole à chacune de leurs apparitions, on a désigné les noms de marques par une majuscule initiale. L’inclusion ou l’exclusion ne constitue pas une opinion sur la validité ou le statut juridique du terme. Instructions de mise à niveau de la Version 2.1 à 2.1L 7 Mise à niveau d’Intellex 2.1 à 2.1L L’unité Intellex 2.1 limite l’accès à la fonction de vidéo en direct (en cas d’utilisation de Network Client 2.0) par la sélection du niveau de fonctionnalité et la mise en œuvre d’une clé de protection logicielle. Il est possible de migrer d’un système Intellex 2.1 doté du niveau de fonctionnalité de base vers le niveau d’affichage en direct en entrant une nouvelle clé de protection et en sélectionnant le niveau de fonctionnalité approprié dans l’Éditeur de licence. REMARQUE : Les installateurs doivent consigner toute mise à niveau, réparation ou installation de nouvel équipement dans l’unité sur la Fiche de maintenance et ranger celle-ci à l’intérieur du boîtier. Vous pouvez vous procurer des Fiches de maintenance supplémentaires auprès de votre distributeur ou de Sensormatic (n° de pièce 2402-1587-01 A). MISE À NIVEAU D’INTELLEX 2.1 À 2.1L Instructions d’installation Pour obtenir une clé de protection logicielle, veuillez compléter le formulaire de demande ad hoc (n° de pièce 8200-0012-04 A) et le faxer au numéro indiqué. Les informations communiquées dans ce formulaire doivent être complètes et précises, sans quoi la clé risquerait d’être mal configurée ou son envoi retardé. Certaines informations se rapportent à l’unité Intellex mise à niveau : Complétez les informations relatives à l’unité Intellex : 1. Dans l’écran Intellex principal, cliquez sur Utilitaire, puis sur À propos d’Intellex. Le numéro de version du logiciel doit être 2.10.xx. Cliquez sur Système. Au bout de quelques secondes, une fenêtre contenant l’adresse MAC s’affiche. Recopiez l’adresse MAC de 12 caractères sur le formulaire de demande. Cliquez sur OK et Fermer pour revenir à l’écran principal. Français REMARQUE : La sélection d’un nouveau niveau de fonctionnalité sans définition d’une nouvelle clé de protection rend l’unité inopérationnelle. Il convient dans ce cas de réexécuter l’Éditeur de licence et de sélectionner le niveau de fonctionnalité correspondant à la clé de protection installée. Système de Gestion Vidéo-numérique d’Intellex® 8 REMARQUE : Si le numéro de version n’est pas 2.10.xx, vous ne pouvez appliquer cette procédure pour mettre le logiciel à niveau. Contactez votre représentant Sensormatic. 2. Inscrivez le numéro de série de l’unité Intellex sur le formulaire de demande. Celui-ci se trouve sur l’étiquette apposée sous l’unité Intellex ou, sur les nouveaux modèles, à l’intérieur du couvercle du lecteur de disquettes. 3. Complétez les autres informations demandées sur le formulaire. Le code produit de cette mise à niveau est RDVUPG21LA. Le bordereau de vente Sensormatic vous est envoyé par le Service clientèle lorsque vous commandez la présente mise à niveau. 4. Faxez le formulaire de demande au numéro indiqué. 5. Sensormatic vous le renverra complété de la nouvelle clé de protection logicielle. Entrez la nouvelle clé de protection et le niveau de fonctionnalité : REMARQUE : Revenir au système est une fonction protégée. Vous devez disposer du privilège de SORTIE VERS LE SYSTÈME pour y accéder (reportez-vous à la section Réglage de la sécurité dans les Instructions d’installation d’Intellex). 6. Dans l’écran principal, cliquez sur Utilitaire, puis sur Quitter. Un écran de confirmation s’affiche avec le message «Souhaitez-vous quitter le programme ?». Cliquez sur Oui. 7. Composez le code d’identification de sortie sur le pavé numérique et cliquez sur OK. 8. Sur le bureau de Windows, double-cliquez sur l’icône Éditeur de licence. La fenêtre Éditeur de licence s’affiche. 9. Assurez-vous que l’adresse MAC affichée dans la fenêtre Éditeur de licence est identique à celle figurant sur le formulaire de demande. Si tel n’est pas le cas, cliquez sur Annuler et passez à l’étape 14. Contactez votre représentant Sensormatic. Instructions de mise à niveau de la Version 2.1 à 2.1L 9 REMARQUE : L’adresse MAC comporte 12 caractères constitués de chiffres compris entre 0 et 9 et de lettres de a à f. Chaque unité Intellex possède une adresse MAC unique. Si la fenêtre Adresse MAC n’affiche que 11 caractères, amenez le curseur de la souris dans la fenêtre et cliquez. Ensuite, maintenez le bouton gauche de la souris enfoncé tout en déplaçant le curseur de gauche à droite pour visualiser les 12 caractères. 10. Dans la fenêtre Feature Level, cliquez sur le bouton fléché et sélectionnez Live Display. 11. Prenez note des informations relatives à la clé de protection affichées dans les quatre fenêtres. Vous en aurez besoin pour rétablir le système dans son état actuel. 12. En commençant par la fenêtre de gauche, cliquez sur chacune des fenêtres se rapportant à la clé de protection et appuyez sur la touche Retour arrière pour effacer la valeur existante. Ensuite, tapez le numéro de la clé de protection logicielle figurant sur le formulaire de demande. REMARQUE : La clé de protection comporte 16 caractères constitués de chiffres compris entre 0 et 9 et de lettres de a à f . Utilisez des minuscules (pas de MAJUSCULES). Ne tapez aucun espace, tiret ou signe de ponctuation. 13. Vérifiez que les informations saisies sont correctes et cliquez sur OK. 14. Double-cliquez sur l’icône Intellex pour démarrer le logiciel Intellex. REMARQUE : Si le logiciel Intellex ne s’exécute pas, c’est probablement que vous avez commis une erreur en tapant la clé de protection. Recommencez l’étape 8, entrez la clé de protection et le niveau de fonctionnalité d’origine, puis effectuez les étapes 12 et 13. Contactez votre représentant Sensormatic. La mise à niveau de votre unité Intellex vers l’affichage direct à distance est à présent terminée. Intellex® Sistema de Administración de Vídeo Digital 10 Aviso La información contenida en este manual corresponde al estado del producto en el momento de su publicación. El fabricante se reserva el derecho a revisar y mejorar sus productos. Por lo tanto, todas las especificaciones están sujetas a cambios sin previa notificación. Copyright De acuerdo con las leyes de derechos de autor, el contenido de este manual no puede copiarse, fotocopiarse, reproducirse, traducirse ni convertirse, ya sea parcial o totalmente, a ningún formato electrónico o soporte legible por cualquier medio mecánico, sin la previa autorización por escrito de Sensormatic Electronics Corporation. © Copyright 2001 Marcas comerciales Sensormatic Electronics Corporation Video Systems Division 6795 Flanders Drive San Diego, CA 92121-2903 EE.UU. Intellex® es una marca comercial registrada e IntelleCord™ y Smart Search ™ son marcas comerciales de Sensormatic Electronics Corporation. Windows® es una marca registrada de Microsoft Corporation. Los nombres comerciales se utilizan en todo este manual. En lugar de resaltarlos con el símbolo correspondiente cada vez que se mencionan, los nombres comerciales se distinguen mediante letras iniciales mayúsculas. La inclusión o exclusión no representa un juicio sobre la validez o estado legal del término. Instrucciones para la actualización de la versión 2.1 de Intellex a la 2.1L 11 Actualización de Intellex 2.1 a 2.1L Intellex 2.1 limita el acceso a la característica de actualización remota “Live Remote” (cuando se utiliza con Network Client 2.0) mediante una combinación de selección del nivel de características y una clave de licencia de software. Un sistema Intellex 2.1 con nivel funcional Básico se puede actualizar al nivel de visualización en directo (“Live Display”) introduciendo una nueva clave de licencia de software y seleccionando el nuevo nivel funcional en el editor de licencias. NOTA: La selección de un nuevo nivel funcional no acompañado de la nueva clave de licencia de software dejará la unidad inutilizable. Si esto ocurriese, vuelva a ejecutar el editor de licencias y seleccione el nivel funcional correcto correspondiente a la clave de licencia de software instalada. ACTUALIZACIÓN DE INTELLEX 2.1 A 2.1L Instrucciones de Instalación Para obtener la clave de licencia de software debe rellenar un formulario de registro de licencia de software (nº de pieza 82000012-05 A) y enviarlo al número de fax de Sensormatic indicado en dicho formulario. La información que indique en el formulario de registro deberá ser completa y exacta para evitar la generación de una clave incorrecta o retrasos en su entrega. Algunos de los datos se obtienen de la unidad Intellex que se actualizará: Español NOTA: Los responsables de efectuar la instalación deberán anotar en el registro de mantenimiento (“Service Record”) todos los trabajos de actualización, reparación y nueva instalación realizados en la unidad. El registro debe conservarse en el interior de la carcasa. Si necesita obtener registros de mantenimiento nuevos o reposiciones, acuda a su distribuidor o directamente a Sensormatic (solicite el nº de pieza 2402-1587-01 A). Intellex® Sistema de Administración de Vídeo Digital 12 Obtención de la información de Intellex: 1. En la pantalla principal de Intellex, haga clic en Utilidad y luego en Acerca de Intellex. La versión del software debe ser 2.10.xx. Haga clic en Sistema. Al cabo de algunos segundos aparecerá una ventana con la dirección MAC. Anote la dirección MAC de 12 caracteres en el formulario de registro de la licencia de software. Haga clic en Aceptar y en Cerrar para cerrar esta pantalla y regresar a la pantalla principal. NOTA: Si la versión no es la 2.10.xx, no podrá utilizar este procedimiento para actualizar el software. Consulte al representante local de Sensormatic. 2. Anote el número de serie de Intellex en el formulario de registro de la licencia de software. El número de serie de Intellex aparece en la etiqueta del producto adherida a la parte inferior de la unidad o bien, en unidades recientes, en la etiqueta pegada dentro de la portezuela de la disquetera. 3. Anote el resto de los datos requeridos en el formulario de registro de licencia de software. El código de producto para esta actualización es RDVUPG21LA. El pedido de venta de Sensormatic se obtiene del Departamento de Atención al Cliente de Sensormatic en el momento de solicitar esta actualización. 4. Envíe el formulario de registro rellenado por fax al número indicado en el formulario. 5. Cuando reciba el formulario de respuesta de Sensormatic, contendrá la nueva clave de licencia de software. Introducción de la nueva clave de licencia y nivel funcional: NOTA: La salida al sistema operativo es una función protegida. Para acceder a ella, deberá disponer del permiso SALIR AL SISTEMA (consulte Configuración de seguridad en las Instrucciones de instalación de Intellex). 6. Desde la pantalla principal de Intellex, haga clic en Utilidad y luego en Salir. Aparece una pantalla de confirmación preguntando si desea salir del programa. Haga clic en Sí. Instrucciones para la actualización de la versión 2.1 de Intellex a la 2.1L 13 7. Introduzca el código PIN de salida en el teclado numérico y haga clic en Aceptar. 8. En el escritorio de Windows, haga doble clic en el icono Editor de licencias. Aparece la ventana del editor de licencias. 9. Compruebe si la dirección MAC visualizada en la ventana del editor de licencias coincide con la anotada en el formulario de registro de licencia de software. Si no coincide, haga clic en Cancelar y continúe con el paso 14. A continuación, consulte a su representante de Sensormatic. NOTA: La dirección MAC consta de 12 dígitos alfanuméricos, que pueden ser las cifras 0 a 9 y las letras “a” a la “f”. Cada unidad Intellex tiene una dirección MAC única. Si la ventana de direcciones MAC sólo contiene once dígitos, sitúe el puntero sobre la ventana y haga clic. A continuación, y manteniendo presionado el botón del mouse, deslice el puntero a la izquierda y a la derecha para ver los 12 caracteres. 10. En la ventana Nivel funcional, haga clic en el botón de flecha y seleccione la característica Live Display (Visualización en directo). 11. Anote la información de clave de licencia que aparezca en las cuatro ventanas. La necesitará para restaurar posteriormente el sistema a su estado actual. 12. Comenzando por la ventana izquierda, haga clic en cada una de las cuatro ventanas correspondientes a la clave de licencia y utilice la tecla RETROCESO para borrar el valor actual. A continuación, escriba la clave de licencia de software que aparece en el formulario de registro. NOTA: La clave de licencia consta de 16 caracteres (las cifras 0 a 9 y las letras a a f). Escriba las letras en minúsculas (nunca en MAYÚSCULAS). No puede haber espacios, guiones ni signos de puntuación. 13. Compruebe si la información introducida es correcta y haga clic en OK (Aceptar). 14. Haga doble clic en el icono Intellex para iniciar el software Intellex. 14 Intellex® Sistema de Administración de Vídeo Digital NOTA: Si Intellex no se ejecuta, debe haber un error en la clave de licencia. Repita el paso 8, introduzca la clave de licencia original y seleccione el nivel funcional original. A continuación, ejecute los pasos 12 y 13. Póngase en contacto con su representante de Sensormatic. Ahora su unidad Intellex está actualizada con “Live Remote Display”. Instrucciones para la actualización de la versión 2.1 de Intellex a la 2.1L NOTAS 15 Intellex® Digitales Video Management-System 16 Hinweis Die Angaben in diesem Handbuch befanden sich zum Zeitpunkt der Veröffentlichung auf dem neuesten Stand. Der Hersteller behält sich das Recht vor, seine Produkte zu überarbeiten und weiterzuentwickeln. Alle Angaben unterliegen daher Änderungen ohne vorherige Ankündigung. Copyright Gemäß der urheberrechtlichen Bestimmungen darf der Inhalt dieses Handbuchs ohne die vorherige schriftliche Zustimmung der Sensormatic Electronics Corporation weder vollständig noch teilweise vervielfältigt, übersetzt bzw. auf ein anderes elektronisches Medium oder in maschinenlesbare Form übertragen werden. © Copyright 2001 Warenzeichen Sensormatic Electronics Corporation Video Systems Division 6795 Flanders Drive San Diego, CA 92121-2903 U.S.A. Intellex® ist ein eingetragenes Warenzeichen und IntelleCord™ und Smart Search ™ sind Warenzeichen der Sensormatic Electronics Corporation. Windows® ist ein eingetragenens Warenzeichen der Microsoft Corporation. Als Warenzeichen geschützte Namen werden im gesamten Dokument verwendet. Das Warenzeichensymbol wird nur anfangs beigefügt und gilt gleichfalls bei jeder Erwähnung des Namens in diesem Handbuch. Die Angabe bzw. Nichtangabe dieses Symbols hat keinerlei Auswirkungen auf die Gültigkeit bzw. den rechtlichen Status des Warenzeichens. Anleitung für das Funktions-Upgrade von Intellex-Version 2.1 auf 2.1L 17 Funktions-Upgrade von Intellex 2.1 auf 2.1L Intellex 2.1 schränkt den Zugriff auf die Live Remote-Funktionalität (wenn sie zusammen mit Network Client 2.0 verwendet wird), abhängig von dem gewählten Funktionsumfang und dem Softwarelizenzierungsschlüssel, ein. Durch Eingabe eines neuen Software-lizenzierungsschlüssels und Auswahl eines neuen Funktionsumfangs im License Editor können Sie den Basisfunktionsumfang eines Intellex 2.1-Systems um die Live-Anzeige-Funktionalität erweitern. ANMERKUNG: Wenn Sie einen neuen Funktionsumfang wählen, ohne einen neuen Softwarelizenzierungsschlüssel einzugeben, ist das Gerät möglicherweise nicht mehr funktionsfähig. Starten Sie in diesem Fall den License Editor neu, und wählen Sie den richtigen Funktionsumfang für den installierten Softwarelizenzierungsschlüssel aus. ANMERKUNG: Erweiterungen, Reparaturen oder die Installation neuer Geräte sollten von der zuständigen Person auf dem Serviceaufkleber vermerkt werden. Bringen Sie diesen Aufkleber im Gehäuseinnern an. Serviceaufkleber für neue oder Ersatzteile erhalten Sie von Ihrem Händler oder von Sensormatic (Teilenummer 2402-1587-01 A). FUNKTIONS-UPGRADE VON INTELLEX 2.1 AUF 2.1L Installationsanleitung Deutsch Den Softwarelizenzierungsschlüssel erhalten Sie, wenn Sie die das Registrierungsformular für die Softwarelizenz (Teilenummer 8200-0012-00 A) ausgefüllt an die auf dem Fax angegebene Faxnummer senden. Bitte füllen Sie die Informationen auf diesem Registrierungsformular vollständig und sorgfältig aus. Andernfalls wird der Schlüssel möglicherweise nicht richtig programmiert oder die Lieferung ist mit Verzögerungen verbunden. Einige der Informationen finden Sie auf dem zu aktualisierenden Intellex-Gerät: Intellex® Digitales Video Management-System 18 Ermitteln der Intellex-Informationen 1. Klicken Sie im Intellex-Hauptbildschirm auf Dienste und dann auf Über Intellex. Die Software-Version muß 2.10.xx lauten. Klicken Sie auf System. Nach ein paar Sekunden wird ein Fenster mit der MAC-Adresse angezeigt. Notieren Sie die 12-stellige MAC-Adresse im Registrierungsformular für die Softwarelizenz. Klicken Sie auf OK und dann auf Beenden, um zum Hauptbildschirm zurückzukehren. ANMERKUNG: Falls die Version nicht 2.10.xx lautet, können Sie die Software nicht auf diese Weise aktualisieren. Setzen Sie sich in diesem Fall mit ihrem lokalen Sensormatic-Repräsentanten in Verbindung. 2. Notieren Sie die Intellex-Seriennummer im Registrierungsformular für die Softwarelizenz. Die Intellex-Seriennummer befindet sich auf dem Produktaufkleber auf der Unterseite des Intellex-Geräts oder, bei neueren Geräten, auf einem Aufkleber auf der Innenseite der Abdeckung für das Diskettenlaufwerk. 3. Tragen Sie die weiteren erforderlichen Informationen in das Registrierungsformular für die Softwarelizenz ein. Der Produktcode für diese Aktualisierung lautet RDVUPG21LA. Die Sensormatic-Auftragsnummer erhalten Sie vom Kundendienst bei Erteilung des Auftrags. 4. Faxen Sie das ausgefüllte Registrierungsformular für die Softwarelizenz an die auf dem Formular angegebene Nummer. 5. Sensormatic schickt Ihnen das Formular mit dem neuen Softwarelizenzierungsschlüssel zurück. Eingeben des neuen Lizenzierungsschlüssels und des Funktionsumfangs ANMERKUNG: Das Wechseln zurück zum System ist eine geschützte Funktion. Für den Zugriff brauchen Sie das Recht ZURÜCK ZUM SYSTEM (siehe Eingeben der Sicherheit in der Intellex-Installationsanleitung). 6. Klicken Sie im Hauptbildschirm auf Dienste und dann auf Beenden. Im eingeblendeten Bildschirm wird folgende Frage angezeigt: “Wollen Sie das Programm beenden?” Klicken Sie auf Ja. Anleitung für das Funktions-Upgrade von Intellex-Version 2.1 auf 2.1L 19 7. Geben Sie den PIN-Code zum Beenden ein und klicken Sie OK. 8. Doppelklicken Sie auf dem Windows-Desktop auf das Intellex-Symbol License Editor. Das Fenster License Editor wird angezeigt. 9. Überprüfen Sie, ob die im Fenster License Editor angezeigte MAC-Adresse mit der im Registrierungsformular für die Softwarelizenz angegebenen Adresse übereinstimmt. Falls die Adressen nicht übereinstimmen, klicken Sie auf Abbrechen und gehen Sie zu Schritt 14. Setzen Sie sich dann mit Ihrem Sensormatic-Repräsentanten in Verbindung. ANMERKUNG: Die MAC-Adresse ist 12 Zeichen lang und setzt sich aus Ziffern von 0 bis 9 und Buchstaben von a bis f zusammen und ist für jedes Intellex-Gerät eindeutig. Falls im Fenster MAC Address nur 11 Zeichen angezeigt werden, bewegen Sie den Mauszeiger auf das Fenster und klicken Sie anschließend. Halten Sie die linke Maustaste gedrückt und bewegen Sie den Mauszeiger von links nach rechts, um alle 12 Zeichen anzuzeigen. 10. Klicken Sie im Fenster Feature Level auf die Pfeil-Schaltfläche und wählen Sie Live Display. 11. Notieren Sie die in den vier Fenstern angezeigten Daten für den Lizenzierungsschlüssel. Diese Daten benötigen Sie, um das System wiederherstellen zu können. 12. Beginnen Sie im linken Fenster. Klicken Sie der Reihe nach in jedes der vier Fenster für den Lizenzierungsschlüssel und drücken Sie die Rücktaste, um den aktuellen Wert zu entfernen. Geben Sie dann den im Registrierungsformular für die Softwarelizenz aufgeführten Lizenzierungsschlüssel ein. ANMERKUNG: Der Lizenzierungsschlüssel besteht aus 16 Zeichen, die sich aus den Ziffern 0-9 und den Buchstaben a-f zusammensetzt. Geben Sie die Buchstaben in Kleinbuchstaben ein (GROSSBUCHSTABEN sind NICHT zulässig). Es sind keine Leerstellen, Gedankenstriche oder Interpunktionszeichen erlaubt. 13. Überprüfen Sie, ob die Informationen korrekt eingegeben wurden, und klicken Sie auf OK. 14. Doppelklicken Sie auf das Symbol Intellex, um die Intellex-Software zu starten. ANMERKUNG: Falls die Intellex-Software nicht startet, ist der Lizenzierungsschlüssel wahrscheinlich nicht richtig eingegeben. Wiederholen Sie Schritt 8 und geben Sie den Originallizenzierungsschlüssel ein. Wählen Sie zudem den Originalfunktionsumfang. Führen Sie dann die Schritte 12 und 13 durch. Setzen Sie sich mit Ihrem Sensormatic-Repräsentanten in Verbindung. Ihr Intellex-Gerät ist jetzt für die Live Remote-Anzeige aktualisiert. Sensormatic Video Systems Division 6795 Flanders Drive San Diego, California 92121-2903 TEL: 858-642-2400 800-854-2057 FAX: 858-642-2440 CustomerCare: 800-507-6268 Part Number 8200-0011-01 REV A