PN 04013
Transcripción
PN 04013
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: n Reorient or relocate the receiving antenna. n Increase the separation between the equipment and receiver. n Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. n Consult the dealer or an experienced radio/TV technician for help. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. PN 04013-50 rA 915 Overland Street North Salt Lake, UT 84054 USA Visit us online at www.hydrorain.com For additional information call 1.888.HYDRORAIN Este dispositivo cumple con la Parte 15 de la normativa FCC. La operación está sujeta a las siguientes dos condiciones: (1) Este dispositivo no puede causar interferencia nociva, y (2) Este dispositivo deberá aceptar cualquier interferencia incluyendo interferencia que ocasione operación no deseada. Advertencia: Los cambios o modificaciones a esta unidad que no hayan sido expresamente aprobados por la parte responsable para que cumplan con las normas podrían anular la autorización concedida al usuario para operar el equipo. NOTA: Este equipo ha sido probado y encontrado conforme a las limitaciones para dispositivo digital clase B, de acuerdo a la parte 15 de la normativa FCC. Estas limitaciones están diseñadas para proporcionar protección razonable contra interferencia dañina en una instalación residencial. Este equipo genera, utiliza y puede emitir energía de radiofrecuencia y, si no se instala y utiliza de acuerdo con las instrucciones, puede causar interferencia nociva a las comunicaciones de radio. No obstante, no hay garantía que la interferencia no ocurra en una instalación en particular. Si este equipo causa interferencia nociva a la recepción de radio o televisión, lo cual puede determinarse al activar o desactivar el equipo, se anima al usuario a tratar de corregir la interferencia por medio de una o más de las siguientes medidas: n Reorientar o reubicar la antena receptora. n Aumentar la separación entre el equipo y el recibidor. n Conectar el equipo a un tomacorriente en un circuito diferente de aquél en el cual el recibidor esté conectado. n Consultar al distribuidor o a un técnico experimentado en radio/TV para que le ayude. 915 Overland Street North Salt Lake, UT 84054 USA Visit us online at www.hydrorain.com For additional information call 1.888.HYDRORAIN PN 04013-50 rA proof no: 1 date: 03.20.09 des: MZ spck: MZ job no: N/A dimensions: Printers are flat: w: 5" h: 3" responsible for finished: w 5" h 3" d: NA meeting print production colors requirements. Registration DIE non printing color non printing CMYK PMS ???? PMS ???? Any changes must be approved client: Hydro-Rain sku: 04013 p 801 295 9820 f 801 951 5815 www.fluid-studio.net 1065 South 500 West Bountiful, Utah 84010 upc: N/A file name: 04013-50 rA.indd software: InDesign CS3 PMS ???? by the client and Fluid Studio. Printed piece additional instructions: Black Only must meet designated specifications on this form.