Reparto De La Pelicula Casino Royale
Transcripción
Reparto De La Pelicula Casino Royale
MORTARS PREPARED WITH POLITERM BLU SUPERLIGHT AGGREGATES FOR THE PREPARATION OF LIGHTWEIGHT THERMALLY INSULATING MORTARS POLITERM BLU HAS BEEN CHOSEN FOR: The lightweight mortars prepared with the superlight aggregates POLITERM BLU: • are made with expanded virgin EPS on beads treated with special E.I.A. additive at the production phase; • guarantee constancy and homogeneity of the dosages and of the thermal and mechanical characteristics; • do not shrink during the application nor the setting phase; • provide total dimensional stability of the mix over time. The castings do not crack nor swell; • the mixes can be pumped over long distances without undergoing physical or mechanical alterations; • they are lightweight, easy to apply and to transport; • they are PH-controlled and non-corrosive, hence the mixes do not trigger reactions of any kind with the materials with which they come into contact; • are idoneous to meet the insulating performances required by the related norms. The most complete range of superlight and highly thermal insulating aggregates based on pre-additivated virgin expanded polystyrene beads with controlled density. The coating of each single bead with E.I.A. additive is made in the production phase, wich allows perfect mixing with the water binder, homogeneous distribution in the mix and perfect pumping, thus eliminating the bead surfacing phenomenon in the mixture. Sandfree lightweight thermal insulating mortars can be prepared with the Politerm Blu products: mixes can be made just with Politerm Blu + cement + water (see dosage table). Ara Pacis Museum Rome, Italy Low Energy House Norway Bridge on the Po river Revere (Mantova), Italy TECHNICAL DATA Lafarge Factory Artemovsk, Ukraine lightweight thermally insulating screeds prepared with the products of the Politerm Blu range To obtain 200 litres of lightweight mortar 215 ~ 16-20 40 265 ~ 20-25 50 315 ~ 24-30 60 365 ~ 28-35 70 Politerm Blu Politerm Blu Fein n° 1 bag lt. 170 To obtain 1 m3 of lightweight mortar Dry Density Water Cement* kg/m3 kg lt. 215 ~ 80-100 200 265 ~ 100-125 250 315 ~ 120-150 300 365 ~ 140-175 350 TECHNICAL CHARACTERISTICS Cement dosage kg/m3 Politerm Blu Politerm Blu Fein n° 5 bags lt. 170 or National Theatre of Catalunya Spain Serralves Foundation Porto, Portugal Density after 28 day - kg/m3 Thermal conductivity - λ W/mk Compressive resistance (UNI EN 1015-11:2007) - N/mm2 Flexural strength (UNI EN 1015-11:2007) - N/mm2 Cohesion - kPa Hot-sealed membrane rupture - N/50 mm. Cold-sealed membrane rupture - N/50 mm. Elasticity module - N/mm 2 Permeability to water vapour - μ Shrinkage (NBN) - mm/m Specific heat - kj/kgK Impact sound reduction at 500 Hz - ΔL Le Meridien Hotel - Split, Croatia EDILTECO: AN INTERNATIONAL SUCCESS! n° 2 bags lt. 420 * use only Portland 32.5R cement or Cem I or high quality Cem II POLITERM BLU YIELDS SUPERLIGHT AGGREGATES FOR THE PREPARATION OF LIGHTWEIGHT THERMAL INSULATING MORTARS 500 lt. mortar 1 m3 mortar BAG lt. 170: 200 lt. mortar 1 m3 mortar LEGENDA production facilities distributors AZIENDA CON SISTEMA QUALITÀ CERTIFICATO DA DNV =UNI EN ISO 9001/2000= EDILTECO S.p.A. - Via dell’ Industria, 710 - 41038 San Felice s/P (MO) - Italia - Tel: +39 0535 82161 - Fax: +39 0535 82970 - [email protected] - www.edilteco.it © Copyright EDILTECO S.p.A. – non-authorized copy is forbidden – Producer has the faculty to modify his products without previous notice. BAG lt. 420: 200 250 300 350 ~ 215 0,065 0,69 0,37 82,62 57,00 35,00 235,30 10,11 0,427 1,40 n.a. ~ 265 0,067 0,83 0,46 82,62 n.a. n.a. n.a. 11,50 n.a. 1,40 14 dB ~ 315 0,080 1,61 0,95 127,17 62,00 47,00 489,50 12,00 0,352 1,40 21,5 dB ~ 365 0,103 1,69 0,59 n.a. 21,28 13,00 n.a. 21,04 0,270 1,40 n.a. n.a. n.a. n.a. Impact sound pressur level measure in situ UNI EN ISO 717-2 - L’nT,w (C1) Fire reactivity class Smoke production class Osservation of drops or inflamed particles ( thickness 5 cm ( thickness 11 cm A2 s1 d0 61 dB with acoustic ) ( insulation mat ) ) UNI EN 13501-1 UNI EN 13501-1 UNI EN 13501-1 DETERMINATION OF THE THERMAL RESISTANCE “R” AND THERMAL TRANSMITTANCE “U” COEFFICIENTS depending on the dosages of cement in the mix and the application thickness Cement kg/m3 © Copyright EDILTECO S.p.A.- Non authorized copy is forbidden Dry Density Water Cement* kg/m3 kg lt. 149 - 03-2010 PREPARATION OF SANDFREE LIGHTWEIGHT THERMAL INSULATING MORTARS 200 250 300 350 200 250 300 350 Thermal conductivity λ W/mk 0,065 0,067 0,080 0,103 0,065 0,067 0,080 0,103 Screed thickness cm. Coefficient R m k/W = ( thickness / λ) 2 U W/m2 k = 1/R 4 5 6 7 8 9 10 15 20 0,61 0,60 0,50 0,39 1,64 1,67 2,00 2,56 0,77 0,75 0,63 0,49 1,30 1,33 1,59 2,04 0,92 0,90 0,75 0,58 1,09 1,11 1,33 1,72 1,08 1,04 0,88 0,68 0,93 0,96 1,14 1,47 1,23 1,19 1,00 0,78 0,81 0,84 1,00 1,28 1,38 1,34 1,13 0,87 0,72 0,75 0,88 1,15 1,54 1,49 1,25 0,97 0,65 0,67 0,80 1,03 2,31 2,24 1,88 1,46 0,43 0,45 0,53 0,68 3,08 2,99 2,50 1,94 0,32 0,33 0,40 0,52 Consult the technical data sheets and the application manuals MORTARS PREPARED WITH POLITERM BLU SUPERLIGHT AGGREGATES FOR THE PREPARATION OF LIGHTWEIGHT THERMALLY INSULATING MORTARS POLITERM BLU HAS BEEN CHOSEN FOR: The lightweight mortars prepared with the superlight aggregates POLITERM BLU: • are made with expanded virgin EPS on beads treated with special E.I.A. additive at the production phase; • guarantee constancy and homogeneity of the dosages and of the thermal and mechanical characteristics; • do not shrink during the application nor the setting phase; • provide total dimensional stability of the mix over time. The castings do not crack nor swell; • the mixes can be pumped over long distances without undergoing physical or mechanical alterations; • they are lightweight, easy to apply and to transport; • they are PH-controlled and non-corrosive, hence the mixes do not trigger reactions of any kind with the materials with which they come into contact; • are idoneous to meet the insulating performances required by the related norms. The most complete range of superlight and highly thermal insulating aggregates based on pre-additivated virgin expanded polystyrene beads with controlled density. The coating of each single bead with E.I.A. additive is made in the production phase, wich allows perfect mixing with the water binder, homogeneous distribution in the mix and perfect pumping, thus eliminating the bead surfacing phenomenon in the mixture. Sandfree lightweight thermal insulating mortars can be prepared with the Politerm Blu products: mixes can be made just with Politerm Blu + cement + water (see dosage table). Ara Pacis Museum Rome, Italy Low Energy House Norway Bridge on the Po river Revere (Mantova), Italy TECHNICAL DATA Lafarge Factory Artemovsk, Ukraine lightweight thermally insulating screeds prepared with the products of the Politerm Blu range To obtain 200 litres of lightweight mortar 215 ~ 16-20 40 265 ~ 20-25 50 315 ~ 24-30 60 365 ~ 28-35 70 Politerm Blu Politerm Blu Fein n° 1 bag lt. 170 To obtain 1 m3 of lightweight mortar Dry Density Water Cement* kg/m3 kg lt. 215 ~ 80-100 200 265 ~ 100-125 250 315 ~ 120-150 300 365 ~ 140-175 350 TECHNICAL CHARACTERISTICS Cement dosage kg/m3 Politerm Blu Politerm Blu Fein n° 5 bags lt. 170 or National Theatre of Catalunya Spain Serralves Foundation Porto, Portugal Density after 28 day - kg/m3 Thermal conductivity - λ W/mk Compressive resistance (UNI EN 1015-11:2007) - N/mm2 Flexural strength (UNI EN 1015-11:2007) - N/mm2 Cohesion - kPa Hot-sealed membrane rupture - N/50 mm. Cold-sealed membrane rupture - N/50 mm. Elasticity module - N/mm 2 Permeability to water vapour - μ Shrinkage (NBN) - mm/m Specific heat - kj/kgK Impact sound reduction at 500 Hz - ΔL Le Meridien Hotel - Split, Croatia EDILTECO: AN INTERNATIONAL SUCCESS! n° 2 bags lt. 420 * use only Portland 32.5R cement or Cem I or high quality Cem II POLITERM BLU YIELDS SUPERLIGHT AGGREGATES FOR THE PREPARATION OF LIGHTWEIGHT THERMAL INSULATING MORTARS 500 lt. mortar 1 m3 mortar BAG lt. 170: 200 lt. mortar 1 m3 mortar LEGENDA production facilities distributors AZIENDA CON SISTEMA QUALITÀ CERTIFICATO DA DNV =UNI EN ISO 9001/2000= EDILTECO S.p.A. - Via dell’ Industria, 710 - 41038 San Felice s/P (MO) - Italia - Tel: +39 0535 82161 - Fax: +39 0535 82970 - [email protected] - www.edilteco.it © Copyright EDILTECO S.p.A. – non-authorized copy is forbidden – Producer has the faculty to modify his products without previous notice. BAG lt. 420: 200 250 300 350 ~ 215 0,065 0,69 0,37 82,62 57,00 35,00 235,30 10,11 0,427 1,40 n.a. ~ 265 0,067 0,83 0,46 82,62 n.a. n.a. n.a. 11,50 n.a. 1,40 14 dB ~ 315 0,080 1,61 0,95 127,17 62,00 47,00 489,50 12,00 0,352 1,40 21,5 dB ~ 365 0,103 1,69 0,59 n.a. 21,28 13,00 n.a. 21,04 0,270 1,40 n.a. n.a. n.a. n.a. Impact sound pressur level measure in situ UNI EN ISO 717-2 - L’nT,w (C1) Fire reactivity class Smoke production class Osservation of drops or inflamed particles ( thickness 5 cm ( thickness 11 cm A2 s1 d0 61 dB with acoustic ) ( insulation mat ) ) UNI EN 13501-1 UNI EN 13501-1 UNI EN 13501-1 DETERMINATION OF THE THERMAL RESISTANCE “R” AND THERMAL TRANSMITTANCE “U” COEFFICIENTS depending on the dosages of cement in the mix and the application thickness Cement kg/m3 © Copyright EDILTECO S.p.A.- Non authorized copy is forbidden Dry Density Water Cement* kg/m3 kg lt. 149 - 03-2010 PREPARATION OF SANDFREE LIGHTWEIGHT THERMAL INSULATING MORTARS 200 250 300 350 200 250 300 350 Thermal conductivity λ W/mk 0,065 0,067 0,080 0,103 0,065 0,067 0,080 0,103 Screed thickness cm. Coefficient R m k/W = ( thickness / λ) 2 U W/m2 k = 1/R 4 5 6 7 8 9 10 15 20 0,61 0,60 0,50 0,39 1,64 1,67 2,00 2,56 0,77 0,75 0,63 0,49 1,30 1,33 1,59 2,04 0,92 0,90 0,75 0,58 1,09 1,11 1,33 1,72 1,08 1,04 0,88 0,68 0,93 0,96 1,14 1,47 1,23 1,19 1,00 0,78 0,81 0,84 1,00 1,28 1,38 1,34 1,13 0,87 0,72 0,75 0,88 1,15 1,54 1,49 1,25 0,97 0,65 0,67 0,80 1,03 2,31 2,24 1,88 1,46 0,43 0,45 0,53 0,68 3,08 2,99 2,50 1,94 0,32 0,33 0,40 0,52 Consult the technical data sheets and the application manuals MORTARS PREPARED WITH POLITERM BLU SUPERLIGHT AGGREGATES FOR THE PREPARATION OF LIGHTWEIGHT THERMALLY INSULATING MORTARS POLITERM BLU HAS BEEN CHOSEN FOR: The lightweight mortars prepared with the superlight aggregates POLITERM BLU: • are made with expanded virgin EPS on beads treated with special E.I.A. additive at the production phase; • guarantee constancy and homogeneity of the dosages and of the thermal and mechanical characteristics; • do not shrink during the application nor the setting phase; • provide total dimensional stability of the mix over time. The castings do not crack nor swell; • the mixes can be pumped over long distances without undergoing physical or mechanical alterations; • they are lightweight, easy to apply and to transport; • they are PH-controlled and non-corrosive, hence the mixes do not trigger reactions of any kind with the materials with which they come into contact; • are idoneous to meet the insulating performances required by the related norms. The most complete range of superlight and highly thermal insulating aggregates based on pre-additivated virgin expanded polystyrene beads with controlled density. The coating of each single bead with E.I.A. additive is made in the production phase, wich allows perfect mixing with the water binder, homogeneous distribution in the mix and perfect pumping, thus eliminating the bead surfacing phenomenon in the mixture. Sandfree lightweight thermal insulating mortars can be prepared with the Politerm Blu products: mixes can be made just with Politerm Blu + cement + water (see dosage table). Ara Pacis Museum Rome, Italy Low Energy House Norway Bridge on the Po river Revere (Mantova), Italy TECHNICAL DATA Lafarge Factory Artemovsk, Ukraine lightweight thermally insulating screeds prepared with the products of the Politerm Blu range To obtain 200 litres of lightweight mortar 215 ~ 16-20 40 265 ~ 20-25 50 315 ~ 24-30 60 365 ~ 28-35 70 Politerm Blu Politerm Blu Fein n° 1 bag lt. 170 To obtain 1 m3 of lightweight mortar Dry Density Water Cement* kg/m3 kg lt. 215 ~ 80-100 200 265 ~ 100-125 250 315 ~ 120-150 300 365 ~ 140-175 350 TECHNICAL CHARACTERISTICS Cement dosage kg/m3 Politerm Blu Politerm Blu Fein n° 5 bags lt. 170 or National Theatre of Catalunya Spain Serralves Foundation Porto, Portugal Density after 28 day - kg/m3 Thermal conductivity - λ W/mk Compressive resistance (UNI EN 1015-11:2007) - N/mm2 Flexural strength (UNI EN 1015-11:2007) - N/mm2 Cohesion - kPa Hot-sealed membrane rupture - N/50 mm. Cold-sealed membrane rupture - N/50 mm. Elasticity module - N/mm 2 Permeability to water vapour - μ Shrinkage (NBN) - mm/m Specific heat - kj/kgK Impact sound reduction at 500 Hz - ΔL Le Meridien Hotel - Split, Croatia EDILTECO: AN INTERNATIONAL SUCCESS! n° 2 bags lt. 420 * use only Portland 32.5R cement or Cem I or high quality Cem II POLITERM BLU YIELDS SUPERLIGHT AGGREGATES FOR THE PREPARATION OF LIGHTWEIGHT THERMAL INSULATING MORTARS 500 lt. mortar 1 m3 mortar BAG lt. 170: 200 lt. mortar 1 m3 mortar LEGENDA production facilities distributors AZIENDA CON SISTEMA QUALITÀ CERTIFICATO DA DNV =UNI EN ISO 9001/2000= EDILTECO S.p.A. - Via dell’ Industria, 710 - 41038 San Felice s/P (MO) - Italia - Tel: +39 0535 82161 - Fax: +39 0535 82970 - [email protected] - www.edilteco.it © Copyright EDILTECO S.p.A. – non-authorized copy is forbidden – Producer has the faculty to modify his products without previous notice. BAG lt. 420: 200 250 300 350 ~ 215 0,065 0,69 0,37 82,62 57,00 35,00 235,30 10,11 0,427 1,40 n.a. ~ 265 0,067 0,83 0,46 82,62 n.a. n.a. n.a. 11,50 n.a. 1,40 14 dB ~ 315 0,080 1,61 0,95 127,17 62,00 47,00 489,50 12,00 0,352 1,40 21,5 dB ~ 365 0,103 1,69 0,59 n.a. 21,28 13,00 n.a. 21,04 0,270 1,40 n.a. n.a. n.a. n.a. Impact sound pressur level measure in situ UNI EN ISO 717-2 - L’nT,w (C1) Fire reactivity class Smoke production class Osservation of drops or inflamed particles ( thickness 5 cm ( thickness 11 cm A2 s1 d0 61 dB with acoustic ) ( insulation mat ) ) UNI EN 13501-1 UNI EN 13501-1 UNI EN 13501-1 DETERMINATION OF THE THERMAL RESISTANCE “R” AND THERMAL TRANSMITTANCE “U” COEFFICIENTS depending on the dosages of cement in the mix and the application thickness Cement kg/m3 © Copyright EDILTECO S.p.A.- Non authorized copy is forbidden Dry Density Water Cement* kg/m3 kg lt. 149 - 03-2010 PREPARATION OF SANDFREE LIGHTWEIGHT THERMAL INSULATING MORTARS 200 250 300 350 200 250 300 350 Thermal conductivity λ W/mk 0,065 0,067 0,080 0,103 0,065 0,067 0,080 0,103 Screed thickness cm. Coefficient R m k/W = ( thickness / λ) 2 U W/m2 k = 1/R 4 5 6 7 8 9 10 15 20 0,61 0,60 0,50 0,39 1,64 1,67 2,00 2,56 0,77 0,75 0,63 0,49 1,30 1,33 1,59 2,04 0,92 0,90 0,75 0,58 1,09 1,11 1,33 1,72 1,08 1,04 0,88 0,68 0,93 0,96 1,14 1,47 1,23 1,19 1,00 0,78 0,81 0,84 1,00 1,28 1,38 1,34 1,13 0,87 0,72 0,75 0,88 1,15 1,54 1,49 1,25 0,97 0,65 0,67 0,80 1,03 2,31 2,24 1,88 1,46 0,43 0,45 0,53 0,68 3,08 2,99 2,50 1,94 0,32 0,33 0,40 0,52 Consult the technical data sheets and the application manuals MORTARS PREPARED WITH POLITERM BLU SUPERLIGHT AGGREGATES FOR THE PREPARATION OF LIGHTWEIGHT THERMALLY INSULATING MORTARS POLITERM BLU HAS BEEN CHOSEN FOR: The lightweight mortars prepared with the superlight aggregates POLITERM BLU: • are made with expanded virgin EPS on beads treated with special E.I.A. additive at the production phase; • guarantee constancy and homogeneity of the dosages and of the thermal and mechanical characteristics; • do not shrink during the application nor the setting phase; • provide total dimensional stability of the mix over time. The castings do not crack nor swell; • the mixes can be pumped over long distances without undergoing physical or mechanical alterations; • they are lightweight, easy to apply and to transport; • they are PH-controlled and non-corrosive, hence the mixes do not trigger reactions of any kind with the materials with which they come into contact; • are idoneous to meet the insulating performances required by the related norms. The most complete range of superlight and highly thermal insulating aggregates based on pre-additivated virgin expanded polystyrene beads with controlled density. The coating of each single bead with E.I.A. additive is made in the production phase, wich allows perfect mixing with the water binder, homogeneous distribution in the mix and perfect pumping, thus eliminating the bead surfacing phenomenon in the mixture. Sandfree lightweight thermal insulating mortars can be prepared with the Politerm Blu products: mixes can be made just with Politerm Blu + cement + water (see dosage table). Ara Pacis Museum Rome, Italy Low Energy House Norway Bridge on the Po river Revere (Mantova), Italy TECHNICAL DATA Lafarge Factory Artemovsk, Ukraine lightweight thermally insulating screeds prepared with the products of the Politerm Blu range To obtain 200 litres of lightweight mortar 215 ~ 16-20 40 265 ~ 20-25 50 315 ~ 24-30 60 365 ~ 28-35 70 Politerm Blu Politerm Blu Fein n° 1 bag lt. 170 To obtain 1 m3 of lightweight mortar Dry Density Water Cement* kg/m3 kg lt. 215 ~ 80-100 200 265 ~ 100-125 250 315 ~ 120-150 300 365 ~ 140-175 350 TECHNICAL CHARACTERISTICS Cement dosage kg/m3 Politerm Blu Politerm Blu Fein n° 5 bags lt. 170 or National Theatre of Catalunya Spain Serralves Foundation Porto, Portugal Density after 28 day - kg/m3 Thermal conductivity - λ W/mk Compressive resistance (UNI EN 1015-11:2007) - N/mm2 Flexural strength (UNI EN 1015-11:2007) - N/mm2 Cohesion - kPa Hot-sealed membrane rupture - N/50 mm. Cold-sealed membrane rupture - N/50 mm. Elasticity module - N/mm 2 Permeability to water vapour - μ Shrinkage (NBN) - mm/m Specific heat - kj/kgK Impact sound reduction at 500 Hz - ΔL Le Meridien Hotel - Split, Croatia EDILTECO: AN INTERNATIONAL SUCCESS! n° 2 bags lt. 420 * use only Portland 32.5R cement or Cem I or high quality Cem II POLITERM BLU YIELDS SUPERLIGHT AGGREGATES FOR THE PREPARATION OF LIGHTWEIGHT THERMAL INSULATING MORTARS 500 lt. mortar 1 m3 mortar BAG lt. 170: 200 lt. mortar 1 m3 mortar LEGENDA production facilities distributors AZIENDA CON SISTEMA QUALITÀ CERTIFICATO DA DNV =UNI EN ISO 9001/2000= EDILTECO S.p.A. - Via dell’ Industria, 710 - 41038 San Felice s/P (MO) - Italia - Tel: +39 0535 82161 - Fax: +39 0535 82970 - [email protected] - www.edilteco.it © Copyright EDILTECO S.p.A. – non-authorized copy is forbidden – Producer has the faculty to modify his products without previous notice. BAG lt. 420: 200 250 300 350 ~ 215 0,065 0,69 0,37 82,62 57,00 35,00 235,30 10,11 0,427 1,40 n.a. ~ 265 0,067 0,83 0,46 82,62 n.a. n.a. n.a. 11,50 n.a. 1,40 14 dB ~ 315 0,080 1,61 0,95 127,17 62,00 47,00 489,50 12,00 0,352 1,40 21,5 dB ~ 365 0,103 1,69 0,59 n.a. 21,28 13,00 n.a. 21,04 0,270 1,40 n.a. n.a. n.a. n.a. Impact sound pressur level measure in situ UNI EN ISO 717-2 - L’nT,w (C1) Fire reactivity class Smoke production class Osservation of drops or inflamed particles ( thickness 5 cm ( thickness 11 cm A2 s1 d0 61 dB with acoustic ) ( insulation mat ) ) UNI EN 13501-1 UNI EN 13501-1 UNI EN 13501-1 DETERMINATION OF THE THERMAL RESISTANCE “R” AND THERMAL TRANSMITTANCE “U” COEFFICIENTS depending on the dosages of cement in the mix and the application thickness Cement kg/m3 © Copyright EDILTECO S.p.A.- Non authorized copy is forbidden Dry Density Water Cement* kg/m3 kg lt. 149 - 03-2010 PREPARATION OF SANDFREE LIGHTWEIGHT THERMAL INSULATING MORTARS 200 250 300 350 200 250 300 350 Thermal conductivity λ W/mk 0,065 0,067 0,080 0,103 0,065 0,067 0,080 0,103 Screed thickness cm. Coefficient R m k/W = ( thickness / λ) 2 U W/m2 k = 1/R 4 5 6 7 8 9 10 15 20 0,61 0,60 0,50 0,39 1,64 1,67 2,00 2,56 0,77 0,75 0,63 0,49 1,30 1,33 1,59 2,04 0,92 0,90 0,75 0,58 1,09 1,11 1,33 1,72 1,08 1,04 0,88 0,68 0,93 0,96 1,14 1,47 1,23 1,19 1,00 0,78 0,81 0,84 1,00 1,28 1,38 1,34 1,13 0,87 0,72 0,75 0,88 1,15 1,54 1,49 1,25 0,97 0,65 0,67 0,80 1,03 2,31 2,24 1,88 1,46 0,43 0,45 0,53 0,68 3,08 2,99 2,50 1,94 0,32 0,33 0,40 0,52 Consult the technical data sheets and the application manuals POLITERM MACHINE electrical power supply POLITERM MACHINE Diesel Pump-mixer for lightweight thermal insulating mortars based on: • polystyrene beads • cellular/foam concrete • perlite • cork Pump-mixer for lightweight thermal insulating mortars based on: • polystyrene beads • cellular/foam concrete • perlite • cork Pumping capacity up to 120 m distance and 30 m head (60 m with metal pipes) Pumping capacity up to 120 m distance and 30 m head (60 m with metal pipes) Power supply voltage: 380V Available with tank of: • 1 m3 Models: • ECO • H2O (automatic dosage of water) Available with tank of: • 1 m3 • 0,5 m3 High productivity: up to 10 m3/h Hydraulic control unit driven by a diesel engine homologated in compliance with the regulations regarding noise pollution. Possibility of customised fittings. High productivity: up to 10 m3/h PRODUCTS DESCRIPTION Building elements* • Blocks: 7 • Pre-casted wall 10 Intermediate layer - Filling • system levelling; 11 • under sand + cement screeds; 8 • under self-levelling screeds; 8 • under floor radiating heating (also with direct laying of the coils); 6 • vaulted floor levelling; 9 • under industrial flooring; • under driveable asphalt mantles; • in-between wall thermally insulating layer. 3 And also: • Gradient formation for terraces. 4 ISOLCAP MACHINE POLITERM PUMP Pump-mixer for: Pump for lightweight thermal insulating mortars based on: • polystyrene beads • cellular /foam concrete • perlite • cork • Lightweight mortars • Self-leveling mortars Weight: 128 kg. Tank capacity: approx. 260 lt. Power supply: electric with 6 kw 380/220 V Pumping maximum distance: approx. 50 mt. 1 Roofing • pitched roofs; 1 • flat roofs with or without gradient formation; • vaulted roofs; • corrugated sheet iron; • asbestos cement fibres (encapsulation); • also with direct application of waterproofing membrane. 2 Hopper capacity: lt. 200 approximately Versatile and portable. High productivity: up to 30 m3/h Preparation with cement mixer • granulometry 3-6 mm; • excellent also for the use in large mixing tank. 1. 2. 3. 4. 5. 6. 7. 8. 9. POLITERM BLU FEIN: water: as much as required for the mix (*) less 20-30 litres (point 7); Politerm Blu Ready Mix or Politerm Blu Fein Ready Mix; mix for about 10 minutes at maximum speed; sand if necessary (*) ; cement (*) ; mix for about 10 minutes at maximum speed; clean the loading bowl with about 20-30 litres of water (thus completing dosage of the mixing water); depending on the residual moisture in the sand (if any), add more water; on the way from the batch plant to the building site the cement mixer must turn at top speed for the first 20 minutes and then at minimum speed. COMPLEMENTARY PRODUCTS • granulometry 2 mm; • improved surface compactness. 2 PIANO ZERO SYSTEM RS MALTA L Throwaway PVC guide for the formation of level strips. Premixed antishrinkage smoothing mortar with very fast dehydration feature. To be used when making single-layer lightweight screeds. Profile height 5 cm The special cross-section design allows: • perfetct incorporation in the casting; • indeformability; • maintaining alignment; • preventing the formation of thermal bridges. 3 5 6 Equipment for sanding the surfaces of lightweight thermal insulating screeds. Synthetic latex to prepare adhesion bridges or improve the properties of cement mortars. Power supply voltage: 230V EDILSTIK BLOW MACHINE POLITAINER Latex spraying equipment (eg Edilstik FCA) Integrated logistics system for the delivery and the storage of the Politerm Blu range bags. Power supply voltage: 230V / 50Hz 7 ith red w prepa RM BLU s d e E re The sc ducts POLIT Therefore . o e the pr fectly stable ing surfac , y r n la e o l p ti a are ide sula re the und in they a type of so technical . y e ir for an ranting the ng the tim lo a ga s e c rman perfo To be used in execution of single-layer lightweight screeds (Piano Zero system): • to promote adhesion to the laying surface • for preparation of very thin smoothing mortars for surface protection. 10 Packaging: • bottles of 1 kg; • cans of 5 kg; cans of 20 kg. Palletised containers of 1000 kg 8 9 Edilstik can also be used: • as additive to the hydration water for traditional sand+cement screeds with anti shrinkage and/or adhesion improvement function; • to prepare grout or films for “fresh on fresh” application to improve adhesion on poorly absorbent surfaces for subsequent application of traditional sand+cement screeds or plasters. EDILSTIK FCA Pigmented synthetic latex for temporary inertisation of asbestos cement fibre sheets (certifi cate type “D”). To be applied before encapsulation work with lightweight thermal insulating mortars prepared with products of the Politerm Blu range. 11 �������� Packaging: • cans of 5 kg; cans of 20 kg. Palletised tanks of 1000 kg. Colour: yellow-orange Low-pressure application with spray nozzle (see Edilstik Blow Machine) or airless. * Mainly for partitional elements. Structural calculation is under responsability of the project engineer according to local regulations. Consult the technical data sheets and the application manuals Parquet and resilient flooring can be laid 24 hours after application. Ready mix self levelling smoothing mortar for thin-bed applications, ready to use, for manual as well as mechanical application. Screw for loading cement into the Politerm Machine tank Particularly suitable for surface finishing of single-layer lightweight thermal insulating screeds (Piano Zero system). Bags of 25 kg AUTOLIV EDILSTIK Make your job easier! • parquet (min. thickness Rs Malta L: 5 mm); • PVC, linoleum, rubber, carpeting (min thickness Rs Malta L: 20 mm). Electronic leveling tool with level display ELECTRICAL SANDERS Available types: • double-brush (2 discs) • single-brush (1 disc) To be used on single-layer lightweight screeds (Piano Zero system) for gluing of floor coverings as: LIVELLO PIANO ZERO POLITERM MACHINE SCREW Possibility of customised fittings. To obtain 1 m3 of finished mortar: 1. water (*) ; 2. first 420 lt. bag of Politerm Blu or Politerm Blu Fein; 3. cement (*) ; 4. second 420 lt. bag of Politerm Blu or Politerm Blu Fein; 5. continue mixing for 5 minutes; 6. pump. Preparation with truck-mixer Guides of 2 m each 4 Power supply voltage: 380V Preparation with Politerm Machine To obtain 200 lt of finished mortar: 1. water (*); 2. Politerm Blu or Politerm Blu Fein (1 bag of 170 lt); 3. cement (*); 4. sand (if necessary); 5. continue mixing for 5 minutes holding the bowl in an as horizontal as possible position; 6. pour the mortar. POLITERM BLU: > powered by: electric supply or hydraulic engine by means of power take-off (e.g.truck) > with or without the hopper for loading the mortar Productivity: up to 3 m /h 3 Superlight aggregates composed by virgin expanded polystyrene beads treated with the special E.I.A. additive for the preparation of lightweight and thermal insulating cement mixes. Politerm is used as thermally insulating and lightening material. Single-layer screeds Direct application of: • Ceramic, stoneware, clinker and prepolished marble floor coverings and laying of floating parquets; 5 • Parquets, after applying a thin-bed compound; 8 • Flexible flooring (carpet, pvc...), after application of thin-bed smoothing compound. 8 MIXING PREPARATION STEPS main indications *The dosages of the various components have to follow the prescriptions issued by Edilteco S.p.A. APPLICATIONS © Copyright EDILTECO S.p.A.- non-authorized copy is forbidden - Edilteco has the faculty to modify the products without previous notice. consultate schede tecniche e manuali di posa in opera High resistant levellings of cement screeds. It constitutes a support suitable for floor in PVC, carpet, laminated parquet, ceramic, epoxidic resins and polyurethane resins. Suitable for high resistance correction or levelling of screeds prepared with Politerm Blu or Isolcap, before the laying of ceramic tiles, porcelain stoneware, marble stoneware, natural stones and parquet. AUTOLIV M Self levelling screed. Autoliv M is a powder product for the preparation of cement-based self levelling screeds. For the application detached from the support: on top of polyethylene the application thickness of the product should be 30 mm, whilst on top of squeezable insulating materials is 40 mm. For the application in attachment to the support: application thickness from 20 mm. AUTOLIV SP Cement-based self-levelling screed. Autoliv SP is a powder product for the preparation of cement-based self-levelling screeds. The product can be applied in thicknesses varying from 4 to 8 cm. as a substitute of the traditional screed and to cover radiating underfloor heating systems. © Copyright EDILTECO S.p.A. – non-authorized copy is forbidden – Producer has the faculty to modify his products without previous notice. SPECIFIC EQUIPMENTS POLITERM MACHINE electrical power supply POLITERM MACHINE Diesel Pump-mixer for lightweight thermal insulating mortars based on: • polystyrene beads • cellular/foam concrete • perlite • cork Pump-mixer for lightweight thermal insulating mortars based on: • polystyrene beads • cellular/foam concrete • perlite • cork Pumping capacity up to 120 m distance and 30 m head (60 m with metal pipes) Pumping capacity up to 120 m distance and 30 m head (60 m with metal pipes) Power supply voltage: 380V Available with tank of: • 1 m3 Models: • ECO • H2O (automatic dosage of water) Available with tank of: • 1 m3 • 0,5 m3 High productivity: up to 10 m3/h Hydraulic control unit driven by a diesel engine homologated in compliance with the regulations regarding noise pollution. Possibility of customised fittings. High productivity: up to 10 m3/h PRODUCTS DESCRIPTION Building elements* • Blocks: 7 • Pre-casted wall 10 Intermediate layer - Filling • system levelling; 11 • under sand + cement screeds; 8 • under self-levelling screeds; 8 • under floor radiating heating (also with direct laying of the coils); 6 • vaulted floor levelling; 9 • under industrial flooring; • under driveable asphalt mantles; • in-between wall thermally insulating layer. 3 And also: • Gradient formation for terraces. 4 ISOLCAP MACHINE POLITERM PUMP Pump-mixer for: Pump for lightweight thermal insulating mortars based on: • polystyrene beads • cellular /foam concrete • perlite • cork • Lightweight mortars • Self-leveling mortars Weight: 128 kg. Tank capacity: approx. 260 lt. Power supply: electric with 6 kw 380/220 V Pumping maximum distance: approx. 50 mt. 1 Roofing • pitched roofs; 1 • flat roofs with or without gradient formation; • vaulted roofs; • corrugated sheet iron; • asbestos cement fibres (encapsulation); • also with direct application of waterproofing membrane. 2 Hopper capacity: lt. 200 approximately Versatile and portable. High productivity: up to 30 m3/h Preparation with cement mixer • granulometry 3-6 mm; • excellent also for the use in large mixing tank. 1. 2. 3. 4. 5. 6. 7. 8. 9. POLITERM BLU FEIN: water: as much as required for the mix (*) less 20-30 litres (point 7); Politerm Blu Ready Mix or Politerm Blu Fein Ready Mix; mix for about 10 minutes at maximum speed; sand if necessary (*) ; cement (*) ; mix for about 10 minutes at maximum speed; clean the loading bowl with about 20-30 litres of water (thus completing dosage of the mixing water); depending on the residual moisture in the sand (if any), add more water; on the way from the batch plant to the building site the cement mixer must turn at top speed for the first 20 minutes and then at minimum speed. COMPLEMENTARY PRODUCTS • granulometry 2 mm; • improved surface compactness. 2 PIANO ZERO SYSTEM RS MALTA L Throwaway PVC guide for the formation of level strips. Premixed antishrinkage smoothing mortar with very fast dehydration feature. To be used when making single-layer lightweight screeds. Profile height 5 cm The special cross-section design allows: • perfetct incorporation in the casting; • indeformability; • maintaining alignment; • preventing the formation of thermal bridges. 3 5 6 Equipment for sanding the surfaces of lightweight thermal insulating screeds. Synthetic latex to prepare adhesion bridges or improve the properties of cement mortars. Power supply voltage: 230V EDILSTIK BLOW MACHINE POLITAINER Latex spraying equipment (eg Edilstik FCA) Integrated logistics system for the delivery and the storage of the Politerm Blu range bags. Power supply voltage: 230V / 50Hz 7 ith red w prepa RM BLU s d e E re The sc ducts POLIT Therefore . o e the pr fectly stable ing surfac , y r n la e o l p ti a are ide sula re the und in they a type of so technical . y e ir for an ranting the ng the tim lo a ga s e c rman perfo To be used in execution of single-layer lightweight screeds (Piano Zero system): • to promote adhesion to the laying surface • for preparation of very thin smoothing mortars for surface protection. 10 Packaging: • bottles of 1 kg; • cans of 5 kg; cans of 20 kg. Palletised containers of 1000 kg 8 9 Edilstik can also be used: • as additive to the hydration water for traditional sand+cement screeds with anti shrinkage and/or adhesion improvement function; • to prepare grout or films for “fresh on fresh” application to improve adhesion on poorly absorbent surfaces for subsequent application of traditional sand+cement screeds or plasters. EDILSTIK FCA Pigmented synthetic latex for temporary inertisation of asbestos cement fibre sheets (certifi cate type “D”). To be applied before encapsulation work with lightweight thermal insulating mortars prepared with products of the Politerm Blu range. 11 �������� Packaging: • cans of 5 kg; cans of 20 kg. Palletised tanks of 1000 kg. Colour: yellow-orange Low-pressure application with spray nozzle (see Edilstik Blow Machine) or airless. * Mainly for partitional elements. Structural calculation is under responsability of the project engineer according to local regulations. Consult the technical data sheets and the application manuals Parquet and resilient flooring can be laid 24 hours after application. Ready mix self levelling smoothing mortar for thin-bed applications, ready to use, for manual as well as mechanical application. Screw for loading cement into the Politerm Machine tank Particularly suitable for surface finishing of single-layer lightweight thermal insulating screeds (Piano Zero system). Bags of 25 kg AUTOLIV EDILSTIK Make your job easier! • parquet (min. thickness Rs Malta L: 5 mm); • PVC, linoleum, rubber, carpeting (min thickness Rs Malta L: 20 mm). Electronic leveling tool with level display ELECTRICAL SANDERS Available types: • double-brush (2 discs) • single-brush (1 disc) To be used on single-layer lightweight screeds (Piano Zero system) for gluing of floor coverings as: LIVELLO PIANO ZERO POLITERM MACHINE SCREW Possibility of customised fittings. To obtain 1 m3 of finished mortar: 1. water (*) ; 2. first 420 lt. bag of Politerm Blu or Politerm Blu Fein; 3. cement (*) ; 4. second 420 lt. bag of Politerm Blu or Politerm Blu Fein; 5. continue mixing for 5 minutes; 6. pump. Preparation with truck-mixer Guides of 2 m each 4 Power supply voltage: 380V Preparation with Politerm Machine To obtain 200 lt of finished mortar: 1. water (*); 2. Politerm Blu or Politerm Blu Fein (1 bag of 170 lt); 3. cement (*); 4. sand (if necessary); 5. continue mixing for 5 minutes holding the bowl in an as horizontal as possible position; 6. pour the mortar. POLITERM BLU: > powered by: electric supply or hydraulic engine by means of power take-off (e.g.truck) > with or without the hopper for loading the mortar Productivity: up to 3 m /h 3 Superlight aggregates composed by virgin expanded polystyrene beads treated with the special E.I.A. additive for the preparation of lightweight and thermal insulating cement mixes. Politerm is used as thermally insulating and lightening material. Single-layer screeds Direct application of: • Ceramic, stoneware, clinker and prepolished marble floor coverings and laying of floating parquets; 5 • Parquets, after applying a thin-bed compound; 8 • Flexible flooring (carpet, pvc...), after application of thin-bed smoothing compound. 8 MIXING PREPARATION STEPS main indications *The dosages of the various components have to follow the prescriptions issued by Edilteco S.p.A. APPLICATIONS © Copyright EDILTECO S.p.A.- non-authorized copy is forbidden - Edilteco has the faculty to modify the products without previous notice. consultate schede tecniche e manuali di posa in opera High resistant levellings of cement screeds. It constitutes a support suitable for floor in PVC, carpet, laminated parquet, ceramic, epoxidic resins and polyurethane resins. Suitable for high resistance correction or levelling of screeds prepared with Politerm Blu or Isolcap, before the laying of ceramic tiles, porcelain stoneware, marble stoneware, natural stones and parquet. AUTOLIV M Self levelling screed. Autoliv M is a powder product for the preparation of cement-based self levelling screeds. For the application detached from the support: on top of polyethylene the application thickness of the product should be 30 mm, whilst on top of squeezable insulating materials is 40 mm. For the application in attachment to the support: application thickness from 20 mm. AUTOLIV SP Cement-based self-levelling screed. Autoliv SP is a powder product for the preparation of cement-based self-levelling screeds. The product can be applied in thicknesses varying from 4 to 8 cm. as a substitute of the traditional screed and to cover radiating underfloor heating systems. © Copyright EDILTECO S.p.A. – non-authorized copy is forbidden – Producer has the faculty to modify his products without previous notice. SPECIFIC EQUIPMENTS POLITERM MACHINE electrical power supply POLITERM MACHINE Diesel Pump-mixer for lightweight thermal insulating mortars based on: • polystyrene beads • cellular/foam concrete • perlite • cork Pump-mixer for lightweight thermal insulating mortars based on: • polystyrene beads • cellular/foam concrete • perlite • cork Pumping capacity up to 120 m distance and 30 m head (60 m with metal pipes) Pumping capacity up to 120 m distance and 30 m head (60 m with metal pipes) Power supply voltage: 380V Available with tank of: • 1 m3 Models: • ECO • H2O (automatic dosage of water) Available with tank of: • 1 m3 • 0,5 m3 High productivity: up to 10 m3/h Hydraulic control unit driven by a diesel engine homologated in compliance with the regulations regarding noise pollution. Possibility of customised fittings. High productivity: up to 10 m3/h PRODUCTS DESCRIPTION Building elements* • Blocks: 7 • Pre-casted wall 10 Intermediate layer - Filling • system levelling; 11 • under sand + cement screeds; 8 • under self-levelling screeds; 8 • under floor radiating heating (also with direct laying of the coils); 6 • vaulted floor levelling; 9 • under industrial flooring; • under driveable asphalt mantles; • in-between wall thermally insulating layer. 3 And also: • Gradient formation for terraces. 4 ISOLCAP MACHINE POLITERM PUMP Pump-mixer for: Pump for lightweight thermal insulating mortars based on: • polystyrene beads • cellular /foam concrete • perlite • cork • Lightweight mortars • Self-leveling mortars Weight: 128 kg. Tank capacity: approx. 260 lt. Power supply: electric with 6 kw 380/220 V Pumping maximum distance: approx. 50 mt. 1 Roofing • pitched roofs; 1 • flat roofs with or without gradient formation; • vaulted roofs; • corrugated sheet iron; • asbestos cement fibres (encapsulation); • also with direct application of waterproofing membrane. 2 Hopper capacity: lt. 200 approximately Versatile and portable. High productivity: up to 30 m3/h Preparation with cement mixer • granulometry 3-6 mm; • excellent also for the use in large mixing tank. 1. 2. 3. 4. 5. 6. 7. 8. 9. POLITERM BLU FEIN: water: as much as required for the mix (*) less 20-30 litres (point 7); Politerm Blu Ready Mix or Politerm Blu Fein Ready Mix; mix for about 10 minutes at maximum speed; sand if necessary (*) ; cement (*) ; mix for about 10 minutes at maximum speed; clean the loading bowl with about 20-30 litres of water (thus completing dosage of the mixing water); depending on the residual moisture in the sand (if any), add more water; on the way from the batch plant to the building site the cement mixer must turn at top speed for the first 20 minutes and then at minimum speed. COMPLEMENTARY PRODUCTS • granulometry 2 mm; • improved surface compactness. 2 PIANO ZERO SYSTEM RS MALTA L Throwaway PVC guide for the formation of level strips. Premixed antishrinkage smoothing mortar with very fast dehydration feature. To be used when making single-layer lightweight screeds. Profile height 5 cm The special cross-section design allows: • perfetct incorporation in the casting; • indeformability; • maintaining alignment; • preventing the formation of thermal bridges. 3 5 6 Equipment for sanding the surfaces of lightweight thermal insulating screeds. Synthetic latex to prepare adhesion bridges or improve the properties of cement mortars. Power supply voltage: 230V EDILSTIK BLOW MACHINE POLITAINER Latex spraying equipment (eg Edilstik FCA) Integrated logistics system for the delivery and the storage of the Politerm Blu range bags. Power supply voltage: 230V / 50Hz 7 ith red w prepa RM BLU s d e E re The sc ducts POLIT Therefore . o e the pr fectly stable ing surfac , y r n la e o l p ti a are ide sula re the und in they a type of so technical . y e ir for an ranting the ng the tim lo a ga s e c rman perfo To be used in execution of single-layer lightweight screeds (Piano Zero system): • to promote adhesion to the laying surface • for preparation of very thin smoothing mortars for surface protection. 10 Packaging: • bottles of 1 kg; • cans of 5 kg; cans of 20 kg. Palletised containers of 1000 kg 8 9 Edilstik can also be used: • as additive to the hydration water for traditional sand+cement screeds with anti shrinkage and/or adhesion improvement function; • to prepare grout or films for “fresh on fresh” application to improve adhesion on poorly absorbent surfaces for subsequent application of traditional sand+cement screeds or plasters. EDILSTIK FCA Pigmented synthetic latex for temporary inertisation of asbestos cement fibre sheets (certifi cate type “D”). To be applied before encapsulation work with lightweight thermal insulating mortars prepared with products of the Politerm Blu range. 11 �������� Packaging: • cans of 5 kg; cans of 20 kg. Palletised tanks of 1000 kg. Colour: yellow-orange Low-pressure application with spray nozzle (see Edilstik Blow Machine) or airless. * Mainly for partitional elements. Structural calculation is under responsability of the project engineer according to local regulations. Consult the technical data sheets and the application manuals Parquet and resilient flooring can be laid 24 hours after application. Ready mix self levelling smoothing mortar for thin-bed applications, ready to use, for manual as well as mechanical application. Screw for loading cement into the Politerm Machine tank Particularly suitable for surface finishing of single-layer lightweight thermal insulating screeds (Piano Zero system). Bags of 25 kg AUTOLIV EDILSTIK Make your job easier! • parquet (min. thickness Rs Malta L: 5 mm); • PVC, linoleum, rubber, carpeting (min thickness Rs Malta L: 20 mm). Electronic leveling tool with level display ELECTRICAL SANDERS Available types: • double-brush (2 discs) • single-brush (1 disc) To be used on single-layer lightweight screeds (Piano Zero system) for gluing of floor coverings as: LIVELLO PIANO ZERO POLITERM MACHINE SCREW Possibility of customised fittings. To obtain 1 m3 of finished mortar: 1. water (*) ; 2. first 420 lt. bag of Politerm Blu or Politerm Blu Fein; 3. cement (*) ; 4. second 420 lt. bag of Politerm Blu or Politerm Blu Fein; 5. continue mixing for 5 minutes; 6. pump. Preparation with truck-mixer Guides of 2 m each 4 Power supply voltage: 380V Preparation with Politerm Machine To obtain 200 lt of finished mortar: 1. water (*); 2. Politerm Blu or Politerm Blu Fein (1 bag of 170 lt); 3. cement (*); 4. sand (if necessary); 5. continue mixing for 5 minutes holding the bowl in an as horizontal as possible position; 6. pour the mortar. POLITERM BLU: > powered by: electric supply or hydraulic engine by means of power take-off (e.g.truck) > with or without the hopper for loading the mortar Productivity: up to 3 m /h 3 Superlight aggregates composed by virgin expanded polystyrene beads treated with the special E.I.A. additive for the preparation of lightweight and thermal insulating cement mixes. Politerm is used as thermally insulating and lightening material. Single-layer screeds Direct application of: • Ceramic, stoneware, clinker and prepolished marble floor coverings and laying of floating parquets; 5 • Parquets, after applying a thin-bed compound; 8 • Flexible flooring (carpet, pvc...), after application of thin-bed smoothing compound. 8 MIXING PREPARATION STEPS main indications *The dosages of the various components have to follow the prescriptions issued by Edilteco S.p.A. APPLICATIONS © Copyright EDILTECO S.p.A.- non-authorized copy is forbidden - Edilteco has the faculty to modify the products without previous notice. consultate schede tecniche e manuali di posa in opera High resistant levellings of cement screeds. It constitutes a support suitable for floor in PVC, carpet, laminated parquet, ceramic, epoxidic resins and polyurethane resins. Suitable for high resistance correction or levelling of screeds prepared with Politerm Blu or Isolcap, before the laying of ceramic tiles, porcelain stoneware, marble stoneware, natural stones and parquet. AUTOLIV M Self levelling screed. Autoliv M is a powder product for the preparation of cement-based self levelling screeds. For the application detached from the support: on top of polyethylene the application thickness of the product should be 30 mm, whilst on top of squeezable insulating materials is 40 mm. For the application in attachment to the support: application thickness from 20 mm. AUTOLIV SP Cement-based self-levelling screed. Autoliv SP is a powder product for the preparation of cement-based self-levelling screeds. The product can be applied in thicknesses varying from 4 to 8 cm. as a substitute of the traditional screed and to cover radiating underfloor heating systems. © Copyright EDILTECO S.p.A. – non-authorized copy is forbidden – Producer has the faculty to modify his products without previous notice. SPECIFIC EQUIPMENTS POLITERM MACHINE electrical power supply POLITERM MACHINE Diesel Pump-mixer for lightweight thermal insulating mortars based on: • polystyrene beads • cellular/foam concrete • perlite • cork Pump-mixer for lightweight thermal insulating mortars based on: • polystyrene beads • cellular/foam concrete • perlite • cork Pumping capacity up to 120 m distance and 30 m head (60 m with metal pipes) Pumping capacity up to 120 m distance and 30 m head (60 m with metal pipes) Power supply voltage: 380V Available with tank of: • 1 m3 Models: • ECO • H2O (automatic dosage of water) Available with tank of: • 1 m3 • 0,5 m3 High productivity: up to 10 m3/h Hydraulic control unit driven by a diesel engine homologated in compliance with the regulations regarding noise pollution. Possibility of customised fittings. High productivity: up to 10 m3/h PRODUCTS DESCRIPTION Building elements* • Blocks: 7 • Pre-casted wall 10 Intermediate layer - Filling • system levelling; 11 • under sand + cement screeds; 8 • under self-levelling screeds; 8 • under floor radiating heating (also with direct laying of the coils); 6 • vaulted floor levelling; 9 • under industrial flooring; • under driveable asphalt mantles; • in-between wall thermally insulating layer. 3 And also: • Gradient formation for terraces. 4 ISOLCAP MACHINE POLITERM PUMP Pump-mixer for: Pump for lightweight thermal insulating mortars based on: • polystyrene beads • cellular /foam concrete • perlite • cork • Lightweight mortars • Self-leveling mortars Weight: 128 kg. Tank capacity: approx. 260 lt. Power supply: electric with 6 kw 380/220 V Pumping maximum distance: approx. 50 mt. 1 Roofing • pitched roofs; 1 • flat roofs with or without gradient formation; • vaulted roofs; • corrugated sheet iron; • asbestos cement fibres (encapsulation); • also with direct application of waterproofing membrane. 2 Hopper capacity: lt. 200 approximately Versatile and portable. High productivity: up to 30 m3/h Preparation with cement mixer • granulometry 3-6 mm; • excellent also for the use in large mixing tank. 1. 2. 3. 4. 5. 6. 7. 8. 9. POLITERM BLU FEIN: water: as much as required for the mix (*) less 20-30 litres (point 7); Politerm Blu Ready Mix or Politerm Blu Fein Ready Mix; mix for about 10 minutes at maximum speed; sand if necessary (*) ; cement (*) ; mix for about 10 minutes at maximum speed; clean the loading bowl with about 20-30 litres of water (thus completing dosage of the mixing water); depending on the residual moisture in the sand (if any), add more water; on the way from the batch plant to the building site the cement mixer must turn at top speed for the first 20 minutes and then at minimum speed. COMPLEMENTARY PRODUCTS • granulometry 2 mm; • improved surface compactness. 2 PIANO ZERO SYSTEM RS MALTA L Throwaway PVC guide for the formation of level strips. Premixed antishrinkage smoothing mortar with very fast dehydration feature. To be used when making single-layer lightweight screeds. Profile height 5 cm The special cross-section design allows: • perfetct incorporation in the casting; • indeformability; • maintaining alignment; • preventing the formation of thermal bridges. 3 5 6 Equipment for sanding the surfaces of lightweight thermal insulating screeds. Synthetic latex to prepare adhesion bridges or improve the properties of cement mortars. Power supply voltage: 230V EDILSTIK BLOW MACHINE POLITAINER Latex spraying equipment (eg Edilstik FCA) Integrated logistics system for the delivery and the storage of the Politerm Blu range bags. Power supply voltage: 230V / 50Hz 7 ith red w prepa RM BLU s d e E re The sc ducts POLIT Therefore . o e the pr fectly stable ing surfac , y r n la e o l p ti a are ide sula re the und in they a type of so technical . y e ir for an ranting the ng the tim lo a ga s e c rman perfo To be used in execution of single-layer lightweight screeds (Piano Zero system): • to promote adhesion to the laying surface • for preparation of very thin smoothing mortars for surface protection. 10 Packaging: • bottles of 1 kg; • cans of 5 kg; cans of 20 kg. Palletised containers of 1000 kg 8 9 Edilstik can also be used: • as additive to the hydration water for traditional sand+cement screeds with anti shrinkage and/or adhesion improvement function; • to prepare grout or films for “fresh on fresh” application to improve adhesion on poorly absorbent surfaces for subsequent application of traditional sand+cement screeds or plasters. EDILSTIK FCA Pigmented synthetic latex for temporary inertisation of asbestos cement fibre sheets (certifi cate type “D”). To be applied before encapsulation work with lightweight thermal insulating mortars prepared with products of the Politerm Blu range. 11 �������� Packaging: • cans of 5 kg; cans of 20 kg. Palletised tanks of 1000 kg. Colour: yellow-orange Low-pressure application with spray nozzle (see Edilstik Blow Machine) or airless. * Mainly for partitional elements. Structural calculation is under responsability of the project engineer according to local regulations. Consult the technical data sheets and the application manuals Parquet and resilient flooring can be laid 24 hours after application. Ready mix self levelling smoothing mortar for thin-bed applications, ready to use, for manual as well as mechanical application. Screw for loading cement into the Politerm Machine tank Particularly suitable for surface finishing of single-layer lightweight thermal insulating screeds (Piano Zero system). Bags of 25 kg AUTOLIV EDILSTIK Make your job easier! • parquet (min. thickness Rs Malta L: 5 mm); • PVC, linoleum, rubber, carpeting (min thickness Rs Malta L: 20 mm). Electronic leveling tool with level display ELECTRICAL SANDERS Available types: • double-brush (2 discs) • single-brush (1 disc) To be used on single-layer lightweight screeds (Piano Zero system) for gluing of floor coverings as: LIVELLO PIANO ZERO POLITERM MACHINE SCREW Possibility of customised fittings. To obtain 1 m3 of finished mortar: 1. water (*) ; 2. first 420 lt. bag of Politerm Blu or Politerm Blu Fein; 3. cement (*) ; 4. second 420 lt. bag of Politerm Blu or Politerm Blu Fein; 5. continue mixing for 5 minutes; 6. pump. Preparation with truck-mixer Guides of 2 m each 4 Power supply voltage: 380V Preparation with Politerm Machine To obtain 200 lt of finished mortar: 1. water (*); 2. Politerm Blu or Politerm Blu Fein (1 bag of 170 lt); 3. cement (*); 4. sand (if necessary); 5. continue mixing for 5 minutes holding the bowl in an as horizontal as possible position; 6. pour the mortar. POLITERM BLU: > powered by: electric supply or hydraulic engine by means of power take-off (e.g.truck) > with or without the hopper for loading the mortar Productivity: up to 3 m /h 3 Superlight aggregates composed by virgin expanded polystyrene beads treated with the special E.I.A. additive for the preparation of lightweight and thermal insulating cement mixes. Politerm is used as thermally insulating and lightening material. Single-layer screeds Direct application of: • Ceramic, stoneware, clinker and prepolished marble floor coverings and laying of floating parquets; 5 • Parquets, after applying a thin-bed compound; 8 • Flexible flooring (carpet, pvc...), after application of thin-bed smoothing compound. 8 MIXING PREPARATION STEPS main indications *The dosages of the various components have to follow the prescriptions issued by Edilteco S.p.A. APPLICATIONS © Copyright EDILTECO S.p.A.- non-authorized copy is forbidden - Edilteco has the faculty to modify the products without previous notice. consultate schede tecniche e manuali di posa in opera High resistant levellings of cement screeds. It constitutes a support suitable for floor in PVC, carpet, laminated parquet, ceramic, epoxidic resins and polyurethane resins. Suitable for high resistance correction or levelling of screeds prepared with Politerm Blu or Isolcap, before the laying of ceramic tiles, porcelain stoneware, marble stoneware, natural stones and parquet. AUTOLIV M Self levelling screed. Autoliv M is a powder product for the preparation of cement-based self levelling screeds. For the application detached from the support: on top of polyethylene the application thickness of the product should be 30 mm, whilst on top of squeezable insulating materials is 40 mm. For the application in attachment to the support: application thickness from 20 mm. AUTOLIV SP Cement-based self-levelling screed. Autoliv SP is a powder product for the preparation of cement-based self-levelling screeds. The product can be applied in thicknesses varying from 4 to 8 cm. as a substitute of the traditional screed and to cover radiating underfloor heating systems. © Copyright EDILTECO S.p.A. – non-authorized copy is forbidden – Producer has the faculty to modify his products without previous notice. SPECIFIC EQUIPMENTS