Hydraulic Components Sistema Hidráulico

Hydraulic Components Sistema Hidráulico

Heavy Truck & Trailer Parts
Hydraulic Components
Sistema Hidráulico
DUMP PUMPS
C
GROUP
C Series
Miami, FL., U.S.A.
nsmission Selector Valves
KTC No.
REPLACE
DESCRIPTION
137-C101
C-101
Either shaft rotation
1" diameter keyed shaft
49 GPM (185.5 L / min ) Flow @
1.800 RPM
Max. RPM 2.400
KTC No.
REPLACE
DESCRIPTION
137-C102
C-102
Factory set rotation
7/8"-13 Tooth spliner shaft
49 GPM (185.5 L /min) Flow @
1.800 RPM
Max. RPM 2.400
Extended studs for support
bracket
All manufacturers names numbers, symbols and descriptions are references purposes only. And it is not implied any parts is that of these manufacturers. All efforts have been
made to ensure that the information contained here in is correct. KTC Group Equipment & Parts L.L.C can't be held responsible for its accuracy.
101-301
DUMP PUMPS
C
G Series
GROUP
KTC No.
REPLACE
DESCRIPTION
Miami, FL., U.S.A.
137-G101
nsmission
Selector Valves
G-101
• 3 piece cast iron design
• High pressure shaft seals
•Factory Set 2000 PSI relief with
load check
• Pressure balanced thrust plates
• Heavy duty roller bearings
• Two Or three line hook up
• Available with clockwise or
Counterclockwise shaft rotation
• 1 “ diameter shafts
•15 GPM (56.7 L / min) at 1000
RPM to 37 GPM (140 L / min) at
2400 RPM
KTC No.
REPLACE
DESCRIPTION
137-G102
G-102
• High pressure shaft seals
•Factory Set 2000 PSI relief with
load check
• Pressure balanced thrust plates
• Heavy duty roller bearings
• Two or three line hook up
• 7/8 “ 13 Tooth spline shaft
•15 GPM ( 56.7 L/min) at 1000
RPM to 37 GPM at 2400 RPM
All manufacturers names numbers, symbols and descriptions are references purposes only. And it is not implied any parts is that of these manufacturers. All efforts have been
made to ensure that the information contained here in is correct. KTC Group Equipment & Parts L.L.C can't be held responsible for its accuracy.
101-302
DUMP PUMPS
C
GROUP
Miami, FL., U.S.A.
KTC No.
REPLACE
DESCRIPTION
137- 2191748
219-1148
24 GPM (90.8 L/min)@ 1200 RPM, pressure
good for 2500 PSI
2 Shafts 1 1/8" dia for Bi-rotational use
Pad mount
1 1/2" NPT Inlet
3/4 O-ring outlet (1 1/16-12)
KTC No.
REPLACE
DESCRIPTION
137-P5151
P5151
•Dual Ported - Standard 1-1/2” NPT rear ports
and up to 1-1/2” NPT side ports
•Pressure balanced wear plates maintain high
pump efficiency throughout all operating
ranges
•Bi-Rotational Pump/Motor designed to fit a
wide variety of applications
•Doweled and high strength cast iron
construction
• High strength alloy steel gear and shaft sets
• Standard SAE “B” 2 & 4 Bolt mounting flange
• Standard SAE “B” Spline Output Shaft
•Cubic inch displacements from 4.50 through
7.07
• Working pressure up to 3000 PSI
• Speeds up to 3000 RPM
KTC No.
REPLACE
137- P21
P- 21
39 GPM (147 L/min)
• Porting, mounting, and shaft options available
DESCRIPTION
Pressure 3.000 PSI
All manufacturers names numbers, symbols and descriptions are references purposes only. And it is not implied any parts is that of these manufacturers. All efforts have been
made to ensure that the information contained here in is correct. KTC Group Equipment & Parts L.L.C can't be held responsible for its accuracy.
101-303
DUMP PUMPS
C
GROUP
Accesories
Miami, FL., U.S.A.
FIG.
1
2
3
4
REPLACE
PARKER ®
OEM
137-ASK-17
ASK-17 314-9414-017
ASK-20 308-9414-020
137-ASK-20
137-AV95
AV-95
137-329214X 329214X
KTC No.
APPLICATION
Air shift cylinder for C101 and C102
Air shift cylinder for G101 and G102
Pto. Control console
Pto. Control console
All manufacturers names (PARKER®), numbers, symbols and descriptions are references purposes only. And it is not implied any parts is that of these manufacturers. All efforts have
been made to ensure that the information contained here in is correct. KTC Group Equipment & Parts L.L.C can't be held responsible for its accuracy.
101-304