Procesos productivos
Transcripción
Procesos productivos
Boletín de novedades Marzo - Abril 2015 Sector Autopartes Innovaciones tecnológicas Procesos productivos Marzo - Abril 2015 Boletín de novedades Índice PUBLICACIONES CIENTÍFICAS Index-Report-FLAG Optimización del proceso de conformado en caliente utilizando técnicas de minería de datos... Dirección óptima de estampado para una pieza de automóvil Aserradura curva de componentes ligeros y delgados Investigación sobre soldadura láser disímil de láminas de acero de alta resistencia para l... Modelado de la cinética de transformación de fase para el proceso indirecto de estampado e... 2 2 3 4 5 PROYECTOS Materiales de li-ion resistente al envejecimiento para almacenamiento de energía en vehícu... 7 PATENTES Mecanismo diferencial para vehículo a motor Tanque de combustible para automóvil Conjunto de fijación para vehículo eléctrico y método Molde para correa de puerta de vehículo y método de fabricación del mismo Proceso y aparato para la fabricación de neumáticos para ruedas de vehículos 8 8 9 9 10 NOTICIAS Nuevo presidente de la Asociación de reciclaje de aluminio GDA Publirreportaje: Los centros de mecanizado Mazak dan la talla en todas las situaciones Toyota anunció recientemente la reanudación de su expansión con la construcción de dos nue... Cicloplast y la Universidad Nebrija impulsan la comunicación ambiental y gestión sostenibl... Wolf Robotics presenta nueva automatización de soldadura para NSRP Una nueva herramienta para mecánicos: Realidad aumentada Innovador sistema de medición 3D completamente automático para componentes soldados 11 11 12 12 13 13 14 NORMATIVAS TÉCNICAS ISO 10604:1993 - Vehículos de carretera – Equipo de medición para la orientación de los r... 15 Marzo - Abril 2015 Boletín de novedades Índice MERCADO Informe Industria Febrero 2015 En 2014, la facturación de componentes para automoción creció en torno a un 7% y se prevé... SERNAUTO da a conocer 28 iniciativas dirigidas a potenciar el sector de componentes 16 16 17 LEGISLACIÓN OJ:JOL_2015_087_R_0001: Reglamento n° 100 de la Comisión Económica de las Naciones Unidas ... 18 FINANCIAMIENTO Industria sumó a Impulso Argentino como incubadora 19 EVENTOS Automechanika Chicago 20 Pág. 2 Marzo - Abril 2015 Boletín de novedades Autopartes - Procesos Productivos PUBLICACIONES CIENTÍFICAS Optimización del proceso de conformado en caliente utilizando técnicas de minería de datos y método de elementos finitos Publicada el 31/03/2015 Abstract In the process of hot forming, many design variables have effects on the final results in different and complex ways, such as geometry feature and forming process parameters. It is difficult to understand the relationship between design variables and results, which is very important to guide the design. In this paper, Data Mining (DM) was introduced to explore the influence of the parts geometric feature and the hot forming parameters on hot forming results of an automobile B-pillar model, and the optimum parameter ranges were determined. Firstly, a series of variable parameters were chosen and 100 groups of experimental data were generated with super Latin method, then the FEM ananlysis results were calculated respectively. Secondly, analysis and evaluation of simulation results were carried out by making full use of the Decision Tree (DT) algorithm. Finally, a series of B-pillar hot forming rules were refined, such as the initial temperature of the sheet metal should be controlled between 720 °C to 800 °C. The fillet radius is recommended to be bigger than 10mm and the height gradient should be controlled under 67mm, etc. A real B-pillar model was designed to testify the rules and the result shows that the rules are correct and effective. ver más... Volver al índice Pág. 3 Marzo - Abril 2015 Boletín de novedades Autopartes - Procesos Productivos Dirección óptima de estampado para una pieza de automóvil Publicada el 02/02/2015 Abstract Stamping direction (SD) of an automotive part is investigated by using multi-objective optimization concerning forming process of sheet metal and validated by utilizing finite element (FE) method. To improve uniformity of feeding resistance and contact conditions (e.g., number and location of contact point) between tools and an automotive part, five mathematical models for optimization have been studied, and evaluation function of multi-objective optimization has been formulated by the sum-weighted method. The mathematical models presented are solved effectively by using the adaptive genetic algorithm (GA), and tipping angles of the automotive part are different from those determined by AutoForm system. Solutions of SD are global optima. The computational programs are highly efficient and stable. The optimal SD obtained has been validated by FE method. Comparing the adaptive GA with the other three methods determined in AutoForm, we find that the stamped part using the adaptive GA has a good forming quality and with the biggest deforming ample degree value (11.3 %). For the feasible regions of blank-holder force and friction coefficient, the results indicate that the adaptive GA characterizes a biggest limit in the four tipping angles, which has been supported experimentally. Methods of SD presented are helpful for quickly getting a compromise among process parameters of an automotive part. ver más... Volver al índice Pág. 4 Marzo - Abril 2015 Boletín de novedades Autopartes - Procesos Productivos Aserradura curva de componentes ligeros y delgados Publicada el 31/01/2015 Abstract Increasing application of carbon fibre reinforced plastic (CFRP) in lightweight constructions in aerospace, automotive and other industries requires high-performance cutting processes for edge trimming of thin shell structures. As an alternative to conventional processes, e.g. milling, a rigid abrasive circular saw blade is introduced. The limitation of cutting only almost-straight contours with circular saw blades is overcome by a novel tool geometry and process kinematic that allows curve cutting with radius \(R < 500\) mm on thin plane material (thickness \(t<10\) mm). The kinematic for cutting almost arbitrarily shaped outlines with a circular tool on a five-axis machine is described and proven by cutting a reference component. Besides high operating efficiency because of high feed rate the process features sound edge quality without noteworthy delamination of the outer layers, which is shown in pilot tests on CFRP with unidirectional top layers. ver más... Volver al índice Pág. 5 Marzo - Abril 2015 Boletín de novedades Autopartes - Procesos Productivos Investigación sobre soldadura láser disímil de láminas de acero de alta resistencia para la industria automotriz Publicada el 23/01/2015 Publication date: 23 January 2015. Source: Materials Science and Engineering: A. Author(s): M. Rossini , P. Russo Spena , L. Cortese , P. Matteis , D. Firrao. To support the use of advanced high strength steels in car body design and fabrication, an investigation was carried out on dissimilar butt laser welding between a couple of the following metals: TWinning Induced Plasticity (TWIP) steels, Dual Phase (DP) steels, hot stamping boron (22MnB5) steels, and TRansformation Induced Plasticity (TRIP) steels. The base materials and the weldments were fully characterized by means of metallography, microhardness, and tensile tests. Digital image analysis was also used to provide additional information on the mechanical behavior of the joints, in terms of local strain field with load during the tensile tests. Fractographic examination was finally performed on the fracture surfaces of the tensile samples. The dissimilar joints between the DP, 22MnB5, and TRIP steels exhibit good resistance properties. On the contrary, the dissimilar joints encompassing the TWIP steel exhibit poor mechanical strength and fail along the weld seam by intergranular fracture probably due to presence of Mn segregations. Therefore, the laser welding of TWIP steel with other advanced high strength steels is not recommended without the use of proper metal fillers. Dissimilar laser welding of DP, TRIP and 22MnB5 combinations can be a solution to assemble car body parts made of these steel grades. ver más... Volver al índice Pág. 6 Marzo - Abril 2015 Boletín de novedades Autopartes - Procesos Productivos Modelado de la cinética de transformación de fase para el proceso indirecto de estampado en caliente con foco en las piezas de carrocería con propiedades a medida Publicada el 19/01/2015 Publication date: 19 January 2015. Source: Journal of Materials Processing Technology.Author(s): Paul Hippchen , Arnulf Lipp , Hannes Grass , Philipp Craighero , Michael Fleischer , Marion Merklein. To design the indirect hot stamping process, a Finite Element Method (FEM) based prediction of the part geometry and the mechanical properties is required. In case of indirect hot stamping processes, producing car body parts with tailored properties, cooling paths occur causing diffusionless and diffusion controlled phase transformations. The volume expansion caused by the phase transformation of face-centred cubic (fcc) into body-centred cubic (bcc) and the martensitic formation of body-centered tetragonal (bct) leads to transformation induced strains that are important for the calculation of overall stresses in hot stamped car body parts. To calculate the strain and stress state correctly, it is necessary to model the diffusionless and diffusion controlled phase transformation phenomena, taking into account the boundary conditions of indirect hot stamping processes. The existing material models are analysed and extended in order to improve their prediction accuracy in calculating the amount and distribution of ferrite, perlite, bainite and martensite during the whole process of annealing. For industrial use the new approaches are implemented in the FE-code LSDYNA 971 (Livermore Software Technology Corporation, 2006). ver más... Volver al índice Pág. 7 Marzo - Abril 2015 Boletín de novedades Autopartes - Procesos Productivos PROYECTOS Materiales de li-ion resistente al envejecimiento para almacenamiento de energía en vehículos eléctricos Publicada el 13/04/2015 MARS-EV aims to overcome the ageing phenomenon in Li-ion cells by focusing on the development of highenergy electrode materials (250 Wh/kg at cell level) via sustainable scaled-up synthesis and safe electrolyte systems with improved cycle life (> 3000 cycles at 100%DOD). Through industrial prototype cell assembly and testing coupled with modelling MARS-EV will improve the understanding of the ageing behaviour at the electrode and system levels. ver más... Volver al índice Pág. 8 Marzo - Abril 2015 Boletín de novedades Autopartes - Procesos Productivos PATENTES Mecanismo diferencial para vehículo a motor Publicada el 08/04/2015 A motor vehicle differential gear has at least one housing part as a first gear part, and a crown wheel as a second gear part. The first and second gear parts are connected via respective first connection surfaces running in the axial direction by a press fit, and via respective second connection surfaces running at an angle to the axial direction, forming a welding seam. One of the gear parts is formed from a steel and the other gear part from a cast iron material, as well as such a differential gear in which the second connection surfaces connect directly to the first connection surfaces. ver más... Tanque de combustible para automóvil Publicada el 01/04/2015 In an automobile fuel tank with a tank body (12) of which an outer wall (19) is formed from a synthetic resin layer comprising a multilayer configuration, the synthetic resin layer includes an inner body layer and an outer body layer with an interposed barrier layer (26). The outer wall (19) includes an upper skin layer (20), an outer base layer (22), an outer adhesive layer (24), a barrier layer (26), an inner adhesive layer (28), an inner base layer (30), and a structural member (32), which are formed successively from an outer side toward an inner side. The structural member (32) is retrofitted to the inner base layer (30) by welding during formation of the inner body layer and the outer body layer. ver más... Volver al índice Pág. 9 Marzo - Abril 2015 Boletín de novedades Autopartes - Procesos Productivos Conjunto de fijación para vehículo eléctrico y método Publicada el 25/03/2015 An example method of connecting an electric vehicle battery includes welding a landing of a terminal to a bus bar, and pressing a landing of the terminal and the bus bar against one another during the welding. The landing is along a first plane and a base of the terminal is along a second plane that is spaced from the first plane. ver más... Molde para correa de puerta de vehículo y método de fabricación del mismo Publicada el 07/01/2015 The present invention provides a method for manufacturing the doorbelt molding including: forming an anodized layer on a surface of an aluminum alloy plate by performing an anodizing treatment on the aluminum alloy plate; forming a clear coating layer on the anodized layer by performing a clear coating treatment on the aluminum alloy plate on which the anodized layer is formed; molding a sectional shape of an outer frame by roll-forming the aluminum alloy plate over which the anodized layer and the clear coating layer are formed; forming a molding intermediate member in which the outer frame and an inner molding are integrally formed by integrally injection-molding a synthetic resin into the outer frame formed by the rollforming, wherein the synthetic resin is a material of the inner molding; bending and cutting the molding intermediate member to manufacture the doorbelt molding. ver más... Volver al índice Pág. 10 Marzo - Abril 2015 Boletín de novedades Autopartes - Procesos Productivos Proceso y aparato para la fabricación de neumáticos para ruedas de vehículos Publicada el 24/12/2014 Building the carcass structure of tyres for vehicle wheels includes associating, at each end edge of a carcass ply, at least one respective annular reinforcement structure formed by depositing along a circumferential direction a plurality of reinforcement elements having a first length. Such elements are cut to size from a reinforced continuous bandlike element fed to a cutting group arranged at a first operative position adapted to allow a barycentric grip of the reinforcement elements. The cutting group can translate along a feeding direction of the band-like element to a second operative position for cutting to size a plurality of second reinforcement elements having a second length different from the first length. The second operative position is defined on the basis of the second length, so as to have a barycentric grip of the second reinforcement elements too. ver más... Volver al índice Pág. 11 Marzo - Abril 2015 Boletín de novedades Autopartes - Procesos Productivos NOTICIAS Nuevo presidente de la Asociación de reciclaje de aluminio GDA Publicada el 15/04/2015 Thomas Reuther, Mitglied des Vorstands der Trimet Aluminium, ist neuer Vorsitzender des Fachverband Aluminiumrecycling im GDAGesamtverband der Aluminiumindustrie. ver más... Publirreportaje: Los centros de mecanizado Mazak dan la talla en todas las situaciones Publicada el 15/04/2015 Entre su amplia gama de centros de mecanizado Mazak destaca el modelo de 5 ejes Variaxis i-700 - Matrix 2, un modelo de altas prestaciones, diseñado con una robustez extraordinaria para proporcionar las más altas precisiones y las mayores velocidades de trabajo, conseguidas solamente a base de emplear las más modernas tecnologías tanto en fabricación mecánica como en equipos electrónicos de control. Tiene una gran capacidad de mecanizado de diámetro 850 x500 mm, gracias al cabezal de 12.000/18.000 rpm y sus 60.000 mm/min (2362 IPM). ver más... Volver al índice Pág. 12 Marzo - Abril 2015 Boletín de novedades Autopartes - Procesos Productivos Toyota anunció recientemente la reanudación de su expansión con la construcción de dos nuevas plantas en China y México Publicada el 15/04/2015 Toyota a récemment annoncé la reprise de son expansion avec les construction de deux nouvelles usines, en Chine et au Mexique. S’agissant de l’usine mexicaine, l’investissement porterait sur 1 milliard de dollars. L’usine serait située dans l’Etat de Guanajuato au centre du Mexique et devrait produire 200 000 voitures par an. Elle permettrait par ailleurs la création d’environ 2 400 emplois directs. Des informations publiées récemment dans la presse indiquaient que le site assemblerait à partir de l’été 2019 des Corolla destinées au marché nord-américain. ver más... Cicloplast y la Universidad Nebrija impulsan la comunicación ambiental y gestión sostenible de los plásticos Publicada el 15/04/2015 Cicloplast y la Universidad Nebrija organizan la V Jornada de Periodismo Ambiental y Gestión Sostenible de Plásticos. El acto se celebrará el 9 de abril en la Fundación Antonio Nebrija e intervendrán periodistas, profesores y expertos en medio ambiente y desarrollo sostenible. ver más... Volver al índice Pág. 13 Marzo - Abril 2015 Boletín de novedades Autopartes - Procesos Productivos Wolf Robotics presenta nueva automatización de soldadura para NSRP Publicada el 16/02/2015 The National Shipbuilding Research Program (NSRP), is defined as a collaboration of U.S. shipyards working together to reduce the cost of building, operating and repairing Navy ships by improving productivity and quality through advanced technology and processes. Though founded in 1971, NSRP’s goal has remained the same. ver más... Una nueva herramienta para mecánicos: Realidad aumentada Publicada el 10/02/2015 Continental’s Connected Technician uses a tablet with a wireless link to a vehicle to coach a mechanic step-by-step through the entire process of diagnosing a problem and then fixing it. The device will be on the market next year. ver más... Volver al índice Pág. 14 Marzo - Abril 2015 Boletín de novedades Autopartes - Procesos Productivos Innovador sistema de medición 3D completamente automático para componentes soldados Publicada el 02/02/2015 Los componentes soldados para los sistemas de escape de vehículos deben cumplir estrictos requisitos en cuanto a la precisión dimensional y la estanqueidad del gas. La garantía de calidad en este campo es importante y a menudo conlleva mucho tiempo. ver más... Volver al índice Pág. 15 Marzo - Abril 2015 Boletín de novedades Autopartes - Procesos Productivos NORMATIVAS TÉCNICAS ISO 10604:1993 - Vehículos de carretera – Equipo de medición para la orientación de los rayos luminosos del faro delantero Publicada el 14/04/2015 This document reached stage 90.20 on 2015-04-15 , TC/SC: ISO/TC 22/SC 35, ICS: 43.180 ver más... Volver al índice Pág. 16 Marzo - Abril 2015 Boletín de novedades Autopartes - Procesos Productivos MERCADO Informe Industria Febrero 2015 Publicada el 04/03/2015 La producción nacional de vehículos fue de 45.605 unidades y registró en febrero un aumento de 78 % respecto de enero y una baja de 13,9 % con relación a igual mes del año pasado. Las exportaciones se ubicaron en 24.223 unidades y tuvieron un crecimiento de 217,9 % con relación enero y baja de 6,8 % con relación a febrero 2014. ver más... En 2014, la facturación de componentes para automoción creció en torno a un 7% y se prevé que pueda alcanzar el 8% este año Publicada el 09/02/2015 Según las primeras estimaciones realizadas por la Junta Directiva de la Asociación Española de Fabricantes de Equipos y Componentes para Automoción, SERNAUTO, el sector obtuvo en 2014 un incremento de la facturación de entre 6-7%. Además, el empleo en el sector creció entre 10.000 y 12.000 puestos de trabajo con respecto al año anterior. Entre las previsiones para 2015, las empresas asociadas a SERNAUTO consideran que la facturación puede crecer en torno a un 7-8% con respecto a 2014, con la consiguiente generación de empleo. ver más... Volver al índice Pág. 17 Marzo - Abril 2015 Boletín de novedades Autopartes - Procesos Productivos SERNAUTO da a conocer 28 iniciativas dirigidas a potenciar el sector de componentes Publicada el 09/12/2014 SERNAUTO presentó el 28 noviembre la "Agenda Estratégica Componentes 2020" con el objetivo de potenciar la industria en los próximos años. José María Pujol, presidente de SERNAUTO, ha explicado que "desde las empresas que forman parte de SERNAUTO, nos dimos cuenta que necesitábamos reflexionar sobre como queríamos que fuera nuestra industria en el futuro, en un momento clave en el que el Ministerio de Industria quiere llevar a cabo - con el resto de la Administración reformas de calado para contribuir al fortalecimiento de la industria". ver más... Volver al índice Pág. 18 Marzo - Abril 2015 Boletín de novedades Autopartes - Procesos Productivos LEGISLACIÓN OJ:JOL_2015_087_R_0001: Reglamento n° 100 de la Comisión Económica de las Naciones Unidas para Europa (CEPE/ONU) — Disposiciones uniformes relativas a la homologación de vehículos en relación con los requisitos específicos del grupo motopropulsor eléctrico [2015/505] Publicada el 30/03/2015 Regulation No 100 of the Economic Commission for Europe of the United Nations (UNECE) — Uniform provisions concerning the approval of vehicles with regard to specific requirements for the electric power train [2015/505] ver más... Volver al índice Pág. 19 Marzo - Abril 2015 Boletín de novedades Autopartes - Procesos Productivos FINANCIAMIENTO Industria sumó a Impulso Argentino como incubadora Publicada el 13/03/2015 El secretario PyME del Ministerio de Industria, Horacio Roura, firmó hoy el convenio por el cual el fondo de capital social Impulso Argentino quedó formalmente operativo para actuar como Institución Especializada en Apoyo Emprendedor (Incubadora), dentro del programa Incubar de la cartera que conduce Débora Giorgi. ver más... Volver al índice Pág. 20 Marzo - Abril 2015 Boletín de novedades Autopartes - Procesos Productivos EVENTOS Automechanika Chicago Publicada el 06/04/2015 April 24-26, 2015. Chicago, USA. Automechanika Chicago is the largest tradeshow and training event for the Automotive Aftermarket industry. Designed specifically for automotive service and collision repair shop owners, technicians, distributors, jobbers, and more, Automechanika Chicago is focused on high-end technical and management training while showcasing the newest tools, equipment, and products in the market. ver más... Volver al índice Para más información: Programa Nacional de Vigilancia Tecnológica e Inteligencia Competitiva · VINTEC Dirección Nacional de Estudios (DNE) · Subsecretaría de Estudios y Prospectiva Ministerio de Ciencia, Tecnología e Innovación Productiva de la Nación Godoy Cruz 2320 3 piso (entre Guatemala y Paraguay) · (C1425FQD) · Buenos Aires · Argentina Tel: 4899-5300 int. 3004 · [email protected] · www.mincyt.gob.ar Entidades que colaboraron: Trabajo realizado por: