kwik clean3 - Strahman Valves
Transcripción
kwik clean3 - Strahman Valves
Additional Pre-Rinse Products Available: The Pivot Pro™ swivel connector, installed between the handle and hose, allows for greater cleaning flexibility and better ergonomic performance for the washer. Nut Driver/Tip Changer for replacing tips Replacement tips: all tips are easily removable, cleanable or changeable to offer the best performance for each customer’s specific requirements. Pivot Pro™ swivel connector Nut Driver/ Tip Changer Available tips are: Flat V spray fan tips with angles of 5 degrees, 10, 15, 20…up to 110 degrees. Solid-stream, jet spray tips. Tri-Tip for fast cleaning with splash control. Flow rates from 0.3 gpm to over 2.0 gpm. Full cones, hollow cones or tips with an angle built into the tip itself. Fan Spray, Solid Stream, Tri-Tip (top to bottom) Last Updated: August, 2011 USA Headquarters 2801 Baglyos Circle Bethlehem, PA 18020 Phone: (484) 893-5080 Fax: (484) 893-5099 Toll Free: (877) STRAHMAN [email protected] www.strahmanvalves.com QCD09.005A ISO 9001 Management System Registered KWIK CLEAN 3 Instructions for Assembly ® Instructions to assemble KWIK CLEAN 3® pre-rinse equipment: 1. Shut off the water supply. 2. If you are replacing the hose, loosen the hose from the top of the riser by turning the hose in a counter-clockwise direction. 3. If you are replacing an existing handle, loosen the handle from the hose by turning the handle in a counter-clockwise direction. 3/4-14 UNS-2A MALE THREAD 5/16" LONG 4. Install the larger washer between the handle and the hose, and turn the handle into the hose in a clockwise direction until hand tight. WASHER SUPPLIED WITH HANDLE (SMALL WASHER) 5. If you are replacing a pre-rinse nozzle, hold the handle firmly and turn the existing nozzle in a counter-clockwise direction to remove. 6. Install the smaller washer between the handle and the Kwik Clean 3® nozzle and tighten by turning the nozzle in a clockwise direction. 7. Slowly turn the water back on, check for leaks and tighten further if necessary. 3/4-14 UNS-2B FEMALE THREAD 7/8-20 UNEF-2A MALE THREAD WASHER SUPPLIED WITH HANDLE (LARGE WASHER) Kwik Clean 3® Pre-Rinse Nozzle Pre-Rinse Handle SPRAY RINSE HOSE AVAILABE LENGTHS 7/8-20 UNEF-2B FEMALE THREAD TYPICAL BOTH ENDS This end attaches to the top of the riser STANDARD 36” AND 44” WASHERS SUPPLIED WITH SPRAY RINSE HOSE (LARGE WASHER) - ORIGINAL REV DESCRIPTION 2801 Bagylos Circle Bethlehem, Pa. 18020 USA Tel: 01 (1) 484-893-5080 Fax: 01 (1) 484-893-5099 WWW.STRAHMANVALVES.COM UNLESS OTHERWISE NOTED 1. ASME Y14.5M-1994 APPLIES. 2. TOLERANCES ARE: 1/64 FRACTIONS .005 3 PLACE DECIMALS .01 2 PLACE DECIMALS 0 30' ANGLES 3. INTERNAL CORNER RAD. .020 MAX. 4. ALL DIMENSIONS ARE IN INCHES. 5. ALL MACHINED SURFACES SHALL HAVE FINISH OF 63 RMS MAX. 6. REMOVE ALL BURRS AND BREAK SHARP EDGES .015 MAX. SPRAY RINSE HOSE, HANDLE AND KWIK CL SCALE SIZE 1:2 B ASSEMBLY WEIGHT lb DRAW 2102 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF STRAHMAN VALVES. ANY REPRODUCTION IN PART OR AS A WHOLEWITHOUT THE WRITTEN PERMISSION OF STRAHMAN VALVES IS PROHIB Additional Pre-Rinse Products Available: The Pivot Pro™ swivel connector, installed between the handle and hose, allows for greater cleaning flexibility and better ergonomic performance for the washer. Nut Driver/Tip Changer for replacing tips Replacement tips: all tips are easily removable, cleanable or changeable to offer the best performance for each customer’s specific requirements. Pivot Pro™ swivel connector Nut Driver/ Tip Changer Available tips are: Flat V spray fan tips with angles of 5 degrees, 10, 15, 20…up to 110 degrees. Solid-stream, jet spray tips. Tri-Tip for fast cleaning with splash control. Flow rates from 0.3 gpm to over 2.0 gpm. Full cones, hollow cones or tips with an angle built into the tip itself. Fan Spray, Solid Stream, Tri-Tip (top to bottom) Last Updated: August, 2011 USA Headquarters 2801 Baglyos Circle Bethlehem, PA 18020 Phone: (484) 893-5080 Fax: (484) 893-5099 Toll Free: (877) STRAHMAN [email protected] www.strahmanvalves.com QCD09.005A ISO 9001 Management System Registered KWIK CLEAN 3 Instructions for Assembly ®