neo blinder mkii
Transcripción
neo blinder mkii
NEO BLINDER MKII USER MANUAL / MANUAL DE USUARIO PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE USE POR FAVOR LEA LAS INSTRUCCIÓNES ANTES DE USAR For your own safety, please read this user manual careful- vice is never exposed to the direct smoke jet and is in- ly before you initially start-up. stalled in a distance of 0.5 meters between smoke ma- SAFETY WARNING chine and device. • The ambient temperature must always be between -15° C and +45° C. Keep away from direct insulation (particularly in cars) and heaters. • Never use the device during thunderstorms. Over voltage could destroy the device. Always disconnect the de- • All maintenance must be carried out by a qualified electrician. • vice during thunderstorms. • The device must only be installed on a non-flamma- A minimum distance of 0.5m must be maintained between ble surface. In order to safeguard sufficient ventilation, the equipment and a combustible surface. leave 50 cm of free space around the device. • The product must always be operated in a well ventilated area. • DO NOT stare directly into the light source. fix the fixture with an appropriate safety-rope. Fix the • Always disconnect the power before carrying out any safety-rope at the correct fixation points only. The safe- maintenance. ty-rope must never be fixed at the transport handles! • The earth must always be connected to the ground. • Ensure that all parts of the equipment are kept clean and free of dust. • • and maintenance of this device has to be qualified. • Follow the instructions of this manual. • Consider this manual to be part of the total product. • Keep this manual for the entire service life of the product. • Pass this manual on to every further owner or user of Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened. • Operate the device only after having become familiarized with its functions. Do not permit operation by persons IMPORTANT Every person involved with the installation, operation For overhead use (mounting height >100 cm), always not qualified for operating the device. Most damages are the result of unprofessional operation! • Please consider that unauthorized modifications on the device are forbidden due to safety reasons! • Never remove the serial barcode from the device as this would make the guarantee void. the product • Download the latest version of the user manual from the Internet. OPERATING DETERMINATIONS • This product is only allowed to be operated with an alternating voltage of 100-240 V, 50/60 Hz. • This device is designed for professional use, e.g. on stages, in clubs, bars, theatres etc. • Do not shake the device. Avoid brute force when installing or operating the device. • When choosing the installation-spot, please make sure that the device is not exposed to extreme heat, moisture or dust. There should not be any cables lying around. Please make sure that the unit cannot be touched or bumped. • When using smoke machines, make sure that the de- NEO BLINDER MKII ENGLISH VERSION p. 2 NEO BLINDER MKII High-performance professional blinder – 4 x 100W COB LEDs Neo Blinder MKII is a LED professional blinder for outdoor use powered by 4 x 100W White COB LEDs. Thanks to its chip-onboard technology it reaches an amazing power and coverage. Its 4 outputs have independent focus regulation and can be controlled separately thanks to its pixel by pixel technology. Ideal for big scenarios, Neo Blinder MKII is the nowadays response to the classic blinder application, adding a soft dimming and strobe effects that make it stand out naturally apart from an ideal power/consumption relation. DMX connectors: 2 outdoor XLR connectors (XLR-3 input and output) PowerCON® power supply connectors Dimensions: 362x163x362 mm. / 14.2x6.4x14.2 in. Weight: 8.7 Kg. / 19 Lbs. Source & Optics Light source: 4 x 100W Warm White COB LEDs LEDs life: 50,000 hours Beam angle: 49º Field Angle: 79º Photometric data Luminous flux: 640 Lux @ 5m (16 ft) Color temperature: 3100K Effects and functions Professional blinder Pixel by pixel control Manual directional adjustment for every integrated projector COB LED technology: More power output with less heat generation Dimmer: 0-100% with 4 different modes Strobe effect: 0-30Hz Flicker free operation Control DMX Channels: 1/3/4/9 Operational modes: DMX, Master/Slave, Static and Built-in programs DMX software update (optional) Advanced RDM function Electrical Input voltage range: AC100–240V, 50-60Hz Power consumption: 300W Physical IP Rating: IP20 LCD display NEO BLINDER MKII ENGLISH VERSION p. 3 DMX Chart for NEO BLINDER MKII 1-CH Function Value Percent/Setting 1 Dimmer 000-255 0~100% 3CH Function Value Percent/Setting 1 Dimmer-H 000-255 0~100% 2 Dimmer-L 000-255 0~100% 000-010 No Function 011-132 Strobe slow to fast(All pods) 3 Strobe 133-255 Value Percent/Setting 1 White1 000-255 0~100% 2 White2 000-255 0~100% 3 White3 000-255 0~100% 4 White4 000-255 0~100% 15CH Function Value Percent/Setting 1 Dimmer-H 000-255 0~100% 2 Dimmer-L 000-255 0~100% 000-010 No Function 011-132 133-255 0~100% 5 White1-L 000-255 0~100% White1- 000-010 No Function Strobe 011-255 Strobe slow to fast 7 White2-H 000-255 0~100% 8 White2-L 000-255 0~100% White2- 000-010 No Function Strobe 011-255 Strobe slow to fast 10 White3-H 000-255 0~100% 11 White3-L 000-255 0~100% White3- 000-010 No Function Strobe 011-255 Strobe slow to fast 13 White4-H 000-255 0~100% 14 White4-L 000-255 0~100% White4- 000-010 No Function Strobe 011-255 Strobe slow to fast 15 NEO BLINDER MKII ENGLISH VERSION 16 Bit strobe macros) 000-255 12 Remark Strobe Slow to Fast(All pods) White1-H 9 Remark Strobe Slow to Fast (Random 4 6 16Bit strobe macros) Function Strobe Remark Strobe slow to fast (Random 4CH 3 Remark 16 Bit 16 Bit 16 Bit 16 Bit p. 4 Menu for NEO BLINDER MKII NO. 1 2 Main Menu Auto Show Static Menu level 2 Menu level Menu 3 level4 Remark Auto Show Speed <Auto 1> <100> <Auto 2> <100> <Auto 3> <100> <Auto 4> <100> <Auto 5> <100> <Auto 6> <100> <Dimmer> <255> Default: Dim- <Strobe> <0> mer=255;Strobe=0 Default: Auto 1;Speed:100 <Off> 3 Dimmer <Dimmer 1> Mode <Dimmer 2> Default: 0FF <Dimmer 3> <On> 5 Back Light <10S> Default: On <20S> <30S> 6 7 Information DMX Address Auto <Test> Fixture Hours <9999> Version <V1.0> 1 Default: 001 <1Ch> 8 DMX Chan- <3Ch> nel <4Ch> Default: 15CH <15Ch> 9 10 Master/ <Master> Slave <Slave> Fan Mode <Auto> Default:Slave 40ºC <High> <LED1:40ºC> 11 Tempera- <LED2:40ºC> ture <LED3º40C> <LED4º40C> 600Hz 12 LED Frequency 1200 Hz 2000 Hz Default: 1200HZ 4000 Hz 25KHz NEO BLINDER MKII ENGLISH VERSION p. 5 NEO BLINDER MKII - Parameter table NEO BLINDER MKII ENGLISH VERSION p. 6 Por su propia seguridad, por favor lea atentamente el • Al usar máquinas de humo, asegúrese de que el dispositivo no está expuesto al chorro de directo de la máqui- manual antes de utilizar el equipo. na y de que sea instalado a una distancia mínima de 0,5 ADVERTENCIA DE SEGURIDAD metros entre la máquina de humo y el dispositivo. • La temperatura ambiente debe estar siempre entre -15 ° C y + 45 ° C. Mantener alejado del sol directo (especialmente en el coche) y calentadores. • • • • Nunca utilice este dispositivo durante tormentas eléctri- Este producto debe ser instalado por un profesional cas. El Sobre-voltaje podría destruir el dispositivo. Siem- calificado. pre desconecte el aparato durante tormentas eléctricas. Toda mantención debe ser llevada a cabo por un electr- • El equipo sólo se debe instalar sobre una superficie no icista calificado. inflamable. Con el fin de salvaguardar la ventilación sufi- Una distancia mínima de 0.5m debe ser mantenida entre ciente, deje 50 cm de espacio libre alrededor del aparato. el equipo y cualquier superficie combustible. • Por instalar el equipo encima de la cabeza (altura de • El producto debe ser siempre operado en áreas ventiladas. montaje> 100 cm), siempre fije el aparato con una cuer- • NO mire de forma directa hacia la fuente de luz. da de seguridad apropiada. Fijar la cuerda de seguridad • Siempre desconecte el equipo antes de realizar cualqui- sólo en los puntos de fijación correctos. La seguridad de er tipo de mantención. la cuerda no debe fijarse en las asas de transporte. • El neutro debe estar siempre conectado a tierra. • Asegúrese que todas las partes del equipo se mantengan que el recinto del mismo está bien cerrado y con todos limpias y libres de polvo. los tornillos bien apretados. IMPORTANTE • • • Opere el equipo solamente luego de haber comprobado Haga funcionar el aparato sólo después de familiarizarse con sus funciones. No permitir la utilización por parte de personas no calificadas para operar el dispositivo. La Toda persona involucrada con las instalación, operación mayoría de los daños son el resultado de una operación y mantenimiento del equipamiento debe estar califica- poco profesional. da para ello. • Seguir las instrucciones de este manual. • Considerar este manual parte del producto. • Mantener este manual durante toda la vida útil del producto. • Pasar el presente manual a cada uno de los futuros • Por favor, considere que las modificaciones no autorizadas del aparato están prohibidas por razones de seguridad. • Nunca quite el código de barras de serie del dispositivo ya que esto haría que la garantía pierda vigencia. dueños de la unidad. • Descargar la última versión disponible del sitio de internet de la empresa. DETERMINACIONES DE OPERACIÓN • Este producto solamente puede ser operado en un voltaje de 100-240 V, 50/60 Hz. • Este equipamiento está diseñado para uso profesional. Por ejemplo: escenarios, clubs, bares y teatros. • No agite el equipo. Evite la fuerza bruta al instalar o hacer funcionar el dispositivo. • Al elegir el lugar de la instalación, por favor asegúrese de que el dispositivo no está expuesto a calor extremo, humedad o polvo. No debe haber ningún cable por ahí. Por favor, asegúrese de que la unidad no puede ser tocada ni golpeada. NEO BLINDER MKII VERSIÓN ESPAÑOL p. 7 NEO BLINDER MKII Blinder profesional de alto desempeño – 4 LEDs COB de 100W Físico Certificación IP20 Pantalla LCD Neo Blinder MKII es un blinder LED profesional para uso ex- Conectores DMX: 2 conectores XLR de exteriores (XLR-3 en- terior que tiene 4 LEDs COB blancos cálidos de 100W. Gracias trada y salida) a su tecnología chip-on-board brinda una potencia y una Conectores de alimentación powerCON® cobertura sin precedentes. Sus 4 salidas cuentan con regu- Dimensiones: 362x163x362 mm. / 14.2x6.4x14.2 in. lación de foco independiente y pueden ser controlados de Peso: 8.7 Kg. / 19 Lbs. manera separada, gracias a su tecnología pixel por pixel. Ideal para grandes escenarios, Neo Blinder MKII es la respuesta actual a la clásica aplicación de blinders, agregando un dimming suave, efectos de estrobo que lo hacen destacarse naturalmente y una relación potencia/consumo ideal. Fuente & Ópticas Fuente de luz: 4 LEDs COB blancos cálidos de 100W Vida útil promedio: 50.000 horas Ángulo de haz: 49º Ángulo de campo: 79º Datos fotométricos Flujo lumínico: 640 Lux @ 5m (16 ft) Temperatura color: 3100K Efectos y funciones Blinder profesional Control pixel por pixel Ajuste manual del direccionamiento de cada proyector integrado Tecnología LED COB: Mayor potencia con menor generación de calor Dimmer: 0-100% con 4 modos diferentes Efecto estrobo: 0-30Hz Opción para operación sin parpadeo Control Canales DMX: 1/3/4/9 Modos de operación: DMX, Master/Slave, programas integrados & estático Actualización de software vía DMX (opcional) Función RDM avanzada Eléctrico Rango de voltaje de entrada: AC100–240V, 50-60Hz Consumo de potencia: 300W NEO BLINDER MKII VERSIÓN ESPAÑOL p. 8 DMX Chart para el NEO BLINDER MKII 1-CH Function Value Percent/Setting 1 Dimmer 000-255 0~100% 3CH Function Value Percent/Setting 1 Dimmer-H 000-255 0~100% 2 Dimmer-L 000-255 0~100% 000-010 No Function 011-132 Strobe slow to fast(All pods) 3 Strobe 133-255 Value Percent/Setting 1 White1 000-255 0~100% 2 White2 000-255 0~100% 3 White3 000-255 0~100% 4 White4 000-255 0~100% 15CH Function Value Percent/Setting 1 Dimmer-H 000-255 0~100% 2 Dimmer-L 000-255 0~100% 000-010 No Function 011-132 133-255 0~100% 5 White1-L 000-255 0~100% White1- 000-010 No Function Strobe 011-255 Strobe slow to fast 7 White2-H 000-255 0~100% 8 White2-L 000-255 0~100% White2- 000-010 No Function Strobe 011-255 Strobe slow to fast 10 White3-H 000-255 0~100% 11 White3-L 000-255 0~100% White3- 000-010 No Function Strobe 011-255 Strobe slow to fast 13 White4-H 000-255 0~100% 14 White4-L 000-255 0~100% White4- 000-010 No Function Strobe 011-255 Strobe slow to fast 15 NEO BLINDER MKII VERSIÓN ESPAÑOL 16 Bit strobe macros) 000-255 12 Remark Strobe Slow to Fast(All pods) White1-H 9 Remark Strobe Slow to Fast (Random 4 6 16Bit strobe macros) Function Strobe Remark Strobe slow to fast (Random 4CH 3 Remark 16 Bit 16 Bit 16 Bit 16 Bit p. 9 Menu del NEO BLINDER MKII NO. 1 2 Main Menu Auto Show Static Menu level 2 Menu level Menu 3 level4 Remark Auto Show Speed <Auto 1> <100> <Auto 2> <100> <Auto 3> <100> <Auto 4> <100> <Auto 5> <100> <Auto 6> <100> <Dimmer> <255> Default: Dim- <Strobe> <0> mer=255;Strobe=0 Default: Auto 1;Speed:100 <Off> 3 Dimmer <Dimmer 1> Mode <Dimmer 2> Default: 0FF <Dimmer 3> <On> 5 Back Light <10S> Default: On <20S> <30S> 6 7 Information DMX Address Auto <Test> Fixture Hours <9999> Version <V1.0> 1 Default: 001 <1Ch> 8 DMX Chan- <3Ch> nel <4Ch> Default: 15CH <15Ch> 9 10 Master/ <Master> Slave <Slave> Fan Mode <Auto> Default:Slave 40ºC <High> <LED1:40ºC> 11 Tempera- <LED2:40ºC> ture <LED3º40C> <LED4º40C> 600Hz 12 LED Frequency 1200 Hz 2000 Hz Default: 1200HZ 4000 Hz 25KHz NEO BLINDER MKII VERSIÓN ESPAÑOL p. 10 NEO BLINDER MKII - Tabla de parametros NEO BLINDER MKII VERSIÓN ESPAÑOL p. 11 NEO BLINDER MKII