LASSO/ EXTERIOR

Installation Instructions
LASSO/ EXTERIOR
WARNING - PLEASE READ ALL
INSTRUCTIONS PRIOR TO INSTALLATION
Lasso endcap
TURN OFF POWER PRIOR TO ANY WORK ON THE SYSTEM.
Lasso
Lasso straps
DO NOT COVER THIS PRODUCT. UNCOIL FLEXIBLE LIGHT PRIOR TO
PLUGGING INTO OUTLET AS IT CAN CAUSE LIGHT TO OVERHEAT,
MELT OR IGNITE.
DO NOT USE OR INSTALL DAMAGED PRODUCT. INSPECT
PERIODICALLY.
Surface mount screws
DO NOT SUBMERGE. DO NOT USE IN THE VICINITY OF STANDING
WATER.
SECURE WITH LASSO CHANNEL OR LASSO STRAPS ONLY.
DO NOT INSTALL ON GATES, DOORS, OR WHERE SUBJECT TO
CONTINUOUS FLEXING.
DO NOT ROUTE CORD OR LASSO THROUGH WALLS, DOORS,
WINDOWS, OR ANY LIKE PART OF THE BUILDING STRUCTURE.
Installing, wiring, and maintenance must be done by qualified persons or a
certified electrician in accordance with all local and National Electrical Codes.
Warranty is voided in case of unauthorized modifications and/or improper use.
Save these instructions and refer to them when additions, changes, or services
to the system are made.
Do not exceed 124 feet. (37.8 meters) per power feed kit.
Lasso
channel
Ground Fault Circuit Interrupter (GFCI) protection should be provided on
the circuit or outlet to be used for the outdoor use flexible lighting product.
Receptacles are available having built-in GFCI protection for this measure of
safety.
ETLus Listed to UL2388 (suitable for indoor and outdoor use)
cETL Listed to CSA C22.2 #9.0
IP54
Product is suitable for a location where water or other liquid can drip, splash,
or flow on.
Not intended for immersing in water or other liquids.
Lasso exterior power feed
INSTRUCTIONS FOR USE
1 Carefully insert pointed side of splice connector into wiring of Lasso.
2 For ease of assembly, soften clear sleeve on exterior power feed by using
heat gun.
Lasso splice connector
3 Firmly hold the exterior power feed and Lasso, and carefully insert
Lasso into exterior power cord assembly until blunt side of splice
connectors are fully seated.
4 Cut Lasso Channel to size as needed. Install Lasso Channel by drilling 1/8
in. (3.175 mm) holes every 12 in. (30.48 cm) or as required. Press Lasso
into Lasso Channel. Alternative installation method is to use Lasso Straps
for curves or arches as needed.
5 Plug exterior power feed into outlet and test for proper operation.
6 If Lasso does not light, reverse polarity.
Fuse cap
7 Unplug power cord from outlet.
8 Remove Lasso from exterior power feed (heat gun may be required), rotate
exterior power feed 180 degrees and insert back into exterior power feed.
Fuse
1"
9 Plug exterior power feed into outlet and test for proper operation.
41 3/4"
v.9.02.15
Ledra Brands Inc.
15774 Gateway Circle
Tustin, CA 92780
p:714.259.9959
f:714.259.9969
In a continuing effort to offer the best product possible we reserve the right to change, without
notice, specifications or materials that in our opinion will not alter the function of the product.
www.LedraBrands.com
IMPORTANT INFORMATION
WARNING
ADVERTENCIA
AVERTISSEMENT
• To avoid possible electrical shock, before
installing light fixtures, disconnect power
by turning off the circuit breakers and the
wall switch. Use appropriate lock out, tag
out procedures.
• Para evitar posibles choques eléctricos,
antes de instalar luminarios, desconecte
el alimentación apagando los
interruptores de circuito y el interruptor
de pared. Use adecuado procedimientos
de bloqueo y etiquetas.
• Pour éviter les chocs électriques, avant
d’installer des appareils d’éclairage,
coupez l’alimentation en désactivant
les disjoncteurs et l’interrupteur mural.
Utilisation appropriée est bloquée, balise
les procédures.
• Compruebe que el voltaje de
alimentación es correcto comparándolo
con la información de etiqueta de el
luminario.
• Assurez-vous que la tension d’alimentation
est correcte en comparant les informations
d’étiquette de luminaire.
• Ensure that supply voltage is correct by
comparing readings to the luminaire label
information.
• Make all electrical and grounding
connections in accordance with the
National Electrical Code (NEC) and any
applicable local code requirements.
• Hacer todas las conexiones eléctricas y
puesta a tierra de acuerdo con el código
eléctrico nacional (NEC) y los requisitos
del código local aplicable.
• Allow sufficient time to cool before
servicing.
• Permite suficiente tiempo para enfriar
antes de empesar servicio.
CAUTION
PRECAUCION
• Wiring must be done in accordance with
national and local electrical codes and
ANSI/NFPA 70.
• Todo el cableado debe hacerse de
conformidad con los códigos eléctricos
nacionales y locales y ANSI/NFPA 70. Si
no está familiarizado con el cableado,
debe utilizar a un electricista certificado.
• PPE Personal Protective Equipment such
as gloves and safety glasses should
be used at all times when installing,
maintaining, and servicing.
• Risk of fire. Keep combustible material
away from fixtures.
v.9.02.15
Ledra Brands Inc.
• Equipo de protección personal como
guantes y lentes de seguridad se debe
utilizar al instalar, mantener o reparar.
• Faire tous les raccordements électriques
et mise à la terre selon le Code électrique
National (NEC) et des exigences du code
local applicable.
• Laisser suffisamment de temps avant
l’entretien.
MIS EN GARDE
• Câblage doit être conforme aux codes
électriques locaux et nationaux et ANSI/
NFPA 70..
• Tout le câblage doit être effectué par un
électricien certifié.
• Risque d’incendie. Garder les matières
combustibles loin de luminaires.
• Riesgo de incendio. Mantenga los
materiales combustibles lejos de los
liminarios.
15774 Gateway Circle
Tustin, CA 92780
p:714.259.9959
f:714.259.9969
In a continuing effort to offer the best product possible we reserve the right to change, without
notice, specifications or materials that in our opinion will not alter the function of the product.
www.LedraBrands.com