Descargar - Sistemas Sin Cuotas
Transcripción
Descargar - Sistemas Sin Cuotas
MCT-237 User Guide Wireless CodeSecure™ Two-Way Keyfob Transmitter 1. INTRODUCTION 1.1 Description The MCT-237 is a miniature CodeSecure™ 6-button keyfob transmitter, designed for use with the PowerMax Pro unit. The device enables the user to arm/disarm the alarm system and to view system status. For each PowerMax Pro control panel, a maximum of eight MCT-237 keyfob devices may be enrolled. Operating power is obtained from an internal 1.5 V alkaline battery. Each transmitter is supplied with a small keyring. Transmission is initiated by pressing any one of the six pushbuttons. Upon pressing a specific button, the keyfob transmits a CodeSecure™ digital sequence identifiable by the PowerMax unit, and a 4-bit function code associated with the button that was pressed. The next time a button is pressed, the keyfob will transmit a digital sequence of three transmissions that differs from the one used in the previous transmission and the respective function code. As a result, malicious “code grabbing” is virtually impossible. The main features of the MCT-237 are: • Status, alarm memory, and trouble data retrieval from PowerMax Pro. • Visual indications by LCD icon display. • LCD backlighting activation. • Various audible signals sounded by the speaker in response to specific actions. • 1.5 Volt Alkaline battery. Icon Definition Trouble: Indicates a trouble state is detected within the PowerMax Pro. Low Battery: Indicates the battery must be replaced without delay. In addition, a “low battery” report will be transmitted with the outgoing digital message. Communication: Indicates a communication failure Alarm: Indicates that the alarm has been activated ARM DISARM HOME STATUS AUX A AUX B 1.2 LCD Icons The following table provides definitions for each of the eight icons that appear on the LCD display. Icon Definition Lights when the system is in Arm Home mode Lights when the system is in Arm Away mode Lights when the system is disarmed Partition: Not available in this version PANIC (Press both buttons simultaneously for 2 seconds) Figure 1. External View 2. SPECIFICATIONS Frequency (MHz): 868.95, 315 Modulation: ASK (ON-OFF keying) Coding: CodeSecure Battery: 1.5 V AAA alkaline battery, type GP or equivalent Current Consumption: 35 mA during transmission Battery Life Expectancy: 2 years (for typical use) Note: If transmission is still possible despite the battery condition, the unit will send a low battery signal to the receiver. Control Functions: Home Arming, Away Arming, Disarming, System Status, AUX 1 and 2 Operating Temperature: 0° to 49°C (32° to 120°F). Dimensions: 75 x 38 x 18 mm (2-15/16 x 1-1/2 x 11/16 in.). Weight (including battery): 36 g (1¼ oz). Color: Black Compliance with Standards: EN 50131-1 Grade 2, Class II 3. TESTING AND MAINTENANCE 3.1 Testing a New Unit Since the keyfob transmitter is supplied with the battery already installed, the unit is practically ready to be tested. IMPORTANT! Before testing, "teach" the PowerMax Pro the ID code of the keyfob, as instructed in the PowerMax Pro Installer Guide. A. Stand near the PowerMax Pro control panel and press the keyfob button marked with a closed padlock icon. D-300280 B. Make sure that the control panel responds as programmed and as stated in the PowerMax Pro Installer Guide. C. Operate the keyfob from various locations within the area covered by the receiver to determine "dead" locations, where transmission is blocked by walls and large objects, or affected by structural materials. For optimum operation, point the keyfob directly toward the PowerMax Pro control panel. Note: If dead/marginal zones are a problem, relocating the PowerMax Pro control panel may improve the performance. 1 3.2 Replacing the Battery SLIDE THE COVER BACK ON 3 IN THE DIRECTION The battery should be replaced upon receiving a low battery LCD indication. A replacement 1.5 V AAA alkaline battery, such as GP (or equivalent), should be used. Replace the battery as follows: SHOWN 1 ON THE REVERSE SIDE OF THE UNIT, SLIDE THE COVER IN THE DIRECTION SHOWN THE BATTERY 2 EXTRACT FROM ITS HOLDER Figure 3. Inserting New Battery 3.3 Cleaning Figure 2. Battery Removal TEST THE UNIT BY MOMENTARILY PRESSING ONE OF THE TRANSMIT SWITCHES. THE LCD DISPLAY SHOULD LIGHT. 2 ( ) AAA ( ) The use of abrasives of any kind is strictly forbidden. Also never use solvents such as kerosene, acetone or thinner. INSERT THE NEW B ATTERY NOTE: INSERT B ATTERY WITH NEGATIVE (--) EDGE PRESSED AGAINST THE SPRING The transmitter may get dirty if touched with greasy fingers. Clean it only with a soft cloth or sponge moistened lightly with a mixture of water and mild detergent, and wipe it dry immediately. 1 4. DEFINING KEYFOB OPTIONS Note: To enroll the MCT-237, refer to the PowerMax Pro User Guide section 7 (User Settings) – Enrolling Keyfob Transmitters. Here you select the function of the two AUX buttons on the transmitter. Four options are offered for each AUX button: Status: Pressing the AUX button will cause the control panel’s voice module to announce the system status. Instant: Pressing the AUX button while the exit delay is in progress will cause the system to arm “instant” (the entry delay is canceled). Skip exit delay: Pressing the AUX button will immediately cause the system to arm. PGM / X-10: Pressing the AUX button will activate the PGM output or X-10 units. Proceed as shown in the following flow chart. READY 00:00 NORMAL MODE USER SETTINGS 17: AUX BUTTON A 18: AUX B 2-W-KF status instant skip exit delay PGM / X-10 status instant skip exit delay PGM / X-10 INSTALLER MODE ENTER CODE [installer code] 1. NEW INSTL CODE 2. ENROLLING 3. DEFINE ZONES 4. DEFINE PANEL <OK> TO EXIT Note: The currently saved options are displayed with dark box at the right side of the display. To review the options, repeatedly click or on the PowerMax Pro control panel until the desired option is displayed. Then, click OK (a dark box will be displayed at the right side). Figure 4: Performing PowerMax Pro Audio Functions GARANTÍA Visonic Ltd. y/o sus subsidiarias y afiliadas ("el Fabricante") garantiza que sus productos, en lo sucesivo denominados "el Producto" o "los Productos", se ajustan a sus propios planos y especificaciones y no presentan defectos de materiales o de fabricación en uso y servicio normales durante un periodo de doce meses a partir de la fecha de envío por el Fabricante. Las obligaciones del Fabricante durante el periodo de garantía se limitarán, a su elección, a la reparación o reemplazo del producto o partes del mismo. El Fabricante no será responsable de los costos de desmontaje y/o reinstalación. Para hacer uso de la garantía, el Producto deber ser devuelto al Fabricante con porte pagado y asegurado. Esta garantía no se aplica a los siguientes casos: Instalación inadecuada, mal empleo, inobservancia de las instrucciones de instalación y operación, alteración, abuso, accidente o manipulación no autorizado, y reparación por cualquiera que no sea el Fabricante. Esta garantía es exclusiva y expresamente en lugar de todas las demás garantías, obligaciones o responsabilidades, ya sea escritas, orales, explícitas o implícitas, incluyendo cualquier garantía de comerciabilidad o de adecuación para un fin determinado, u otras. El Fabricante no será responsable en ningún caso de daños indirectos incidentales cualesquiera por incumplimiento de esta garantía o de otras garantías cualesquiera, como se expresa más arriba. Esta garantía no debe ser modificada, alterada ni extendida, y el Fabricante no autoriza a nadie a actuar en su nombre en la modificación, alteración o extensión de esta garantía. Esta garantía se aplica al Producto solamente. Todos los productos, accesorios o añadidos de terceros que son utilizados junto con el Producto, incluyendo las baterías, serán amparados por su propia garantía solamente, si ésta existe. El Fabricante no será responsable de cualquier daño o pérdida, causados ya sea directa, indirecta, incidentalmente o de otra manera, por el funcionamiento defectuoso del Producto debido a productos, accesorios o añadidos de terceros, incluyendo baterías, que sean utilizados con el Producto. El Fabricante no pretende que su Producto no pueda ser comprometido o burlado, o que el Producto pueda evitar cualquier muerte, daños corporales o daños materiales u otras pérdidas resultantes de robo con fractura, robo, incendio u otros, o que el Producto pueda brindar una adecuada advertencia o protección en todos los casos. El usuario entiende que una alarma correctamente instalada y mantenida puede sólo reducir el riesgo de eventos como robo con fractura, robo e incendio sin aviso, mas no constituye un seguro o garantía de que los mismos no habrán de ocurrir o de que no se producirán muertes, daños corporales o daños materiales como resultado de ellos. El Fabricante no asume ninguna responsabilidad por muertes, daños corporales o daños materiales u otras pérdidas cualesquiera, ya sean directos, indirectos, incidentales o de otra naturaleza, basados en una afirmación de que el Producto no funcionó. Sin embargo, si el Fabricante fuese considerado directa o indirectamente responsable de cualquier pérdida o daño que se produzca al amparo de esta garantía limitada o de otra manera, sin tener en cuenta la causa u origen de los mismos, la responsabilidad máxima del Fabricante no podrá superar en ningún caso el precio de adquisición del producto. Dicha responsabilidad será fijada como una indemnización y no como una pena, y constituirá el único y exclusivo recurso contra el Fabricante. Advertencia: El usuario deberá obedecer las instrucciones de instalación y funcionamiento, y entre otras cosas, probará el Producto y la totalidad de sistema por lo menos una vez por semana. Por diversas razones, entre ellas cambios de las condiciones ambientales, trastornos eléctricos o electrónicos y manipulación indebida o no autorizada, el Producto puede no funcionar como se espera. Se aconseja al usuario tomar todas las precauciones necesarias para su propia seguridad y para la protección de su propiedad. (6/91) W.E.E.E. Product Recycling Declaration For information regarding the recycling of this product you must contact the company from which you orignially purchased it. If you are discarding this product and not returning it for repair then you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste. Directive 2002/96/EC Waste Electrical and Electronic Equipment. VISONIC LTD. (ISRAEL): P.O.B 22020 TEL-AVIV 61220 ISRAEL. PHONE: (972-3) 645-6789, FAX: (972-3) 645-6788 INTERNET:www.visonic.com VISONIC IBERICA SEGURIDAD, SL: C/ ISLA DE PALMA, 32 - NAVE 7, POLÍGONO INDUSTRIAL NORTE, 28700 SAN SEBASTIÁN DE LOS REYES, (MADRID), ESPAÑA. TEL (34) 91659-3120, FAX (34) 91663-8468 INTERNET:www.visonic-iberica.es VISONIC LTD. 2006 MCT-237 D-300280 (REV. 0, 06/06) 2 D-300280