Regulador de tensión TAPCON®

Regulador de tensión
TAPCON®
Hoja suplementaria
4075790/00 ES . Descripción del protocolo IEC 60870-104
© Todos los derechos reservados por Maschinenfabrik Reinhausen
Queda prohibida cualquier reproducción o copia de este documento, así como la utilización y divulgación de su
contenido, a no ser que se autorice expresamente.
Las infracciones conllevan una indemnización por daños. Reservados todos los derechos para casos de registro
de patente, modelo de utilidad y diseño industrial.
Es posible que tras la redacción de la siguiente documentación se hayan producido modificaciones en el
producto.
Nos reservamos expresamente el derecho a realizar modificaciones de los datos técnicos así como en la
construcción del aparato y en el volumen de entrega.
Las informaciones proporcionadas y los acuerdos establecidos durante la tramitación de las ofertas y los
pedidos en curso son siempre vinculantes.
Las instrucciones de servicio originales han sido redactadas en alemán.
Índice
Índice
1
Introducción ........................................................................................................................ 4
2
Interfaces físicas ................................................................................................................. 5
3
Ajuste de los parámetros del aparato ............................................................................... 6
4
Puntos de entrada de datos ............................................................................................... 7
4.1
Dirección de control de funcionamiento ASDU ................................................................................... 7
4.1.1
Señalizaciones individuales .................................................................................................................................. 7
4.1.2
Señalizaciones dobles......................................................................................................................................... 10
4.1.3
Mensaje de posición de toma.............................................................................................................................. 10
4.1.4
Valores de medición ............................................................................................................................................ 11
4.1.5
Valores de medición; valor escalado................................................................................................................... 13
4.2
Dirección de control ASDU ................................................................................................................ 13
4.2.1
Órdenes de posición de toma ............................................................................................................................. 13
4.2.2
Órdenes individuales ........................................................................................................................................... 13
4.2.3
Órdenes de ajuste de valor consigna .................................................................................................................. 14
Glosario.............................................................................................................................. 16
Maschinenfabrik Reinhausen 2014
4075790/00 ES
TAPCON®
3
1 Introducción
1 Introducción
Esta documentación técnica está exclusivamente dirigida a personal especializado con la autorización y formación necesarias.
4
TAPCON®
4075790/00 ES
Maschinenfabrik Reinhausen 2014
2 Interfaces físicas
2 Interfaces físicas
El aparato está diseñado conforme a los estándares CEM correspondientes.
Con el fin de cumplir los estándares de compatibilidad electromagnética
(CEM), tenga en cuenta el apartado correspondiente sobre el tema "Compatibilidad electromagnética" de las instrucciones de servicio del aparato.
Encontrará más información sobre las interfaces físicas en las instrucciones
de servicio del aparato.
Maschinenfabrik Reinhausen 2014
4075790/00 ES
TAPCON®
5
3 Ajuste de los parámetros del aparato
3 Ajuste de los parámetros del aparato
Para utilizar el protocolo del centro de control, debe ajustar los parámetros
del aparato.
Tenga en cuenta las instrucciones de servicio del aparato para obtener más
información sobre el ajuste de los parámetros del aparato.
Debe ajustar los siguientes parámetros:
Parámetro
Margen de ajuste
Dirección IP
Máscara de la subred
Dirección del gateway
Puerto TCP
Dirección ASDU
0.0.0.0...255255255255
0.0.0.0...255255255255
0.0.0.0...255255255255
0...65535
0...65535
Tabla 1: Parámetros del aparato
6
TAPCON®
4075790/00 ES
Maschinenfabrik Reinhausen 2014
4 Puntos de entrada de datos
4 Puntos de entrada de datos
En el siguiente apartado se describen los puntos de entrada de datos máximos posibles del protocolo. Tenga en cuenta que según la configuración solicitada de su aparato, solo está disponible una parte de los puntos de entrada de datos.
4.1 Dirección de control de funcionamiento ASDU
4.1.1 Señalizaciones individuales
▪
ASDU Type = 1
▪
General interrogation = 1
▪
Grupo (QOI) = 1
Nombre
SPI value
Dirección del objeto
de información
Automatic/Manual operation
Band center voltage (desired value) 1 active
Band center voltage (desired value) 2 active
Band center voltage (desired value) 3 active
Band center voltage (desired value) 4 active
Band center voltage (desired value) 5 active
Parallel/Independent
Master mode selection activation (parallel control)
Follower mode selection activation(parallel control)
Circulating current selection activation (parallel
control)
Line Drop Compensation is R and X or Z model
(1=R and X, 0=Z compensation)
Time delay linear or inverse characteristic
(0=lin., 1=inv.)
Error of parallel operation
Local operation
Function monitoring
0 = Manual; 1 = Automatic
1 = Active Bandcenter 1
1 = Active Bandcenter 2
1 = Active Bandcenter 3
1 = Active Bandcenter 4
1 = Active Bandcenter 5
0 = Independent; 1 = Parallel
1 = Active Master Paralleling
1
2
3
4
5
6
7
8
1 = Active Follower Paralleling
1 = Active Circulating Current Paralleling
0 = Z; 1 = LDC;
9
0 = linear; 1 = inverse
12
1 = paralleling error
0 = remote; 1 = local
1 = function monitoring active
1 = LTC inhibit
1 = LTC inhibit
1 = LTC inhibit
1 = end position reached
13
15
17
1 = end position reached
23
LTC inhibit due to under voltage
LTC inhibit due to over voltage
LTC inhibit due to over current
End position raise or highest allowed tap position reached
End position lower or lowest allowed tap position
reached
Maschinenfabrik Reinhausen 2014
4075790/00 ES
10
11
19
20
21
22
TAPCON®
7
4 Puntos de entrada de datos
Nombre
SPI value
Dirección del objeto
de información
Block Automatic Control
1 = automatic control blocked
1 = limit exceeded
1 = limit exceeded
1 = limit exceeded
1 = limit exceeded
1 = limit exceeded
1 = limit exceeded
1 = limit exceeded
1 = limit exceeded
1 = limit exceeded
1 = limit exceeded
1 = limit exceeded
1 = limit exceeded
1 = limit exceeded
1 = limit exceeded
1 = limit exceeded
1 = limit exceeded
1 = limit exceeded
1 = limit exceeded
1 = limit exceeded
1 = limit exceeded
1 = limit exceeded
1 = limit exceeded
1 = failure
0= Standard; 1=Dynamic
Setpoint Control
1 = error
1 = motor drive running
1 = motor drive running
1 = motor drive running
1 = motor drive running
1 = tap indication error
24
1 = tap indication error
271
1 = tap indication error
272
1 = tap indication error
273
1 = motor drive local
274
Voltage high limit exceeded
Voltage high limit 2 exceeded
Voltage low limit exceeded
Voltage low limit 2 exceeded
Current overload
Current overload 2
Current underload
Current underload 2
Apparent power high limit exceeded
Apparent power high limit 2 exceeded
Apparent power low limit exceeded
Apparent power low limit 2 exceeded
Active power high limit exceeded
Active power high limit 2 exceeded
Active power low limit exceeded
Active power low limit 2 exceeded
Reactive power high limit exceeded
Reactive power high limit 2 exceeded
Reactive power low limit exceeded
Reactive power low limit 2 exceeded
Power Factor (Cosinus phi) low limit exceeded
Power Factor (Cosinus phi) low limit 2 exceeded
Voltage input failure (e.g. missing connection)
Setpoint Control Mode
Dynamic Setpoint Control error
Motor drive of transformer 1 running
Motor drive of transformer 2 running
Motor drive of transformer 3 running
Motor drive of transformer 4 running
Tap indication error (e.g. wrong BCD code) of
transformer 1
Tap indication error (e.g. wrong BCD code) of
transformer 2
Tap indication error (e.g. wrong BCD code) of
transformer 3
Tap indication error (e.g. wrong BCD code) of
transformer 4
Motor drive of transformer 1 in local mode
8
TAPCON®
4075790/00 ES
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
266
267
268
269
270
Maschinenfabrik Reinhausen 2014
4 Puntos de entrada de datos
Nombre
SPI value
Dirección del objeto
de información
Motor drive of transformer 2 in local mode
Motor drive of transformer 3 in local mode
Motor drive of transformer 4 in local mode
Tap Pos Difference in Transformer Bank
DIO Input 1
DIO Input 2
DIO Input 3
DIO Input 4
DIO Input 5
DIO Input 6
DIO Input 7
DIO Input 8
DIO Input 9
DIO Input 10
DIO Input 11
DIO Input 12
DIO Input 13
DIO Input 14
DIO Input 15
DIO Input 16
DIO Input 17
DIO Input 18
DIO Input 19
DIO Input 20
DIO Input 21
DIO Input 22
DIO Input 23
DIO Input 24
DIO Input 25
DIO Input 26
DIO Input 27
DIO Input 28
DIO Input 29
DIO Input 30
DIO Input 31
DIO Input 32
DIO Input 33
DIO Input 34
DIO Input 35
DIO Input 36
1 = motor drive local
1 = motor drive local
1 = motor drive local
1 = tap position difference
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
275
276
277
278
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
Maschinenfabrik Reinhausen 2014
4075790/00 ES
TAPCON®
9
4 Puntos de entrada de datos
Nombre
SPI value
Dirección del objeto
de información
DIO Input 37
DIO Input 38
DIO Input 39
DIO Input 40
DIO Input 41
DIO Input 42
General Purpose Message 1 (GPM1)
General Purpose Message 2 (GPM2)
General Purpose Message 3 (GPM3)
General Purpose Message 4 (GPM4)
General Purpose Message 5 (GPM5)
General Purpose Message 6 (GPM6)
General Purpose Message 7 (GPM7)
General Purpose Message 8 (GPM8)
General Purpose Message 9 (GPM9)
General Purpose Message 10 (GPM10)
General Purpose Command 1 Event (GPC1)
General Purpose Command 2 Event (GPC2)
General Purpose Command 3 Event (GPC3)
General Purpose Command 4 Event (GPC4)
General Purpose Command 5 Event (GPC5)
General Purpose Command 6 Event (GPC6)
General Purpose Command 7 Event (GPC7)
General Purpose Command 8 Event (GPC8)
General Purpose Command 9 Event (GPC9)
General Purpose Command 10 Event (GPC10)
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = input active
1 = active; 0 = inactive
1 = active; 0 = inactive
1 = active; 0 = inactive
1 = active; 0 = inactive
1 = active; 0 = inactive
1 = active; 0 = inactive
1 = active; 0 = inactive
1 = active; 0 = inactive
1 = active; 0 = inactive
1 = active; 0 = inactive
1 = active; 0 = inactive
1 = active; 0 = inactive
1 = active; 0 = inactive
1 = active; 0 = inactive
1 = active; 0 = inactive
1 = active; 0 = inactive
1 = active; 0 = inactive
1 = active; 0 = inactive
1 = active; 0 = inactive
1 = active; 0 = inactive
161
162
163
164
165
166
185
186
187
188
189
190
191
192
193
194
300
301
302
303
304
305
306
307
308
309
Tabla 2: Einzelmeldungen
4.1.2 Señalizaciones dobles
Nombre
Description
DPI value
ASDU Type
Dirección del
objeto de
información
General
interrogation
Group (QOI)
Health
-
01 = OK; 10 = warning; 11 = error
3
16
1
1
Tabla 3: Señalizaciones dobles
4.1.3 Mensaje de posición de toma
▪
10
TAPCON®
ASDU Type = 5
4075790/00 ES
Maschinenfabrik Reinhausen 2014
4 Puntos de entrada de datos
▪
General interrogation = 1
▪
Group (QOI) = 2
Nombre
Dirección del objeto de información
Tap Position
Tap Position of transformer 1
Tap Position of transformer 2
Tap Position of transformer 3
Tap Position of transformer 4
100
258
260
262
264
Tabla 4: Mensaje de posición de toma
4.1.4 Valores de medición
▪
ASDU Type = 13
▪
General interrogation = 1
▪
Group (QOI) = 2
Nombre
Unit
Dirección del objeto
de información
Band width voltage (as percent of nominal voltage)
Control intentional time delay (in seconds)
Line drop voltage due to line resistance component (ohmic behaviour of the cable)
Line drop voltage due to line reactance component (inductive behaviour of the cable)
Control voltage below which auto Lower commands blocked (relative)
Limit Load Current (LTC Block Load Current,
percentage)
Line drop voltage due to line total impedance
(percentage of nominal voltage)
Band center voltage 1
Band center voltage 2
Band center voltage 3
Band center voltage 4
Band center voltage 5
Band center voltage (actual reference - can not
be set)
Control Voltage
Control Voltage Deviation (in percent of BndCtr)
Load Current (transformer secondary current)
Phase Angle of LodA relative to CtlV
Circulating Current (reactive)
%
50
s
Ohm/m
51
52
Ohm/m
53
%
54
A
55
%
56
V
V
V
V
V
V
59
60
61
62
63
64
V
%
A
°
A
65
66
67
68
69
Maschinenfabrik Reinhausen 2014
4075790/00 ES
TAPCON®
11
4 Puntos de entrada de datos
Nombre
Unit
Dirección del objeto
de información
Maximum voltage value for dynamic setpoint
control
Minimum voltage value for dynamic setpoint
control
Voltage value for dynamic setpoint control at active power of 0 W
Maximum active power value for dynamic setpoint control
Minimum active power value for dynamic setpoint control
Total active power (total P)
Total reactive power (total Q)
Total apparent power (total S)
Average power factor (total PF)
Frequency
Phase to phase voltage L1L2
Phase to phase voltage L2L3
Phase to phase voltage L3L1
Phase to neutral voltage L1
Phase to neutral voltage L2
Phase to neutral voltage L3
Phase current L1
Phase current L2
Phase current L3
Phase current N
Phase active power (P) L1
Phase active power (P) L2
Phase active power (P) L3
Phase reactive power (Q) L1
Phase reactive power (Q) L2
Phase reactive power (Q) L3
Phase apparent power (S) L1
Phase apparent power (S) L2
Phase apparent power (S) L3
Phase power factor L1
Phase power factor L2
Phase power factor L3
Phase Angle U1I1
Phase Angle U2I2
Phase Angle U3I3
V
102
V
103
V
104
W
105
W
106
W
VAr
VA
Hz
V
V
V
V
V
V
A
A
A
A
W
W
W
VAr
VAr
VAr
VA
VA
VA
°
°
°
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
Tabla 5: Valores de medición
12
TAPCON®
4075790/00 ES
Maschinenfabrik Reinhausen 2014
4 Puntos de entrada de datos
4.1.5 Valores de medición; valor escalado
▪
ASDU Type = 11
▪
General interrogation = 1
▪
Group (QOI) = 2
Nombre
Dirección del objeto de información
Tap position of Load Tap Changer where automatic Raise
commands are blocked
Tap position of Load Tap Changer where automatic Lower
commands are blocked
Tap Position
Tap Position of transformer 1
Tap Position of transformer 2
Tap Position of transformer 3
Tap Position of transformer 4
57
58
101
259
261
263
265
Tabla 6: Valores de medición; valor escalado
4.2 Dirección de control ASDU
4.2.1 Órdenes de posición de toma
▪
ASDU Type = 47
▪
General interrogation = 0
Nombre
RCS value
Dirección del objeto
de información
Change Tap Position
Change Voltage
Change Tap Position Bank Transformer 1
Change Voltage Bank Transformer 1
Change Tap Position Bank Transformer 2
Change Voltage Bank Transformer 2
Change Tap Position Bank Transformer 3
Change Voltage Bank Transformer 3
Change Tap Position Bank Transformer 4
Change Voltage Bank Transformer 4
01 = lower; 10 = raise
01 = lower; 10 = raise
01 = lower; 10 = raise
01 = lower; 10 = raise
01 = lower; 10 = raise
01 = lower; 10 = raise
01 = lower; 10 = raise
01 = lower; 10 = raise
01 = lower; 10 = raise
01 = lower; 10 = raise
200
201
250
251
252
253
254
255
256
257
Tabla 7: Stufenstellbefehle
4.2.2 Órdenes individuales
Maschinenfabrik Reinhausen 2014
▪
ASDU Type = 45
▪
General interrogation = 0
4075790/00 ES
TAPCON®
13
4 Puntos de entrada de datos
Nombre
SCS value
Dirección del objeto
de información
Automatic/Manual operation
Band center voltage (desired value) 1 active
Band center voltage (desired value) 2 active
Band center voltage (desired value) 3 active
Band center voltage (desired value) 4 active
Band center voltage (desired value) 5 active
Parallel/Independent
Master mode selection activation (parallel control)
Follower mode selection activation(parallel control)
Circulating current selection activation (parallel
control)
Line Drop Compensation is R and X or Z model
(1=R and X, 0=Z compensation)
Time delay linear or inverse characteristic
(0=lin., 1=inv.)
Setpoint Control Mode
0 = Manual; 1 = Automatic
1 = Activate Bandcenter 1
1 = Activate Bandcenter 2
1 = Activate Bandcenter 3
1 = Activate Bandcenter 4
1 = Activate Bandcenter 5
0 = Independent; 1 = Parallel
1 = Activate Master Paralleling
1 = Activate Follower Paralleling
1 = Activate Circulating Current Paralleling
0 = Z; 1 = LDC;
202
203
204
205
206
207
208
209
0 = linear; 1 = inverse
213
0= Standard; 1=Dynamic
Setpoint Control
0 = deactivate; 1 = activate
0 = deactivate; 1 = activate
0 = deactivate; 1 = activate
0 = deactivate; 1 = activate
0 = deactivate; 1 = activate
0 = deactivate; 1 = activate
0 = deactivate; 1 = activate
0 = deactivate; 1 = activate
0 = deactivate; 1 = activate
0 = deactivate; 1 = activate
214
General Purpose Command 1 (GPC1)
General Purpose Command 2 (GPC2)
General Purpose Command 3 (GPC3)
General Purpose Command 4 (GPC4)
General Purpose Command 5 (GPC5)
General Purpose Command 6 (GPC6)
General Purpose Command 7 (GPC7)
General Purpose Command 8 (GPC8)
General Purpose Command 9 (GPC9)
General Purpose Command 10 (GPC10)
210
211
212
215
216
217
218
219
220
221
222
223
224
Tabla 8: Einzelbefehle
4.2.3 Órdenes de ajuste de valor consigna
▪
General interrogation = 0
Nombre
Unit
ASDU Type
Dirección
del objeto
de información
Band width voltage (as percent of nominal voltage)
Control intentional time delay (in seconds)
%
50
225
s
50
226
14
TAPCON®
4075790/00 ES
Maschinenfabrik Reinhausen 2014
4 Puntos de entrada de datos
Nombre
Unit
ASDU Type
Dirección
del objeto
de información
Line drop voltage due to line resistance component (ohmic behaviour of the cable)
Line drop voltage due to line reactance component (inductive behaviour of the cable)
Control voltage below which auto Lower commands blocked (relative)
Limit Load Current (LTC Block Load Current,
percentage)
Line drop voltage due to line total impedance
(percentage of nominal voltage)
Tap position of Load Tap Changer where automatic Raise commands are blocked
Tap position of Load Tap Changer where automatic Lower commands are blocked
Band center voltage 1
Band center voltage 2
Band center voltage 3
Band center voltage 4
Band center voltage 5
Maximum voltage value for dynamic setpoint
control
Minimum voltage value for dynamic setpoint
control
Voltage value for dynamic setpoint control at active power of 0 W
Maximum active power value for dynamic setpoint control
Minimum active power value for dynamic setpoint control
Ohm/m
50
227
Ohm/m
50
228
%
50
229
A
50
230
%
50
231
-
49
232
-
49
233
V
V
V
V
V
V
50
50
50
50
50
50
234
235
236
237
238
239
V
50
240
V
50
241
W
50
242
W
50
243
Tabla 9: Órdenes de ajuste de valor consigna
Maschinenfabrik Reinhausen 2014
4075790/00 ES
TAPCON®
15
Glosario
Glosario
ASDU
Abreviatura de unidad de datos de servicio de la
aplicación (Application Service Data Unit)
CEM
Compatibilidad electromagnética
IP
Internet Protocol (Protocolo de Internet)
TCP
Transmission Control Protocol
16
TAPCON®
4075790/00 ES
Maschinenfabrik Reinhausen 2014
MR worldwide
Australia
Reinhausen Australia Pty. Ltd.
17/20-22 St Albans Road
Kingsgrove NSW 2208
Phone: +61 2 9502 2202
Fax: +61 2 9502 2224
E-Mail: [email protected]
Brazil
MR do Brasil Indústria Mecánica Ltda.
Av. Elias Yazbek, 465
CEP: 06803-000
Embu - São Paulo
Phone: +55 11 4785 2150
Fax: +55 11 4785 2185
E-Mail: [email protected]
Canada
Reinhausen Canada Inc.
3755, rue Java, Suite 180
Brossard, Québec J4Y 0E4
Phone: +1 514 370 5377
Fax: +1 450 659 3092
E-Mail: [email protected]
India
Easun-MR Tap Changers Ltd.
612, CTH Road
Tiruninravur, Chennai 602 024
Phone: +91 44 26300883
Fax: +91 44 26390881
E-Mail: [email protected]
Indonesia
Pt. Reinhausen Indonesia
German Center, Suite 6310,
Jl. Kapt. Subijanto Dj.
BSD City, Tangerang
Phone: +62 21 5315-3183
Fax: +62 21 5315-3184
E-Mail: [email protected]
Iran
Iran Transfo After Sales Services Co.
Zanjan, Industrial Township No. 1 (Aliabad)
Corner of Morad Str.
Postal Code 4533144551
E-Mail: [email protected]
Italy
Reinhausen Italia S.r.l.
Via Alserio, 16
20159 Milano
Phone: +39 02 6943471
Fax: +39 02 69434766
E-Mail: [email protected]
Japan
MR Japan Corporation
German Industry Park
1-18-2 Hakusan, Midori-ku
Yokohama 226-0006
Phone: +81 45 929 5728
Fax: +81 45 929 5741
Malaysia
Reinhausen Asia-Pacific Sdn. Bhd
Level 11 Chulan Tower
No. 3 Jalan Conlay
50450 Kuala Lumpur
Phone: +60 3 2142 6481
Fax: +60 3 2142 6422
E-Mail: [email protected]
P.R.C. (China)
MR China Ltd. (MRT)
开德贸易（上海）有限公司
中国上海浦东新区浦东南路 360 号
新上海国际大厦 4 楼 E 座
邮编： 200120
电话：＋ 86 21 61634588
传真：＋ 86 21 61634582
邮箱：[email protected]
[email protected]
Russian Federation
OOO MR
Naberezhnaya Akademika Tupoleva
15, Bld. 2 ("Tupolev Plaza")
105005 Moscow
Phone: +7 495 980 89 67
Fax: +7 495 980 89 67
E-Mail: [email protected]
South Africa
Reinhausen South Africa (Pty) Ltd.
No. 15, Third Street, Booysens Reserve
Johannesburg
Phone: +27 11 8352077
Fax: +27 11 8353806
E-Mail: [email protected]
South Korea
Reinhausen Korea Ltd.
21st floor, Standard Chartered Bank Bldg.,
47, Chongro, Chongro-gu,
Seoul 110-702
Phone: +82 2 767 4909
Fax: +82 2 736 0049
E-Mail: [email protected]
U.S.A.
Reinhausen Manufacturing Inc.
2549 North 9th Avenue
Humboldt, TN 38343
Phone: +1 731 784 7681
Fax: +1 731 784 7682
E-Mail: [email protected]
United Arab Emirates
Reinhausen Middle East FZE
Dubai Airport Freezone, Building Phase 6
3rd floor, Office No. 6EB, 341 Dubai
Phone: +971 4 2368 451
Fax: +971 4 2368 225
Email: [email protected]
Luxembourg
Reinhausen Luxembourg S.A.
72, Rue de Prés
L-7333 Steinsel
Phone: +352 27 3347 1
Fax: +352 27 3347 99
E-Mail: [email protected]
Maschinenfabrik Reinhausen GmbH
Falkensteinstrasse 8
93059 Regensburg
4075790/00 ES ▪ 09/14 ▪
+49 (0)941 4090-0
+49(0)941 4090-7001
[email protected]
www.reinhausen.com