Speed-Feed® Universal 375 LH Trimmer Heads P/N 78890

Speed-Feed® Universal 375 LH Trimmer Heads P/N 78890

Speed-Feed® Universal 375 LH Trimmer Heads
P/N 78890-18001
Installation and Loading Instructions
Package Contents:
1 Speed-Feed® 375 LH Universal Mount Trimmer Head
Bushings
(F) 1 - 8mm x 1.25mm LH Bushing (3 notches)
(G) 1 - 10mm x 1.0mm LH Bushing (1 notch)
(E) 1 - 10mm x 1.25mm LH Bushing (No notches)
(J) 1 - 10mm x 1.25 LH Long Bushing (No notches)
(M) 1 - Reversible Nylon Spacer w/20/25/38 mm Recesses
Mounting Studs
(H) 1 – 7mm x 10mm Mounting Stud (Gold)
(I) 1 – 8mm x 10mm Mounting Stud (Silver)
B
C
d
A
Trimmer Head Installation
1. Insert locking tool (A) into gear case to lock output shaft (B). Remove existing cutting attachment (C) from unit
following manufacturer’s instructions.
IMPORTANT: Your unit must be equipped with a debris shield including a line cutter that will cut line to length
when trimmer line is advanced.
i
2. Install or reuse unit manufacturer’s gear case base plate (D). Base plate must support trimmer head and allow it
to rotate freely.
3. Select and Install Speed-Feed® Mounting Hardware
Use the Speed-Feed® Application Chart provided to identify the bushing or bushing and mounting stud
combination needed for your model.
IMPORTANT: For Echo units only. Check debris shield on unit for “R” mark between cutoff blade screws.
a.
Units with “R” mark – Speed-Feed® line head will fit on unit as is - go to Step 6.
b.
Units without “R” mark – Remove short bushing from Speed-Feed® line head and replace with long bushing (J) and use spacer (M).
h
f
g
e
J
M
NOTE: If your brand or model number is not listed, match the existing mounting hardware from your model
with Speed-Feed® mounting studs and/or bushings to determine the correct parts needed. If you need help,
visit www.speedfeedhead.com, or call the Consumer Product Support Department at 1-800-432-3246 from
8:30 am to 4:30 pm (Central Time) Monday through Friday.
e, f, g, or j
NOTE: Bushing (E) (used with LH1, LH2, LH6) is preinstalled in trimmer head. Bushing (F) (used with LH3,
LH4), bushing (G) (used with LH5), and (J) (used with LH6) are included in the package. If required, depress
locking tabs (T), and open trimmer head (K) to install new bushing. Reassemble trimmer head in reverse
order of disassembly. Make sure “L” mark is facing up when replacing spool. Trimmer head halves will snap
together tightly only if parts are properly assembled.
T
T
M
4. If required, install new mounting stud (H) (7mm x 10mm) or (I) (8mm x 10mm) into threaded hole in gear case
output shaft (B). Turn “LH” studs counterclockwise to tighten.
5. If required, place reversible spacer (M) on base plate of gearcase, matching spacer recess to pilot diameter of
base plate.
NOTE: When spacer is properly matched and installed, there should be no gap between spacer and base
plate on gearcase.
6. Attach New Trimmer Head (K)
Thread trimmer head counterclockwise on to mounting stud or output shaft. Hand-tighten only.
NOTE: There should be no gap between spacer and line head after tightening.
H,I
IMPORTANT: Do not force, otherwise threads will strip and cause permanent damage. Unscrew and confirm
correct thread size.
D
A
7. Remove locking tool (A) from gear case.
8. If necessary, cut trimmer lines so length does not extend beyond the cut-off blade on debris shield.
9. To feed trimmer line, bump bottom of trimmer head against ground while running at normal operating speed.
X7672050701
01/11
B
k
L
A
Têtes de coupe 375 LH universelles Speed-Feed® Réf. 78890-18001
Instructions d’installation et de chargement
Contenu :
1 tête de coupe à montage universel Speed-Feed® 375 LH
Manchons
(F) 1 - Manchon LH 8 mm x 1,25 mm (3 encoches)
(G) 1 - Manchon LH 10 mm x 1,0 mm (1 encoche)
(E) 1 - Manchon LH 10 mm x 1,25 mm (pas d’encoche)
(J) 1 - Manchon long LH 10 mm x 1,25 (pas d’encoche)
(M) 1 - Entretoise en nylon réversible avec logements de 20 mm, 25 mm et 38 mm
Goujons de montage
(H) 1 – Goujon de montage 7 mm x 10 mm (Or)
(I) 1 – Goujon de montage 8 mm x 10 mm (Argent)
B
C
d
A
Installation de la tête de coupe
1. Insérer un outil de blocage (A) dans le boîtier de transmission pour bloquer l’arbre de sortie (B). Retirer l’accessoire de coupe existant (C) de l’appareil en suivant les instructions du fabricant.
IMPORTANT : L’appareil doit être équipé d’un pare-débris comprenant un couteau de ligne coupant la ligne
de coupe à la bonne longueur lorsqu’elle avance.
i
h
2. Installer ou réutiliser la plaque de base de boîtier de transmission du fabricant de l’appareil (D.) La plaque de
base doit soutenir la tête de coupe et lui permettre de tourner librement.
3. Sélectionner et installer les accessoires de montage Speed-Feed®.
Utiliser le Tableau d’application Speed-Feed® fourni pour identifier le manchon ou la combinaison
manchon et goujon de montage nécessaire pour votre modèle.
IMPORTANT: Pour les unités Echo seulement. Regarder s’il y a un « R » sur le pare-débris entre les vis
de la lame de coupe.
a. Dans le cas d’un appareil marqué « R » : la tête de coupe Speed-Feed®d convient telle quelle pour cet appareil ; passer à l’étape 6.
b. Dans le cas d’un appareil sans marque « R » : retirer le manchon court (SB) de la tête de coupe SpeedFeed®, mettre le manchon long (J), et l’utilisation Entretoise (M).
f
g
e
J
M
e, f, g, or j
T
REMARQUE : Si la marque ou le numéro de modèle de l’appareil n’est pas indiqué, comparer ses
accessoires de montage avec les goujons de montage ou manchons Speed-Feed® pour déterminer les
bonnes pièces requises. Pour obtenir de l’aide, visiter www.speedfeedhead.com ou téléphoner au service
après-vente au 1-800-432-3246 du lundi au vendredi entre 8h30 et 16h30 (heure du centre des ÉtatsUnis).
T
REMARQUE : Le manchon (E) (utilisé avec LH1, LH2, LH6) est préinstallé dans la tête de coupe. Les
manchons (F) (utilisé avec LH3, LH4), (G) (utilisé avec LH5), et (J) (utilisé avec LH6)sont inclus dans
l’emballage. Le cas échéant, appuyer sur les languettes de verrouillage (T) et ouvrir la tête de coupe (K)
pour installer le nouveau manchon. Remonter la tête de coupe en reprenant à l’envers les étapes de
démontage. Vérifier, en remplaçant la bobine, que la marque « L » est tournée vers le haut. Les moitiés
du taille-bordure ne s’emboîtent correctement que si les pièces ont été correctement assemblées.
M
4.
Le cas échéant, mettre en place le nouveau goujon de montage (H) (7mm x 10mm o (I) 8mm x 10mm)
dans le trou taraudé de l’arbre de sortie du boîtier de transmission (B). Tourner les goujons « LH » dans le
sens antihoraire pour serrer.
5. Les cas échéant, mettre l’entretoise réversible (M) sur la plaque de base du boîtier de transmission, en
faisant correspondre le diamètre du logement de l’entretoise avec le diamètre-pilote de la plaque de base.
REMARQUE : Lorsque l’entretoise est bien adaptée et en place, il ne doit pas y avoir d’espace entre l’entretoise et la plaque de base du boîtier de transmission.
6. Fixer la nouvelle tête de coupe (K)
Tourner les têtes de coupe « LH » dans le sens antihoraire pour serrer. Serrer à la main seulement.
REMARQUE : Après serrage, il ne doit pas y avoir d’espace entre l’entretoise et la tête de coupe.
IMPORTANT : Ne pas forcer sur les goujons de montage, car cela endommagerait irrémédiablement le
filetage. Dévisser le goujon et vérifier la taille du filetage.
7. 8. 9. 2
Retirer l’outil de blocage (A) du boîtier de transmission.
Le cas échéant, couper la ligne de façon à ce qu’elle ne dépasse pas au-delà du couteaude ligne du paredébris.
Pour faire avancer la ligne de coupe, frapper le sol avec la tête de coupe pendant le fonctionnement à la
vitesse normale.
B
H,I
D
A
k
L
A
Speed-Feed® Universal 375 LH Fadenkopf
Artikelnummer 78890-18001
Montage Nachfüllanleitung
Packungsinhalt:
1 Fadenkopf Speed-Feed 375 LH
Adapter
(F) 1 - 8 mm x 1,25 mm LH Adapter (3 Markierungen)
(G) 1- 10 mm x 1,0 mm LH Adapter (1 Markierung)
(E) 1 - 10 mm x 1,25 mm LH Adapter (keine Markierung)
(J) 1 - 10mm x 1,25 mm LH Lange Adapter (keine Markierung)
(M) 1 - Abstandhalter
Stehbolzen
(H) 1 – 7 mm x 10 mm Stehbolzen (Gold)
(I) 1 – 8 mm x 10 mm x 1.25mm Stehbolzen (Silber)
B
C
d
A
Montage
1. Sperrwerkzeug (A) in die am Winkelgetriebe dafür vorgesehen Bohrung um den Antrieb zu fixieren.
Montiertes Schneidwerkzeug (C) nach Herstelleranweisung abbauen.
WICHTIG: Ihr Gerät muss mit einem Schutzschild ausgerüstet sein an welchem ein Fadenabschneider
montiert ist.
2.
3.
Montieren Sie die an ihrem Gerät vorhandene Getriebeschutzplatte. Diese muss ein freies drehen des
Fadenkopfs ermöglichen.
Montieren Sie jetzt den Speed-Feed® Fadenkopf mit für Ihr Gerät entsprechend benötigten Teile. Diese Teile
entnehmen Sie bitte der Liste in dieser Anleitung.
i
h
f
g
Wichtig: Für Echo-Einheiten nur. Prüfen Schutzschild auf Einheit für “R” zu kennzeichnen zwischen Cutoff Blattschnecken.
A.
B.
Geräte mit “R” kennzeichnen - gehen Sie zu Schritt 6 fort.
Geräte ohne „R“ kennzeichnen – von Speed-Feed® Fadenkopf entfernen Adapter und ersetzen mit
langen Adapter (J) und Nutzung Abstandshalter (M).
Anmerkung: Ist Ihr Hersteller oder Modell nicht in der Liste aufgeführt, vergleichen Sie die OriginalMontageteile Ihres Geräts mit denen des Speed-Feed® und die richtigen Teile herauszufinden. Sollten sie
Hilfe benötigen, wenden Sie sich an Ihren Speed Feed-Fachhändler.
e
J
M
e, f, g, or j
Anmerkung: Adapter (E) (verwendet mit LH1, LH2, LH6) sind im Fadenkopf bereits montiert. Adapter
(F) (verwendet mit LH3, LH4), Adapter (G) (verwendet mit LH5), und (J) (verwendet mit LH6) sind dieser
Packung beigelegt. Falls notwendig, drücken Sie die Sicherungslaschen (T), und öffnen den Fadenkopf
(K) um einen anderen Adapter zu installieren. Bauen sie den Fadenkopf in umgekehrter Reihenfolge
wieder zusammen. Vergewissern Sie sich dass sich die Markierung „L“ beim Zusammenbau oben auf
der Fadenspule befindet. Die beiden Hälften des Fadenkopfs rasen nur sicher ein wenn alle Teile korrekt
montiert sind.
4.
Falls notwendig die Stehbolzen (H) (7 mm x 10 mm) oder (I) (8 mm x 10 mm) in die Gewindebohrung (B)
des Winkelgetriebes schrauben. Stehbolzen mit Linksgewinde (LH) gegen den Uhrzeigersinn einschrauben
und festziehen.
5. Falls erforderlich, stellen Abstandshalter (M) auf der Getriebeschutzplatte der Getriebegehäuse.
T
T
M
Anmerkung: Als Abstandhalter proerly installiert ist, sollte es keine Kluft zwischen Abstandhalter und der Getriebeschutzplatte auf Getriebegehäuse werden.
6. Den neuen Speed-Feed Fadenkopf (K) montieren
Den Speed-Feed® Fadenkopf gegen den Uhrzeigersinn aufschrauben. Nur von Hand anziehen.
Anmerkung: Es sollte keine Lücke zwischen Abstandshalter undeinen Fadenkopf nach dem Anziehen.
D
WICHTIG: Keine Gewalt anwenden da sonst das Gewinde dauerhaft beschädigt wird. Fadenkopf
abnehmen und auf passendes Gewinde überprüfen.
7. Sperrwerkzeug (A) entnehmen.
8. Falls notwendig Fäden auf korrekte Länge kürzen.
9. Um Faden nachzustellen, den Fadenkopf, bei normaler Arbeitsdrehzahl Ihres Geräts, kurz auf den Boden
klopfen.
B
H,I
A
k
L
A
3
Testina per bordatore Speed-Feed® Universal 375 LH
Codice ricambio 78890-18001
Istruzioni di montaggio e caricamento
Contenuto della confezione:
1 testina per bordatore Speed-Feed® Universal 375 LH
Boccole
(F) 1 - boccola LH da 8 mm x 1,25 mm (3 tacche)
(G) 1 - boccola LH da 10 mm x 1,0 mm (1 tacca)
(E) 1 - boccola LH da 10 mm x 1,25 mm (nessuna tacca)
(J) 1 - lungo boccola LH 10mm x 1,25 mm (nessuna tacca)
(M) 1- Distanziatore
Perni di montaggio
(H) 1 - perno di montaggio da 7 mm x 10 mm (Or)
(I) 1 - perno di montaggio da 8 mm x 10 mm x 1.25mm (Argento)
B
C
d
A
Montaggio della testina del bordatore
1. Inserire l’utensile di bloccaggio (A) nel carter ingranaggi per bloccare l’alberino di uscita (B). Rimuovere
l’accessorio di taglio (C) presente nell’attrezzo seguendo le istruzioni fornite dal produttore.
IMPORTANTE: L’attrezzo deve essere dotato di una protezione antidetriti comprendente una fresa per filo
che consenta di regolare la lunghezza del filo quando necessario.
i
2. Installare o riutilizzare la piastra di base del carter ingranaggi fornita dal produttore (D). La piastra di base
deve supportare la testina del bordatore e consentirne la rotazione senza attrito.
3. Scegliere e installare i componenti di montaggio Speed-Feed® Utilizzare la Tabella di applicazione SpeedFeed® fornita di seguito per identificare la boccola o la combinazione boccola/perno di montaggio necessaria
per il proprio modello.
IMPORTANTE: : Per le unità di ECHO solo. Controlla protezione antidetriti per il simbolo ”R” tra le viti della lama di taglio.
A. Le unità con il simbolo “R”, andare al passaggio 6.
B. Unità senza il simbolo “R”, togliere boccola della testina del bordatore e sostituire con lunga boccola (J) e uso distanziatore (M).
h
f
g
e
J
M
NOTA: Se nell’elenco non è presente la marca/modello in proprio possesso, confrontare i componenti di
montaggio esistenti del proprio modello con i perni di montaggio e le boccole Speed-Feed® forniti per determinare quali pezzi impiegare. Per richiedere assistenza, visitare il sito Web www.speedfeedhead.com o
contattare il distributore locale per l’Italia, Cormik SPA, al numero (39) 0444-220-611.
e, f, g, or j
NOTA: La testina del bordatore viene fornita con la boccola (E) (usato con LH1, LH2, LH6) già preinstallata. La boccola (F) (usato con LH3, LH4), la boccola (G) (usato con LH5), e (J) (usato con LH6) sono
invece incluse nella confezione. Se necessario, premere le linguette di bloccaggio (T) per aprire la testina del
bordatore (K) e montare una nuova boccola. Riassemblare la testina del bordatore seguendo l’ordine inverso.
Durante la sostituzione della bobina, assicurarsi che la lettera “L” sia rivolta verso l’alto. Le due parti della
testina del bordatore si chiuderanno saldamente solo in seguito al montaggio corretto di tutti i componenti.
T
T
M
4. Se necessario, inserire un nuovo perno di montaggio (H) (7 mm x 10 mm) o (I) (8 mm x 10 mm) nel foro filettato dell’alberino di uscita del carter ingranaggi (B). Girare in senso antiorario i perni “LH” per stringerli.
5. Se necessario, il distanziatore posto (M) sulla la piastra di base della scatola ingranaggi.
NOTA: Quando distanziatore è installata correttamente, ci dovrebbe essere alcun divario tra il distanziale e la piastra di base della scatola ingranaggi.
6. Montaggio di una nuova testina del bordatore (K)
Avvitare in senso antiorario la testina del bordatore sul perno di montaggio o sull’alberino di uscita. Serrare
esclusivamente a mano.
NOTA: Non ci dovrebbe essere spazio tra il distanziatore e la testa linea dopo il serraggio.
D
IMPORTANTE: Non forzare l’avvitatura per evitare di causare la spanatura dei componenti e danneggiarli.
Svitare e verificare la dimensione corretta della filettatura.
A
7. Smontare l’utensile di bloccaggio (A).
8. Se necessario, accorciare il filo in modo che la lunghezza non si estenda oltre la lama tagliafilo della protezione antidetriti.
9. Per allungare il filo, battere a terra la parte inferiore della testina del bordatore durante il funzionamento a
velocità normale.
k
L
4
B
H,I
A
Cabezas de recortadora 375 LH universal Speed-Feed® N/P 78890-18001
Instrucciones de instalación y carga
Contenido del paquete:
1 cabeza de recortadora de montaje universal Speed-Feed® 375 LH
(F) 1 - Buje LH de 8 x 1,25 mm (3 muescas)
(G) 1 - Buje LH de 10 x 1,0 mm (1 muesca)
(E) 1 - Buje LH de 10 x 1,25 mm (sin muescas)
(J) 1 - Buje largo LH de 10 mm x 1,25 mm (sin muescas)
(M) 1 - Espaciador de nilón reversible con cavidades para 20, 25 y 38 mm
Espárragos de montaje
(H) 1 - Espárrago de montaje de 7 x 10 mm (Oro)
(I) 1 - Espárrago de montaje de 8 x 10 mm (Plata)
B
C
d
A
Instalación de la cabeza de la recortadora
1.
Introduzca la herramienta de traba (A) en la caja de engranajes para trabar el eje de salida (B). Quite el
accesorio de corte existente (C) de la unidad según las instrucciones del fabricante.
IMPORTANTE: Su unidad debe estar equipada con un protector de residuos incluido un cortador de hilo
que corte el hilo a la medida cuando se haga avanzar el hilo de la recortadora.
2. Instale o reutilice la placa de base (D) de la caja de engranajes del fabricante. La placa de base debe
soportar la cabeza de la recortadora y dejar que gire libremente.
Seleccione e instale la tornillería de montaje Speed-Feed®
Use el Cuadro de aplicaciones de Speed-Feed® proporcionado para identificar el buje o la combinación
de buje y espárrago de montaje necesarios para su modelo.
3. IMPORTANTE: Para las unidades de Echo solamente. Compruebe el protector de residuos (S) en la
unidad para la marca “R” entre tornillos de la hoja de corte.
a. Las unidades con la marca “R”, la cabeza de hilo de alimentación rápida se adaptará a la unidad tal como es, van al Paso 6.
b. Las unidades sin marca “R”, quite el buje corto de la cabeza de hilo de alimentación rápida, instale el buje largo (J), e uso el espaciador (M).
NOTA: Si su marca o número de modelo no aparece en la lista, haga corresponder la tornillería de
montaje existente de su modelo con espárragos de montaje Speed-Feed® y bujes para determinar las
piezas necesarias correctas. Si necesita ayuda, visite www.speedfeedhead.com, o llame al Departamento
de Respaldo de Productos del Consumidor al 1-800-432-3246 de 8:30 de la mañana a 4:30 de la tarde
(Hora Central) de lunes a viernes.
i
h
e
J
M
e, f, g, or j
NOTA: Los bujes (E) (usada con LH1, LH2, LH6) están instalados de antemano en las cabezas de las
recortadoras. Los bujes (F) (usada con LH3, LH4), (G) (usada con LH5), y (J) (usada con LH6) están
incluidos en el paquete. Si es necesario, oprima las lengüetas de traba (T), y abra la cabeza de la
recortadora (K) para instalar el nuevo buje. Vuelva a montar la cabeza de la recortadora en orden inverso
al desmontaje. Asegúrese de que la marca “L” esté apuntando hacia arriba al reemplazar el carrete. Las
válvulas de la recortadora encajarán entre sí de forma apretada sólo si las piezas están debidamente
montadas.
4. 5.
NOTA: Cuando el espaciador está bien adaptado e instalado, no debe haber una separación entre el
espaciador y la la placa de base de la caja de engranajes.
6. Sujete la nueva cabeza de la recortadora (K)
Gire las cabezas de las recortadoras “LH” hacia la izquierda para apretarlas. Apriete con la mano
solamente.
NOTA: No debe haber una separación entre el espaciador y la cabeza del hilo después del apriete.
T
M
Saque la herramienta (A) de traba de la caja de engranajes.
Si es necesario, corte los hilos de la recortadora de modo que la longitud no se extienda más allá de la hoja
de corte en el protector de residuos.
Para alimentar el hilo de la recortadora, golpee la parte inferior de la cabeza de la recortadora contra el
terreno mientras se hace funcionar a la velocidad de operación normal.
B
H,I
D
A
IMPORTANTE: No fuerce los espárragos de montaje, ya que de lo contrario las roscas se desgastarán y
causarán daños permanentes. Desatornille el espárrago y confirme el tamaño correcto de las roscas.
9. T
Si es necesario, instale el nuevo espárrago de montaje (H) (7mm x 10mm) o (I) (8mm x 10mm) en el
agujero roscado en el eje de salida de la caja de engranajes (B). Gire los espárragos “LH” hacia la
izquierda para apretarlos.
Si es necesario, coloque el espaciador reversible (M) en la placa de base de la caja de engranajes,
haciendo coincidir el diámetro de la cavidad del espaciador con el diámetro piloto de la placa de base.
7. 8. f
g
k
L
A
5
ENGLISH
375 LH Trimmer Head Total Line Capacity
Loading Trimmer Line
.080 (2.0 mm) dia. – 10’ (3 m)
.095 (2.4 mm) dia. – 10’ (3 m)
1. Cut one piece of line to recommended length.
2. Align arrows on top of knob with openings in eyelets.
3. Insert one end of trimmer line into an eyelet, and push line equal distance through trimmer
head.
4. Hold trimmer head while turning knob clockwise to wind line onto spool until about 5” (13 cm)
of each line remains exposed.
Trimmer head is now fully loaded and ready for operation.
FRANCAIS
Longueur totale capacité de ligne de coupe du taille-bordures 375 LH
.080 (2.0 mm) dia. – 10’ (3 m)
.095 (2.4 mm) dia. – 10’ (3 m)
Chargement de la ligne du taille-bordures
1.Couper un morceau de ligne de la longueur préconisée.
2.Aligner les flèches de la partie supérieure du bouton avec les trous des œillets.
3.Insérer une extrémité de la ligne de coupe dans un œillet et pousser la ligne jusqu’à milongueur à travers la tête de coupe.
4.Maintenir la tête de coupe en tournant le bouton dans le sens horaire pour enrouler la
ligne sur la bobine jusqu’à ce qu’il reste une longueur d’environ 13 cm (5”) sortie à chaque
extrémité.
La tête de coupe est à présent complètement chargée et prête pour le
fonctionnement.
DEUTSCH
Fadenkopf 375 LH Spulenkapazität
Nylonfaden nachladen
2,0 mm Faden - 3 m
2,4 mm Faden - 3 m
1. Faden in vorgeschriebener Länge abschneiden
2. Pfeile auf der Oberseite des Fadenkopf so stellen, dass diese direkt über den Fadenführun
gen stehen (sieh Bild).
3. Ein Ende des Nylonfadens durch eine Fadenführung und durchzeihen, bis der Nylonfaden auf beiden Seiten gleich lang ist.
4. Oberteil des Fadenkopfs festhalten während Sie das Unterteil im Uhrzeigersinn (rechts) drehen. So lange drehen, bis auf jeder Seite noch etwa 13 cm Faden herausschauen.
Der Fadenkopf ist jetzt geladen und einsatzbereit.
ITALIANO
Capacità totale filo testina per bordatore 375 LH 0,080 (2,0 mm) dia. – 10’ (3 m)
Caricamento del filo
0,095 (2,4 mm) dia. – 10’ (3 m)
1. Tagliare un pezzo di filo della lunghezza indicata.
2. Allineare le frecce sul pomello con le aperture degli occhielli.
3. Inserire un’estremità del filo in un occhiello e spingerlo verso l’esterno in modo da ottenere una lunghezza uguale su entrambi i lati.
4. Tenere ferma la testina del bordatore e girare il pomello in senso orario per avvolgere il filo sulla bobina, lasciando esposti circa 5” (13 cm) di filo su ciascun lato.
La testina del bordatore è ora carica e pronta per essere utilizzata.
español
Hilo total capacidad de la cabeza de recortadora 375 LH
Carga del hilo de la recortadora
.080 (2.0 mm) dia. – 10’ (3 m)
.095 (2.4 mm) dia. – 10’ (3 m)
1.Corte un pedazo de hilo a la longitud recomendada.
2.Alinee las flechas de la parte superior de la perilla con las aberturas en los ojales.
3.Inserte un extremo del hilo de la recortadora en un ojal, y empuje el hilo una misma distancia por la cabeza de la recortadora.
4.Sujete la cabeza de la recortadora mientras gira la perilla hacia la derecha en el carrete hasta que queden al descubierto unos 13 cm (5”) de cada hilo.
La cabeza de la recortadora está ahora completamente cargada y lista para la operación.
6
NO.
PART NUMBER
1
X473000011
SPOOL LH
DESCRIPTION
2
V160000060
3
E415000091
4
BESCHREIBUNG
NOM DE LA PIÈCE
BOBINE LH
DESCRIZIONE
DESCRIPCIÓN
BOBINA LH
BUSHING M10X1.25 BAGUE M10X1.25
ADAPTER M10X1,25
BOCCOLA M10X1.25 BUJE M10X1.25
KNOB
POIGNÉE
DECKEL, FADENKOPF
POMELLO
PERILLA
1
X476000021
CORE
MOYEU
INNENTEIL
ASSE CENTRALE
BASE CENTRAL
1
5
X470000181
EYELET CARRIER
CORP DE POULIE
HALTER,
FADENFÜHRUNGEN
COMPARTO
OCCHIELLI
SOPORTE DE
BOQUILLAS
1
6
X475000050
EYELET
PASSE-CÃBLE
FADENFÜHRUNG
OCCHIELLO
BOQUILLAS
2
7
X494000280
CAP
CAPUCHON
KNOPF
TAPPO
TAPA
1
8
V450000871
SPRING
RESORT
FEDER
MOLLA
RESORTE
1
9
X472000012
COVER
COUVERCLE
GEHÄUSE, UNTERTEIL
COPERCHIO
TAPA
1
PERNO, 7MM LH
PERNO, 7MM LH
1
PERNO, 8MM LH
PERNO, 8MM LH
1
BOCCOLA M10X1
BUJE M10X1
1
STEHBOLZEN 7 MM,
LINKSGEWINDE
STEHBOLZEN 8 MM,
LINKSGEWINDE
CARRETE LH
QTY.
FADENSPULE
1
1
10
V216000070
STUD, 7MM LH
BOULON, 7MM LH
11
V225000240
STUD, 8MM LH
BOULON, 8MM LH
12
V160000070
BUSHING M10X1
BAGUE M10X1
ADAPTER M10 X 1
13
V160000080
BUSHING M8X1.25
BAGUE M8X1.25
ADAPTER M8 X 1,25
BOCCOLA M8X1.25
BUJE M8X1.25
1
14
V160000120
BUSHING 10X1.25
BAGUE 10X1,25
ADAPTER 10X1,25
BOCCOLA 10X1,25
BUJE 10X1,25
1
15
V376001850
SPACER
ENTRETOISE
ABSTANDHALTER
DISTANZIATORE
ESPACIADOR
1
Speed-Feed® Trimmer Head Mounting Stud Selection Chart
Ableau de sélection du goujon de montage de tête de coupe de taille-bordures Speed-Feed®
Auswahltabelle zur anpassung des Speed-Feed® fadenkopfs
Tabella di selezione perni di montaggio per testina bordatore Speed-Feed®
Cuadro de selección de espárragos de montaje de la cabeza de recortadora Speed-Feed®
Shaft Size
Diamètre Arbre
Wellendurchmesser
Dimensioni Albero
Tamaño de Eje
Mounting Stud
Goujon de Montage
Stehbolzen
Perno di Montaggio
Espárrago de Montaje
PART NUMBER
RÉF.
ARTIKELNUMMER
CODICE RICAMBIO
N/P
8 mm LH
Silver (Argent) (Silber)
(Argento) (Plata)
V225000240
10 mm
8 mm
10 mm
7 mm
7 mm LH
(Gold) (Or) (Gold), (Oro), (Oro)
V216000070
15
2,12,13,14
NOTE: Trimmer head is pre-wound with .095"
(2.4mm) Crossfire™ trimmer line.
REMARQUE : Une ligne Crossfire™ de
2,4 mm (0,095”) a été pré-enroulée sur la tête
de coupe du taille-bordures.
ANMERKUNG: Der Fadenkopf ist werksseitig
mit 2,4 mm Crossfire™ Nylonfaden ausgerüstet.
NOTA: La testina del bordatore è fornita già
dotata di filo Crossfire™ da 0,095” (2,4 mm).
NOTA: La cabeza de la recortadora está enrollada de antemano con un hilo de recortadora
de 2.4 mm (0.095”) Crossfire™.
IMPORTANT! When the wear indicators located at the bottom of the Speed-Feed® head are worn smooth, replacement of the
cover or the entire Speed-Feed® head is required.
IMPORTANT! Lorsque les indicateurs d’usure placés sous la tête Speed-Feed® sont complètement usés, il faut remplacer la totalité de la tête.
WICHTIG! Wenn die Verschleißanzeige am Boden des Fadenkopf sabgenutzt ist, muss der Gehäuse-boden erneuert, oder der
Fadenkopf gewechselt werden.
IMPORTANTE! Quando gli indicatori di usura posti sul fondo della testina a filo Speed-Feed® sono consumati e lisci, si richiede la sostituzione della copertura o dell’intera testina a filo Speed-Feed®.
¡IMPORTANTE! Cuando los indicadores de desgaste ubicados en la parte inferior de la cabeza Speed-Feed® estén lisos por el
desgaste, será necesario reemplazar la cubierta o toda la cabeza Speed-Feed®
Wear Indicators
Indicateurs d’usure
Verschleißanzeige
Indicatori di usura
Indicadores de desgaste
Wear Indicators
Indicateurs d’usure
Verschleißanzeige
Indicatori di usura
Indicadores de desgaste
7
Speed-Feed®
REF#
REF#
ECHO
GT Series: 100, 140, 160, 200, 251, 1000, 1100, 2000, 2100, 2101, REF#
ECHO
RH1
2102, 2103, 2200, 2301, 2400
GT Series: 100, 140, 160, 200, 251, 1000, 1100, 2000, 2100, 2101,
ECHO
RH1
SRM
140, 200,
202,
210, 220, 230, 250, 251, 260, 261,
2102,SERIES:
2103, 2200,
2301,
2400
REF#
265,Series:
280, 300,
343,
350,2000,
400,2100,
402, 500,
GT
100,302,
140,303,
160,311,
200,330,
251,340,
1000,
1100,
2101,
SRM 1500,
SERIES:
140,2010,
200, 202,
210,
220,2110,
230,2200,
250, 251,
260,
261,2301,
RH1
501,
1501,
2090,
2100,
2201,
2300,
LH6
2102,
2103, 2200, 2301, 2400
ECHO
265,
300,
302,2500,
303, 311,
340,
343,2530,
350, 2601,
400, 402,
500,
REF#
2400,280,
2410,
2450,
2501,330,
2502,
2510,
3000,
SRM
SERIES:
140,
200,
202,
210,
220,
230,1100,
250,
251,
260,
261,
GT
Series:
100,
140,
160,
200,
251,
1000,
2000,
2100,
2101,
501,
1500,
1501,
2010,
2090,
2100,
2110,
2200,
2201,
2300,
2301,
LH6
3001,
3010,
3100,
3110,
3400,
3410,
3500,
3550,
3800,
4600
RH1
265,
300,
302,2301,
303, 311,
340,
343,2530,
350, 2601,
400, 402,
500,
2102,
2103,
2200,
2400
ECHO
2400,280,
2410,
2450,
2500,
2501,330,
2502,
2510,
3000,
501,
1500,
1501,
2010,
2090,
2100,
2110,
2200,
2201,
2300,
2301,
3001,
3010,
3100,
3110,
3400,
3410,
3500,
3550,
3800,
4600
LH6
SRM
SERIES:
140,
200,
202,
210,
220,
230,1100,
250,
251,
260,
261,
GT
Series:
100,
140,
160,
200,
251,
1000,
2000,
2100,
2101,
2400, 2410, 2450, 2500, 2501, 2502, 2510, 2530, 2601, 3000,
RH1
265,
280,
300,
302,2301,
303, 311,
2102,
2103,
2200,
2400330, 340, 343, 350, 400, 402, 500,
HOMELITE
3001, 3010, 3100, 3110, 3400, 3410, 3500, 3550, 3800, 4600
501, 1500, 1501, 2010, 2090, 2100, 2110, 2200, 2201, 2300, 2301,
LH6
SRM
SERIES:
140, 200,
202, 210,1/1/86),
220, 230,
250,(to
251, 260, 261,
HK-24
(to 1/1/’86),
HK30(after
HK33
2400, 2410,
2450, 2500,
2501, 2502, 2510,
2530, 1/1/86)
2601, 3000,
HOMELITE
LH2
265, 280, 300, 302, 303, 311, 330, 340, 343, 350, 400, 402, 500,
3001, 3010, 3100, 3110, 3400, 3410, 3500, 3550, 3800, 4600
501,
1500,
1501,BCH32,
2010,
2090,
2100,
2110,
2200,
2300,
2301,
HK-24
(to
1/1/’86),
HK30(after
1/1/86),
HK33
(to2201,
1/1/86)
BCH20,
BCH24,
BCH33,
BCH40,
BCH48,
HBC-30,
HBC-38,
LH6
LH2
HOMELITE
2400, 2410,
2501,
2502,HK24(after
2510, 2530,
2601, 3000,
HK-15,
HK 182450,
(after2500,
1/1/86),
HK-28,
1/1/86),
HK-25,
BCH20,
BCH24,
BCH32,
BCH33,
BCH40,
BCH48,
HBC-38,
HK-24
(to
1/1/’86),
HK30(after
1/1/86),
HK33
(toHBC-30,
1/1/86)
3001, 3010,
3110,
3400, 3410,
3500,
3550,
3800, 4600
HK-30
(up
to3100,
1/86),
HK-33(after
1/1/86),
HK-38,
PBC-3600,
PBCLH4
LH2
HK-15,
HK
18
(after
1/1/86),
HK-28,
HK24(after
1/1/86),
HK-25,
HOMELITE
3800,
PBC-4000, PBC-4000, PLT3400, ST-285, ST155, ST175,
BCH20,
BCH24,
BCH32,
BCH33, BCH40,
HBC-38,
HK-30 (up
to 1/86),
HK-33(after
1/1/86),BCH48,
HK-38, HBC-30,
PBC-3600,
PBCLH4
ST385,
ST485
HK-24PBC-4000,
(to
HK30(after
1/1/86),
HK33 (to
1/1/86)
HK-15,
HK1/1/’86),
18 (after
1/1/86), PLT3400,
HK-28,
HK24(after
1/1/86),
HK-25,
LH2
3800,
PBC-4000,
ST-285,
ST155,
ST175,
HOMELITE
FK514,
NBA524,
PMB522,
SX040,1/1/86),
SXD40,TXD508
HK-30
(up
to 1/86),
HK-33(after
HK-38, PBC-3600, PBCST385,
LH3
LH4
BCH20,ST485
BCH24, BCH32, BCH33, BCH40, BCH48, HBC-30, HBC-38,
3800,
PBC-4000,
PBC-4000,
PLT3400,
ST-285,
ST155,
ST175,
HK-24
1/1/’86),
HK30(after
1/1/86),
HK33 (to
1/1/86)
HK-15,(to
HK
18 (after
1/1/86),
HK-28,
HK24(after
1/1/86),
HK-25,
LH2
FK514,
NBA524,
PMB522,
SX040,
SXD40,TXD508
HBC40,
PBC3800,
PBC4000,
PMB52,
HBC48
LH3
LH6
ST385, ST485
HK-30 (up to 1/86), HK-33(after 1/1/86), HK-38, PBC-3600, PBCLH4
BCH20,
BCH24,
BCH32,
BCH33,
BCH40,
BCH48,
HBC-30,
HBC-38,
HBC40,
PBC3800,
PBC4000,
PMB52,
HBC48
HBC20,
HBC24,
HBC32C,
HBC33,
ST200,
ST360,ST155,
ST80, SXD20,
FK514,
NBA524,
PMB522,
SX040,
SXD40,TXD508
3800, PBC-4000,
PBC-4000,
PLT3400,
ST-285,
ST175,
LH6
LH3
RH2
HK-15,
HK
18
(after
1/1/86),
HK-28,
HK24(after
1/1/86),
HK-25,
TK518, ST485
RK521, ST100, ST120, ST155, ST175CG
ST385,
HK-30
to 1/86),
HK-33(after
1/1/86),
HK-38, ST80,
PBC-3600,
PBCHBC20,(up
HBC24,
HBC32C,
HBC33,
ST200,
ST360,
SXD20,
LH4
HBC40,
PBC3800,
PBC4000,
PMB52,
HBC48
LH6
RH2
ST80/100/120/160/180/200/210/360/385
(EURO)
FK514,
NBA524,
PMB522,
SX040,
SXD40,TXD508
3800,
PBC-4000,
ST-285, ST155, ST175,
TK518,PBC-4000,
RK521, ST100,
ST120,PLT3400,
ST155, ST175CG
LH2
LH3
HBC20,ST485
HBC24, HBC32C, HBC33, ST200, ST360, ST80, SXD20,
ST385,
ST80/100/120/160/180/200/210/360/385
(EURO)
ST20/40/60/100/200/400,
SXD20, RK521,
TK518
RH2
HBC40,RK521,
PBC3800,
PBC4000,
LH2
LH4
TK518,
ST100,
ST120,PMB52,
ST155, HBC48
ST175CG
LH6
FK514, NBA524, PMB522, SX040, SXD40,TXD508
LH3
ST20/40/60/100/200/400,
SXD20,ST200,
RK521,ST360,
TK518
ST80/100/120/160/180/200/210/360/385
(EURO)
HBC20, HBC24, HBC32C, HBC33,
ST80, SXD20,
LH4
LH2
RH2
HBC40,
PBC3800,
PBC4000,
TK518, RK521,
ST100,
ST120,PMB52,
ST155, HBC48
ST175CG
LH6
ST20/40/60/100/200/400,
SXD20, RK521, TK518
HONDA
LH4
ST80/100/120/160/180/200/210/360/385
(EURO)
HBC20,
HBC24, HBC32C, HBC33, ST200, ST360,
ST80, SXD20,
LH2
RH2
UMK422LNA/LTA,
UMK431LNA/TA/UNBA,
HHT25SLTAT, HHTHONDA
TK518,
RK521, ST100,
ST120, ST155, ST175CG
LH6
ST20/40/60/100/200/400,
SXD20, RK521, TK518
35SLTAT,
HHT35SUKAT
LH4
UMK422LNA/LTA, UMK431LNA/TA/UNBA, (EURO)
HHT25SLTAT, HHTST80/100/120/160/180/200/210/360/385
LH2
HONDA
LH6
35SLTAT, HHT35SUKAT
ST20/40/60/100/200/400,
SXD20,
RK521,
TK518
UMK422LNA/LTA, UMK431LNA/TA/UNBA, HHT25SLTAT, HHTLH4
LH6
HUSQVARNA
35SLTAT,
HHT35SUKAT
HONDA
(UP
TO
86)16R,
22R,
24R,
25RL
UMK422LNA/LTA,
UMK431LNA/TA/UNBA,
HHT25SLTAT,
HHTHUSQVARNA
LH2
LH6
35SLTAT,
HHT35SUKAT
HONDA
(UP TO 86)16R,
22R, 24R, 25RL
24R(up
to ser #603702)
LH2
LH1
HUSQVARNA
UMK422LNA/LTA, UMK431LNA/TA/UNBA, HHT25SLTAT, HHTLH6
24R(up
toHHT35SUKAT
ser 32LC,
#603702)
26LC,
MONDO
(UP
TO26RLC,
86)16R,
22R,32RLC,
24R, 25RL
LH1
RH1
35SLTAT,
LH2
HUSQVARNA
26LC, 125L,
26RLC,
32LC,
32RLC,225R,
MONDO
122L,
225L,
225LD,
225RD, 225RJ, 227LD, 232L,
24R(up
to ser
#603702)
RH1
LH1
LH6
(UP TO322L,
86)16R,
22R,
24R, 25RL
232R,
322R,
324LX,
325LX/RX, 326LS/LX, 335LS
LH2
122L,
125L,
225LD,
225RD, 225RJ, 227LD, 232L,
26LC,
26RLC,225L,
32LC,
32RLC,225R,
MONDO
HUSQVARNA
RH1
LH6
24R(up322L,
to ser
#603702)
232R,
322R,
324LX, 325LX/RX, 326LS/LX, 335LS
LH1
(UP TO125L,
86)16R,
22R,
24R, 25RL
122L,
225L,
225LD,
225R, 225RD, 225RJ, 227LD, 232L,
LH2
LH6
26LC,
26RLC,322R,
32LC,324LX,
32RLC,325LX/RX,
MONDO 326LS/LX, 335LS
JONSERED
232R, 322L,
RH1
24R(up to ser #603702)
LH1
BP40,
BP40COMBI,
BP2040,
BR400,
BR420,
BR450,
BR460,
122L,
125L,
225L, 225LD,
225R,
225RD,
225RJ,
227LD,
232L,
JONSERED
LH6
26LC,
26RLC,
32LC,
32RLC,
MONDO
BR480,
BR500,
Tiger
40, GT21L,
GT22L,
GT24L, GR26COMBI,
232R, 322L,
322R,
324LX,
325LX/RX,
326LS/LX,
335LS
RH1
LH2
BP40,
BP40COMBI,
BP2040,
BR400,
BR420,
BR450,
BR460,
GR26D,
GR26L, GR32L, GR2026CL, GR2026D, LR200, LR220,
JONSERED
122L,
225L,
225LD,
225R,
225RD,
225RJ, 227LD,
232L,
BR480,125L,
BR500,
Tiger
40,
GT21L,
GT22L,
GT24L,
GR26COMBI,
LR260,
LR320,
LR400,
LR420,
LR450,
LR460
LH6
LH2
BP40,
BP40COMBI,
BP2040,
BR400,GR2026D,
BR420, BR450,
BR460,
232R,
322L,
322R,
324LX,
325LX/RX,
326LS/LX,
335LS
GR26D,
GR26L,
GR32L,
GR2026CL,
LR200,
LR220,
RS38ANCIEN,
BR480,
BR500,
Tigerolder
40,
GT21L,
GT22L,
GT24L, GR26COMBI,
JONSERED
LR260, LR320,RS38
LR400,
LR420,
LR450,
LR460
LH5
LH2
GR26D, GR26L, GR32L, GR2026CL, GR2026D, LR200, LR220,
BP40, BP40COMBI,
RS38ANCIEN,
RS38 BP2040,
older BR400, BR420, BR450, BR460,
GT25L,
GT26, GT26L
LH5
RH1
LR260, LR320, LR400, LR420, LR450, LR460
BR480,
BR500, Tiger 40, GT21L, GT22L, GT24L, GR26COMBI,
JONSERED
LH2
GT25L,
GT26,
GT26L
RS44,
GR44,
GR41,
J40D,
KQ20/30 (EURO)
RS38ANCIEN,
RS38
older
GR26D,
GR26L,
GR32L,
GR2026CL,
GR2026D, LR200, LR220,
RH1
LH6
LH5
BP40, BP40COMBI, BP2040, BR400, BR420, BR450, BR460,
LR260, LR320, LR400, LR420, LR450, LR460
BR480,
BR500,
TigerJ40D,
40, GT21L,
GT22L,
GT24L, GR26COMBI,
RS44, GR44,
KQ20/30
(EURO)
GT25L,
GT26,GR41,
GT26L
LH6
RH1
LH2
RS38ANCIEN,
older
GR26D,
GR26L,RS38
GR32L,
GR2026CL, GR2026D, LR200, LR220,
LH5
RS44,
GR44,
GR41,
J40D,
KQ20/30
(EURO)
MARUYAMA
LR260,
LR320,
LR400,
LR420,
LR450,
LR460
LH6
GT25L, GT26, GT26L
RH1
BC184,
BC184C,
BC200,
RS38ANCIEN,
RS38
olderBC201, BC230, BC241, BC260, BC260H,
MARUYAMA
LH5
RS44, GR44,
GR41,
J40D,BC326,
KQ20/30
(EURO) BC402, BC420H,
BC310,
BC320,
BC320H,
BC340DL,
LH6
BC184, GT26,
BC184C,
BC200,
BC230,
BC241,
BC260,
BC260H,
GT25L,
GT26L
RH1
BC500,
BC500H,
BC2300,BC201,
BC2321,
BC2600,
BC3021,
BC3200,
LH2
MARUYAMA
BC310,
BC320,
BC320H,
BC326,
BC340DL,
BC402,BCL2250C,
BC420H,
BC4200H,
BCL2550,
BCGX22,
BCGX31,
BCL2250,
RS44,
GR44,
GR41,
J40D,
KQ20/30
(EURO)
BC184,
BC184C,
BC200,
BC201,
BC230,
BC241,
BC260,
BC260H,
LH6
BC500, MC-5,
BC500H,
BC2300, BC2321, BC2600, BC3021, BC3200,
LH2
BST23,
NC8
BC310,
BC320,
BC320H,
BC326,
BC340DL,
BC402,BCL2250C,
BC420H,
MARUYAMA
BC4200H,
BCL2550,
BCGX22,
BCGX31,
BCL2250,
BC220DL,
BC221DL
BC500,
BC500H,
BC2300, BC2321, BC2600, BC3021, BC3200,
BST23,
NC8
LH1
LH2
BC184, MC-5,
BC184C,
BC200, BC201, BC230, BC241, BC260, BC260H,
BC4200H, BCL2550, BCGX22, BCGX31, BCL2250, BCL2250C,
BC310,
BC320,
BC320H, BC326, BC340DL, BC402, BC420H,
MARUYAMA
BC220DL,
BC221DL
LH1
BST23, MC-5, NC8
BC500, BC500H, BC2300, BC2321, BC2600, BC3021, BC3200,
LH2
BC184, BC184C, BC200, BC201, BC230, BC241, BC260, BC260H,
BC220DL,
BC4200H, BC221DL
BCL2550, BCGX22, BCGX31, BCL2250, BCL2250C,
LH1
BC310, BC320, BC320H, BC326, BC340DL, BC402, BC420H,
BST23, MC-5, NC8
BC500, BC500H, BC2300, BC2321, BC2600, BC3021, BC3200,
LH2
BC220DL, BC221DL
BC4200H,
BCL2550, BCGX22, BCGX31, BCL2250, BCL2250C,
LH1
BST23, MC-5, NC8
BC220DL, BC221DL
LH1
ECHO Incorporated.
400 Oakwood Road
Lake Zurich, IL 60047-1564 U.S.A.
Telephone: 1-800-432-3246
www.speedfeedhead.com
Copyright© 2011 By Echo, Incorporated
All Rights Reserved.
Speed-Feed® Trimmer Head Application Chart
Tableau D’Application De La Tete
Anwendungstabelle
REF#
MARUYAMATabella
(continued)
REF#
di applicazione
testina del bordatore
BT17, BT220, BC200C, BC260C
LH4
MARUYAMA
(continued)
Tabla
De
Aplicaciones
BC184C,
BC200C,
BC260C
BT17, BT220, BC200C, BC260C
LH6
LH4 De Cabezales
BC201C
BC184C, BC200C, BC260C
MARUYAMA
(continued)
BC430DWM,
BC440DWM, 32,
35, BC500
BC201C
BT17, BT220, BC200C, BC260C
BC430DWM, BC440DWM, 32,
35, BC500
MARUYAMA
(continued)
BC184C,
BC200C,
BC260C
BT17,
BT220,
BC200C,
BC260C
McCULLOCH
BC201C
BC184C,
BC200C,
BC260CMAC85, MAC2825, MAC2827, PROMAC
70, 75, 80,
85, MAC100A,
McCULLOCH
SER:
I-SX, II, II BC440DWM,
SUP, IV, HD, 2320L,
2045, 138, SEB I-SX
BC430DWM,
32, 35,2035,
BC500
BC201C
70,
75,
80,
85,
MAC100A,
MAC2827,
PROMAC
SPECIAL, SEB II-S, SEB III-S,MAC85,
SILVER MAC2825,
EAGLE 28, SILVER
EAGLE
SER:SUPER
I-SX, II,EBI-S,
IIBC440DWM,
SUP,TITAN;
IV, HD,2100,
2320L,
2035,
2045,
138, SEB I-SX
32,
2200,
2510,
ROADRUNNER
BC430DWM,
32, 35,
BC500
SPECIAL, SEB II-S, SEB III-S, SILVER EAGLE 28, SILVER EAGLE
MAC57,
MAC90,
MAC95,2100,
MAC100A
MARUYAMA
(continued)
32, SUPER
EBI-S, TITAN;
2200, 2510, ROADRUNNER
McCULLOCH
BT17,
BC260C
PROMAC
SERIES:
III, IIISUP,
IVSUP, PROSCAPER;
SERIES: 28S,
MAC57,
MAC90,
MAC95,
MAC100A
70,
75,BT220,
80,
85,BC200C,
MAC100A,
MAC85,
MAC2825, MAC2827,
PROMAC
McCULLOCH
32H,
32HDS,
IV, V,
II, IIHD,
SEBIC,
SER: I-SX,
II, IIIII
SUP,
IV,IS,
HD,
2320L,
2035,SUPMAC100A;
2045, 138, SEBPS1,
I-SXPS2,
BC184C,
BC200C,
BC260C
PROMAC
SERIES:
III,
IIISUP,
IVSUP,III,MAC2825,
PROSCAPER;
SERIES:
28S,
PS3,
PS4,
PS5,
SEBIV;
EB
SERIES:
IVSL,
3,
4,
3SX,
32BCS,
70,
75,
80,
85,
MAC100A,
MAC85,
MAC2827,
PROMAC
SPECIAL, SEB II-S, SEB III-S, SILVER EAGLE 28, SILVER EAGLE
32H,
32HDS,
IV, V,
II, 2320L,
IIHD, SEBIC,
SUPMAC100A;
35L,
280,
282,
285BCS,
297BCS,
325BC,
327BC,
2815,
2816
2817,
SER:
I-SX,
II,EBI-S,
II III
SUP,
IV,IS,
HD,
2035,
2045,
138,
SEBPS1,
I-SXPS2,
32, SUPER
TITAN;
2100, 2200,
2510,
ROADRUNNER
BC201C
PS3, PS4, SEB
PS5,II-S,
SEBIV;
SERIES:
III,EAGLE
IVSL, 3,28,
4, SILVER
3SX, 32BCS,
2818,
SPECIAL,
SEBEB
III-S,
SILVER
EAGLE
MAC57,
MAC90,
MAC95,
MAC100A
35L,
280,
282,
285BCS,
297BCS,
325BC,
327BC,
2815,
2816
2817,
BC430DWM,
BC440DWM,
32,30AV,
35, BC500
32,
SUPER
EBI-S,
TITAN;
2100,
2200,
2510, ROADRUNNER
MAC
22/23/30A,
SUPERMAC
MS33,
DELTA,
38AV,
MS40,
2818,
PROMAC
SERIES:MAC95,
III, IIISUP,
IVSUP, PROSCAPER; SERIES: 28S,
BP30AV,MAC90,
TD2400/3300/4000
MAC57,
MAC100A
MAC
22/23/30A,
MS33,
DELTA, 38AV,
MS40,
32H, 32HDS,
III IV,SUPERMAC
V, IS, II, IIHD,30AV,
SEBIC,
SUPMAC100A;
PS1,
PS2,
MAC
57, MAC
90,III,
MAC
95, IVSUP,
MAC 100A,
MAC 32,SERIES:
MAC 3728S,
BP30AV,
PROMAC
SERIES:
IIISUP,
PS3,
PS4,TD2400/3300/4000
PS5, SEBIV;
EB SERIES:
III,PROSCAPER;
IVSL, 3, 4, 3SX,
32BCS,
McCULLOCH
32H,
32HDS,
III
IV,
V,
IS,
II,
IIHD,
SEBIC,
SUPMAC100A;
PS1,
PS2,
35L,
280,
282,
285BCS,
297BCS,
325BC,
327BC,
2815,
2816
MAC 57, MAC 90, MAC 95, MAC 100A, MAC 32, MAC 37 2817,
70,
75,
80,PS5,
85, MAC100A,
MAC85,
MAC2827,
PS3,
PS4,
SEBIV; EB SERIES:
III,MAC2825,
IVSL, 3, 4, 3SX,
32BCS,PROMAC
2818,
SER:
I-SX,
II, II SUP,
IV, HD,
2320L,325BC,
2035, 2045,
138,
SEB2816
I-SX 2817,
35L,
282,
285BCS,
297BCS,
327BC,
2815,
RED280,
MAX
MAC
22/23/30A,
30AV,EAGLE
MS33,28,
DELTA,
38AV,
MS40,
SPECIAL,
SEB II-S,SUPERMAC
SEB III-S, SILVER
SILVER
EAGLE
2818,
BP30AV,
TD2400/3300/4000
BC220DL,
BC221DL,
BC300DL,
BC2300DL,
BK235FL,
BK345FL,
32,
SUPER
EBI-S,
TITAN;
2100,
2200,
2510,
ROADRUNNER
RED
MAX
MAC
22/23/30A,
SUPERMAC
30AV,
MS33,
DELTA,
38AV,
MS40,
BK435FL,
BK530DL,
BC17,
BC23,
BC32, MAC
BC240DL
MAC 57,MAC90,
MAC
90,MAC95,
MAC
95,MAC100A
MAC 100A,
32, MAC 37
MAC57,
BP30AV,
TD2400/3300/4000
BC220DL,
BC221DL,
BC300DL,
BC2300DL, BK235FL, BK345FL,
BC260DL,BK530DL,
BC261DL,BC17,
BC262DL,
BC340DL,
BC341DL, BC342DL,
BK435FL,
BC23,
BC32,MAC
BC240DL
MAC
57, MAC
90, III,
MAC
95,
MAC
32,SERIES:
MAC
3728S,
PROMAC
SERIES:
IIISUP,
IVSUP,100A,
PROSCAPER;
BC2600DL,
BC430DWM,
BC440DWM,
BK346FL,
BK245FLK,
BC260DL,
BC261DL,
BC262DL,
BC340DL,
BC341DL, BC342DL,
32H,
32HDS,
III IV, V,BC260DM/DMU,
IS,
II, IIHD, SEBIC,
SUPMAC100A;
PS1,
PS2,
BK436FL,
BC245A,
BC340DWM/FW,
BC431DWM,
RED
MAX
BC2600DL,
BC430DWM,
BC440DWM,
BK346FL,
PS3,
PS4,
PS5,
SEBIV;
EB SERIES:
III, IVSL,
3, 4, 3SX,BK245FLK,
32BCS,
BCD20,
BCF01,
BC2601S,
BC3400DW,
BC4400DW,
BCX2600DS,
BK436FL,
BC245A,
BC260DM/DMU,
BC340DWM/FW,
BC431DWM,
35L,
280, 282,
285BCS,
297BCS,BC2300DL,
325BC,
327BC,
2815, BK345FL,
2816
2817,
BC220DL,
BC221DL,
BC300DL,
BK235FL,
BCZ2500S/SU/SW
RED
BCD20,MAX
BCF01,
BC2601S,
2818,
BK435FL,
BK530DL,
BC17,BC3400DW,
BC23, BC32,BC4400DW,
BC240DL BCX2600DS,
BC430DWM,
BC440DWM,
BC441DWM,
BC442DWM,
BC531DWM,
BCZ2500S/SU/SW
BC220DL,
BC221DL,
BC300DL,
BC2300DL,
BK235FL,
BK345FL,
MAC
22/23/30A,
SUPERMAC
30AV,
MS33,
DELTA,
38AV,
MS40,
BC260DL, BC261DL,
BC262DL,
BC341DL, BC342DL,
BC532DWM,
FBC22,BC17,
FBC26BC23,BC340DL,
BK435FL,
BK530DL,
BC32, BC240DL
BC430DWM,
BC440DWM,BC440DWM,
BC441DWM,
BC442DWM,
BC531DWM,
BP30AV,
TD2400/3300/4000
BC2600DL,
BC430DWM,
BK346FL,
BK245FLK,
BC200,
BC2000DL,
BT2000,
BC532DWM,
FBC22,
FBC26 BT2001DL
BC260DL,
BC261DL,
BC262DL,
BC341DL,
BK436FL,
BC245A,
BC260DM/DMU,
BC340DWM/FW,
BC431DWM,
MAC
57, MAC
90, MAC
95, MACBC340DL,
100A,
MAC
32, MACBC342DL,
37
BC2600DL,
BC430DWM,
BC440DWM,
BK346FL,
BK245FLK,
BCD20,
BCF01,
BC2601S,
BC3400DW,
BC4400DW,
BCX2600DS,
BC200, BC2000DL, BT2000, BT2001DL
BK436FL,
BC245A, BC260DM/DMU, BC340DWM/FW, BC431DWM,
BCZ2500S/SU/SW
SHINDAIWA
BCD20,
BCF01, BC2601S, BC3400DW, BC4400DW, BCX2600DS,
SHINDAIWA
BC430DWM,
BC440DWM,
BC441DWM,
BC442DWM,
BC531DWM,
22T,
C230,
C242,
C2510,
T195s, T220,
T222,T230,
T230s,
BCZ2500S/SU/SW
RED
MAX
BC532DWM,
FBC22,
FBC26
SHINDAIWA
T195,
T220,
T222,
T230,
T230s, T242, T242X, T2510, T2510X
SHINDAIWA
T242,
T242X,
T2510,
T2510X
BC430DWM,
BC440DWM,
BC441DWM,
BC442DWM,
BC531DWM,
BC220DL,
BC221DL,
BC300DL,
BC2300DL,
BK235FL,
BK345FL,
22T,
C230,
C242,
C2510,
T195s,
T220,
T222,T230,
T230s,
BC200,T261,
BC2000DL,
BT2000,T272,
BT2001DL
T260,
T261B/XR/XB,
T272X,
T282,
T282X,
T300,
BC532DWM,
FBC22,
FBC26
T195,
T220,
T222,
T230,
T230s,
T242,
T242X,
T2510,
T2510X
C3410,
C260,
T260,
T261,
T261B/XR/XB,
T270, T272,
BK435FL,
BK530DL,
BC17,
BC23,
BC32, BC240DL
T242,
T242X,
T2510,
T2510X
T3410, T3410X,
T350 T3410, T3410X, T350
T272X,
T282,
T300,
BC200,
BC2000DL,
BT2000,
BT2001DL
BC260DL,
BC261DL,
BC262DL,
BC340DL,
BC341DL,
BC342DL,
T260, T261,
T261B/XR/XB,
T272,
T272X, T282,
T282X,
T300,
C3410,
C260,
T260,
T261,
T261B/XR/XB,
T270,
T272,
BP35,
B450,
C350
BC2600DL,
BC430DWM,
BC440DWM, BK346FL, BK245FLK,
T3410,B45,
T3410X,
T350
BP35,
B45,
B450,
C350
SHINDAIWA
T272X,
T282,
T300,
T3410, T3410X, T350
SHINDAIWA
BK436FL,
BC245A,
BC260DM/DMU,
BC340DWM/FW,
BC431DWM,
22T,
C230,
C242,
C2510,
T220, T222,T230, T230s,
F18,
F21,
F22,
F230,
F195T195s,
BP35,F20,
B45,
B450,
C350
F18,
F21,
F22,
F230,
F195s,
22F T2510,
BCD20,
BCF01,
BC2601S,
BC3400DW,
BC4400DW,
BCX2600DS,
BP35,
B45,
B450,
C350
T195,F20,
T220,
T222,
T230,
T230s,
T242, T242X,
T2510X
SHINDAIWA
T242,
T242X,
T2510,
T2510X
SHINDAIWA
BCZ2500S/SU/SW
F18, F20,
F21,
F22,
F230,
F195
22T,
C230,
C242,
C2510,
T195s,
T220,
T222,T230, T230s,
F18,
F20,
F21,
F22,
F230,
F195s,
22F
T260,
T261,
T261B/XR/XB,
T272,
T272X,
T282,
T282X,
T300,
C3410,
C260,
T260,
T261,
T261B/XR/XB,
T270,
T272,
T195,
T220,
T222,
T230, T2510X
T230s,
T242, T242X,
T2510, T2510X
BC430DWM,
BC440DWM,
BC441DWM,
BC442DWM,
BC531DWM,
T242,
T242X,
T2510,
T3410, T3410X,
T350 T3410, T3410X, T350
T272X,
T282,
T300,
STIHL
BC532DWM,
FBC22,
FBC26
T260,
T261,
T261B/XR/XB,
T272,
T272X, T282, T282X,
T300,
C3410,
C260,
T260,
T261,
T261B/XR/XB,
T270,
T272,
BP35,
B45,
B450,
C350
FS50, FS51,
FS55,
FS60,
FS61,
FS65,
FS80,T350
FS83, FS85, FS86,
BP35,
B45,
B450,
C350
T3410,
T3410X,
T350
BC200,
BC2000DL,
BT2000,
BT2001DL
T272X,
T282,
T300,
T3410,
T3410X,
STIHL
FS90,
FS91,
FS96
F18, F20,
F21,
F22,
F230,
F195
BP35,
B45,
C350
F18,
F21,
F22,
F230,
22FFS83, FS85, FS86,
FS50,F20,
FS51,
FS55,
FS60,
FS61, F195s,
FS65, FS80,
BP35,
B45,B450,
B450,
C350
FS66,
FS74,
FS76,
FS81,
FS83,
FS85,
FS86,
FS100, FS106, FS108,
FS90,F20,
FS91,
FS96
F18,
F21,
F22,
F230,
F195
FS110,
FS130,
FS250,
FS40,
FS44,
FS45,
FS46, FS48, FS52, FS56,
SHINDAIWA
F18,
F20,
F21,
F22,
F230,
F195s,
22F
SHINDAIWA
FS66,
FS74,
FS76,
FS81,
FS83,
FS85,
FS86,
FS100,
FS106, FS108,
FS62,
FS66,
FS85,
FS86,
FS88,
FS96,
FS106,
FS108,FS120,
FS200,
22T,
C230, C242, C2510, T195s, T220,
T222,T230,
T230s,
STIHL
FS110,T220,
FS130,
FS250,
FS40,
FS44,
FS45,
FS46,T2510,
FS48, FS52,
FS56,
T195,
T222,
T230,
T230s,
T242,
T242X,
T2510X
FS350,
FS450,
FS550
T242,
T242X,
T2510,
T2510X
FS62,
FS108,FS120,
FS200,
FS50, FS66,
FS51, FS85,
FS55, FS86,
FS60, FS88,
FS61, FS96,
FS65, FS106,
FS80, FS83,
FS85, FS86,
STIHL
T260,
T261,
T261B/XR/XB,
T272,
T272X,
T282,
T282X,
T300,
C3410,
C260,
T260, T261, T261B/XR/XB, T270, T272,
FS350,
FS450,
FS550
FS90, FS91,
FS96
T3410,FS51,
T3410X,
T350
T272X,
T282,
T3410X,
FS50,
FS55,
FS60,T3410,
FS61,DOLMAR
FS65,
FS80, T350
FS83, FS85, FS86,
DOLMAR
/T300,
SACHS
FS66, FS74, FS76,
FS81, FS83,
FS85, FS86, FS100, FS106, FS108,
FS90,
FS91,
FS96 C350
BP35,
B45,
B450,
BC250,
BC330,
BC400,
PRO400,
SD330,
BP35,
B450,
C350
FS110, B45,
FS130,
FS250,
FS40,PRO370,
FS44, FS45,
FS46, FS48,
FS52, LT250
FS56,
FS66,
FS74,
FS76,
FS81,
FS83,
FS85,
FS106, FS108,
FS62,F20,
FS66,
FS85,
FS86,
FS88,
FS96, FS86,
FS106,FS100,
FS108,FS120,
FS200,
F18,
F21,
F22,
F230,
F195F195s,
F18,
F20,
F21,
F22,
F230,
FS110,
FS130,
FS250,
FS40,
FS44, FS45,22F
FS46, FS48, FS52, FS56,
FS350,
FS450,
FS550
FS62, FS66, FS85, FS86, FS88, FS96, FS106, FS108,FS120, FS200,
FS350, FS450, FS550
REF#
RH2
LH6
REF#
LH3
RH2
LH4
LH3
LH6
LH4
RH2
LH6
LH3
RH1
RH2
REF#
RH1
LH3
LH3
LH4
LH3
LH6
RH1
RH2
RH1
LH6
LH3
LH3
LH2
LH3
LH2
LH3
LH6
LH3
LH6
RH1
LH2
LH1
LH2
LH3
LH3
LH1
LH3
LH2
LH6
LH2
LH1
LH3
LH1
LH2
LH3
LH6
LH2
LH3
LH6
LH2
LH3
LH1
LH1
LH3
LH1
LH6
LH1
LH1
LH2
LH2
LH6
LH2
LH2
LH3
LH3
LH2
RH2
LH3
RH2
LH3
LH1
LH1
RH2
RH2
LH1
LH1
LH2
LH2
LH3
LH2
LH3
LH2
LH3
LH6
LH2
RH2
LH3
RH2
LH3
LH2
RH2
RH2
LH5
LH1
LH1
LH5
LH2
LH2
LH2
LH2
LH3
LH3
LH5
RH2
RH2
LH5
Speed-Feed ® Trimm
Tabla De Aplic
Tableau D’A
Left
HandThread
Thread
Trimmer
Units
Left Hand
Trimmer
Units
UniversalSpeed-Feed
Speed-Feed®® Trimmer
*Trimmer
Head
Part
Numbers:
Universal
Head
Part
Numbers:
P/N 78890-18001 375 LH Trimmer Head
P/N 78890-18000 375 LH Trimmer Head
P/N 78890-21001 High Capacity LH Trimmer Head
P/N 78890-21000 450 LH Trimmer Head
Reference# #
Reference
LH1
7mm x 1.0LHM
Gold
LH2
FS66, FS74, FS76, FS81, FS83, FS85, FS86, FS100, FS106, FS108,
FS110, FS130, FS250, FS40, FS44, FS45, FS46, FS48, FS52, FS56,
FS62, FS66, FS85, FS86, FS88, FS96, FS106, FS108,FS120, FS200,
FS350, FS450, FS550
LH5
RH1
Gold
Reference# #
Reference
LH2
8mm x 1.25LHM
Gold
Reference
Reference# #
LH3
Silver
10mm x 1.25LHM
Red
Reference# #
Reference
LH4
Gold
8mm x 1.25LHF
Red
Reference# #
Reference
LH5
Green
Reference# #
Reference
LH6
Gold
78890-11390
10mm x 1.0LHF
78890-11400
*
10mm x 1.25LHF
OR
78890-11400
78890-11380
STIHL
FS50, FS51, FS55, FS60, FS61, FS65, FS80, FS83, FS85, FS86,
FS90, FS91, FS96
Reference #
78890-15340
X7672050701
01/11
Reference #
RH2