D—îŸ^7 vôÅ Œˇl°©æÍ
Transcripción
D—îŸ^7 vôÅ Œˇl°©æÍ
Sistema de Corredera para Closet Compacto D-50 Corredera al piso para closet con riel y guía de aluminio. De gran resistencia y suavidad. Práctico sistema Furniture and Closet Sliding Door Hardware de regulación a través de llave de puntas. La reversibilidad del sistema permite su instalación embutida o sobrepuesta. Capacidad de carga de 50 Kgs por hoja. Sliding closet door floor wheel with aluminum track and overhead guide. Highly durable; exceptionally smooth operation. Load capacity: 50 Kgs (110 Lbs) per door panel. DUC SSE I N T E R N A C I O N A L Sistemas de Correderas para Muebles y Closet Compacto D-50 Sliding Closet Door Floor Wheel System Sistema de Corredera para Closet Compacto D-50 CD-50 Sliding Closet Door Floor Wheel System CARACTERISTICAS TECNICAS Technical Specifications Tipo de Corredera Corredera al piso con sistema de regulación controlada. Utiliza Riel D-52 y Riel Canal CD-50 en aluminio. Carrier Type: Closet door floor wheel. For use with D-52 aluminum track and CD-50 overhead aluminum guide. Capacidad de Carga CD-50 Load Capacity D-52 Isométrica Isometric Drawing FRENO COMPUESTO Retention Catch RIEL CANAL CD-50 Aluminio CD-50 Overhead Aluminum Track : 50 Kgs por hoja : 50 Kgs (110 Lbs) per door panel. GUIA SUPERIOR Overhead Guides Systems Las características de sus rodamientos otorgan a los carros propiedades de : Extrema suavidad de rodadura Rodamientos de acero templado con pista exterior de acero revestida en nylon 6.6 100% vírgen . Pistas de acero endurecidas con tratamiento térmico. Dureza de 55 a 60 Hrc. Zincado cromatizado resistente a la oxidación. Juego radial de 10 a 30 micras. Pista interior pulida. Lubricado con grasa. High quality ball bearing wheel(s) assure exceptionally smooth operation: Tempered steel ball bearing races, both with rust-proof zinc-plated finish; outer race attached to 100% virgin nylon 6.6 wheel. Hardness from 55 to 60 hrc. Radial tolerance : 10 to 30 microns. Inner race: polished. Lubricated for life with grease. CORREDERA CD-50 CD-50 Door Floor Wheel LLAVE DE PUNTAS M5 M5 Wrench RIEL D-52 Aluminio D-52 Aluminum Track Prolongada vida útil ( vida útil estimada 10 años-20.000 ciclos ) Long Service Life (10 years -20.000 cycles estimated service life) COMPONENTES del Set para dos hojas CD-50 :4 carros Compacto D-50 , 2 guias superiores derechas, 2 guias superiores izquierdas, 4 frenos,llave M5,tornillos CD-50 contents for two door panels four CD-50 Door Floor Wheels, two right guides, two left guides, four retention catch ,M5 wrench, screws Plano Esquemático Schematic Drawing VISTA FRONTAL Front View VISTA LATERAL Lateral View 100.0 La distancia para ubicar el freno depende directamente del ancho de la puerta y por lo tanto de la ubicación del carro The position of the retention catch depends directly of the width of the door, which affects the location of wheel hanger 23 mm 20.5 DIMENSIONAMIENTO de las PUERTAS La puerta debe medir entre 39 y 45 mm menos que el alto total del vano. El traslape entre puertas debe ser entre 25 y 30 mm. 8 73 mm r:17.5 mm r:17.5 mm 14 mm 18 mm min. 56 mm 100 mm 83 mm DOOR SIZE The hight of the door should be 39-45 mm ( 1.53-1.77 in) less than the total height of the door closet opening The door overlap should be 25-30 mm (0.98-1.18 in) 63 mm 31 mm 15.0 18 mm ALTERNATIVAS DE INSTALACIÓN 1. sistema de sobreponer: No precisa mecanización 2.sistema de embutir: Precisa mecanización 56mm (ancho) x 63 mm (alto) x 14 mm (profundidad) con fresa ø35 mm. Se recomienda 18 mm. mínimo para espesor de hoja. 14.0 63.5 mm INSTALLATION ALTERNATIVES 1.Overlapped system: It does not need mechanization. 12.0 2.Insert System: Precise mechanization 56 mm (2.2 in) (Wide) x 63 mm (2.5 in) (high) x 14 mm (0.55 in)(depth) with a drill ø35 mm. It`s recommends 18 mm. minimum door thickness. 12.0 18.5 millimeters to inches coversion factor: 0.03937 Cualidades Features El sistema de sobreponer no precisa mecanización, mientras que el sistema de embutir permite una mínima separación entre puertas. Overlay installation does not require wheel mechanism near top of closet door. Embedded installation allows minimal distance between the door panels. Absolutamente silencioso. Exceptionally smooth, quiet operation. Usos Puertas de corredera de madera, metal y espejadas de closets y vitrinas. For wood, metal and mirrored closet doors and display cases.
Documentos relacionados
Sistema de Corredera para Closet D-52 Sistemas
Isométrica Isometric Drawing GUÍA SUPERIOR D-52 Aluminio D-52 Overhead Aluminum Track
Más detallesSistemas de Correderas para Muebles y Closet
Wheel specially designed to have a secure fit with track. Tempered steel ball bearing races, both with rust-proof zinc-plated finish; outer race attached to 100% virgin nylon 6.6 wheel. Hardness fr...
Más detallesSistemas de Correderas para Muebles y Closet
Sliding furniture door floor wheel with aluminum track and overhead guide. Exceptionally smooth operation. Clip system for quick and easy mounting. Minimum space between the door and the closet ope...
Más detalles